CITROEN C3 PICASSO 2009 Owners Manual

11
149
PRACTICAL INFORMATION

Dashboard fuses

The fusebox is located in the glove box.

Access to the fuses


)
refer to the paragraph "Access to
the tools".

Fuse tables


Fuse N°



Rating


Functions



FH36



5 A

Trailer relay unit.


FH37



15 A

Trailer accessories socket supply.


FH38



20 A

Navigation.


FH39



-

Not used.


FH40



30 A

Trailer relay unit.


Fuse N°



Rating


Functions



F1



15 A

Rear wiper.


F2



-

Not used.


F3



5 A

Airbags and pretensioners control unit.


F4



10 A

Steering wheel angle sensor, air conditioning,
clutch switch, particle fi lter pump, diagnostic
socket, airfl ow meter.


F5



30 A

Electric windows panel, passenger’s electric
window control, front electric windows motor.


F6



30 A

Rear electric windows motor and driver’s electric
window motor.


F7



5 A

Courtesy and front map reading lamps, torch, rear
reading lamps.

11
150
PRACTICAL INFORMATION


Fuse N°



Rating


Functions



F8



20 A

Multifunction screen, audio system, navigation
radio.


F9



30 A

Audio system (fi tted as an option), 12 V socket.


F10



15 A

Steering mounted controls.


F11



15 A

Ignition, diagnostic socket.


F12



15 A

Rain/sunshine sensor, trailer relay unit.


F13



5 A

Main stop switch, engine relay unit.


F14



15 A

Parking sensors control unit, seat belt unfastened
warning lamp, airbag control unit, instrument panel,
air conditioning, USB Box.


F15



30 A

Locking.


F16



-

Not used.


F17



40 A

Rear screen and door mirrors demist/defrost.


SH



-

PARC shunt.

11
151
PRACTICAL INFORMATION

Engine compartment fuses

The fusebox is placed in the engine
compartment near the battery (left-hand
side).
All work on the fusebox located
on the battery must be carried
out by a CITROËN dealer or a
qualifi ed workshop.
Access to the fuses


)
Unclip the cover.

)
Change the fuse (see correspond-
ing paragraph).

)
When you have fi nished, close the
cover carefully to guarantee the
sealing of the fuse box.

11
152
PRACTICAL INFORMATION


Fuse N°



Rating


Functions



F1



20 A

Engine control unit supply, cooling fan unit control, multifunction engine control main
relay.


F2



15 A

Horn.


F3



10 A

Front/rear wash-wipe.


F4



20 A

Daytime running lamps.


F5



15 A

Diesel fuel heater (Diesel engine), fuel pump (petrol engine)


F6



10 A

ABS/ESP control unit, ABS/ESP cut-off relay, secondary stop switch.


F7



10 A

Electrical power steering.


F8



25 A

Starter control.


F9



10 A

Switching and protection unit (Diesel).


F10



30 A

Diesel engine injection pump valve, injectors and ignition coils (petrol engine)


F11



40 A

Air conditioning fan.
Fuse table

11
PRACTICAL INFORMATION


Fuse N°



Rating


Functions



F12



30 A

Windscreen wipers slow/fast speed.


F13



40 A

Built-in systems interface supply (ignition positive).


F14



30 A

Valvetronic supply (petrol).


F15



10 A

Right-hand main beam headlamp.


F16



10 A

Left-hand main beam headlamp.


F17



15 A

Left-hand dipped headlamp.


F18



15 A

Right-hand dipped headlamp.


F19



15 A

Multifunction engine control supply (petrol engine),
air cooling electrovalves (Diesel).


F20



10 A

Multifunction engine control supply (petrol engine),
Turbo pressure regulation valve (Diesel), engine
coolant level detector (Diesel).


F21



5 A

Fan assembly control supply, APC, ABS ESP
relays.

11
154
PRACTICAL INFORMATION

Table of maxi-fuses


Fuse N°



Rating


Functions



MF1 *



60 A

Cooling fan assembly.


MF2 *



30 A

ABS/ESP control unit.


MF3 *



30 A

ABS/ESP control unit.


MF4 *



60 A

Built-in Systems Interface (BSI) supply.


MF5 *



60 A

Built-in Systems Interface (BSI) supply.


MF6 *



-

Not used.


MF7 *



-

Dashboard fusebox.


MF8 *



-

Not used.

*
The maxi-fuses provide additional protection for the electrical systems. All work on the maxi-fuses must be carried out by a
CITROËN dealer or a qualifi ed workshop.

11
PRACTICAL INFORMATION
BATTERY
Procedure for charging your battery
when it is fl at or for starting the engine
using another battery.
Access to the battery
Starting using another battery



)
Connect the red cable to the posi-
tive terminal (+) of the fl at battery A
,
then to the positive terminal (+) of
the slave battery B
.

)
Connect one end of the green or black
cable to the negative terminal (-) of the
slave battery B
.

)
Connect the other end of the green
or black cable to the remote nega-
tive terminal (-) of your vehicle.

)
Start the slave vehicle.

)
Operate the starter of the broken
down vehicle and let the engine run.

)
Wait until the engine returns to idle
and disconnect the cables.
The battery is located under the bonnet.
To gain access to it:


)
open the bonnet using the interior
release lever, then the exterior safety
catch,

)
secure the bonnet stay,

)

lift the plastic cover on the (+) terminal.








The presence of this label, in
particular with the Stop & Start
system, indicates the use of a
12 V lead-acid battery with spe-
cial technology and specifi cation;
the involvement of a CITROËN
dealer or a qualifi ed workshop is
essential when replacing or dis-
connecting the battery.
Failure to observe this recommen-
dation may cause premature wear
of the battery.


After refi tting the battery by a
CITROËN dealer or a qualifi ed
workshop, the Stop & Start system
will only be active after a continu-
ous period of immobilisation of the
vehicle, a period which depends
on the climatic conditions and the
state of charge of the battery (up to
about 8 hours).

11
156
PRACTICAL INFORMATION
Batteries contain harmful sub-
stances such as sulphuric acid
and lead. They must be dis-
posed of in accordance with
regulations and must not, in any
circumstances, be discarded
with household waste.
Take used remote control bat-
teries and vehicle batteries to a
special collection point.
Charging the battery using a battery charger LOAD REDUCTION MODE

System which manages the use of
certain functions according to the level
of charge remaining in the battery.
When the vehicle is being driven, the
load reduction function temporarily de-
activates certain functions, such as
the air conditioning, the heated rear
screen...
The deactivated functions are reactivat-
ed automatically as soon as conditions
permit.

Do not push the vehicle to start
the engine if your vehicle is fi t-
ted with the electronic gearbox
system.

Do not disconnect the battery to
charge it.


)
Follow the instructions for use pro-
vided by the manufacturer of the
charger.

11
157
PRACTICAL INFORMATION
A fl at battery prevents the en-
gine from starting (refer to the
corresponding paragraph).
If the telephone is being used
at the same time on the MyWay
audio navigation system, it will
be interrupted after 10 minutes.
ENERGY ECONOMY MODE

System which manages the period of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
beam headlamps, courtesy lamps, etc.
for a maximum combined period of
thirty minutes.
This period may be greatly reduced if
the battery is not fully charged.
Exiting economy mode
These functions are reactivated auto-
matically the next time the vehicle is
driven.


)
In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be dou-
ble the period for which the engine is left
running. However, this period will always
be between fi ve and thirty minutes.


Switching to economy mode

Once this period has elapsed, a mes-
sage appears on the multifunction
screen indicating that the vehicle has
switched to economy mode and the
active functions are put on standby.
CHANGING A FRONT OR REARWIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.
Removal



)
Raise the corresponding wiper arm.

)
Unclip the wiper blade and remove it.



Fitting



)
At the front, check the size of the
wiper blade as the shorter blade is
fi tted to the passenger side of the
vehicle.

)
Put the corresponding new wiper
blade in place and clip it.

)
Fold down the wiper arm carefully.



Before removing a front wiper blade



)
Within one minute after switching off
the ignition, operate the wiper stalk
to position the wiper blades in the
vertical position.
This position must be used in order to
avoid damaging the wiper blade and the
bonnet.


After fitting a front wiper blade



)
Switch on the ignition.

)
Operate the wiper stalk again to
park the wiper blades.

11
158
PRACTICAL INFORMATION
TOWING THE VEHICLE

Access to the tools

The towing eye is installed under the
boot fl oor.
To gain access to it:


)
open the boot,

)
remove the adjustable boot fl oor,

)
lift up the boot carpet,

)
remove the towing eye from the tool
holder.



General recommendations

Observe the legislation in force in your country.
Ensure that the weight of the towing vehicle is higher than that of the towed
vehicle.
The driver must stay at the wheel of the towed vehicle.
Driving on motorways and fast roads is prohibited when towing.
When towing a vehicle with all four wheels on the ground, always use an
approved towing bar; rope and straps are prohibited.
When towing a vehicle with the engine off, there is no longer any power
assistance for braking or steering.
In the following cases, you must always call on a professional recovery
service:


- vehicle broken down on a motorway or fast road,

- when it is not possible to put the gearbox into neutral, unlock the steering,
or release the parking brake,

- towing with only two wheels on the ground,

- where there is no approved towing bar available...
Procedure for having your vehicle towed
or for towing another vehicle using a re-
movable towing eye.