Citroen C3 PLURIEL 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 127
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT 2002XSARA
Tools.
[1]
Belt tension measuring instrument :4122T
(1)
Tensioning screw.
(2)Roller support fixing screw (3).
Lightly tighten the screws
(2).
Place the tool
[1]on the belt.
Tension the belt using the screw
(1).
• Reused belt
90 SEEM units.
• New belt
120 SEEM units.
Tighten the screws
(2)to 2 m.daN.
Remove the tool
[1].
Rotate the crankshaft by 3 turns
(direction of rotation).
Check the belt tension using the tool
[1], and adjust (if necessary).
Without air conditioning.
B1EP12YCB1EP12XC
Engine: RFS

Downloaded from www.Manualslib.com manuals search engine 128
ENGINEAUXILIARY EQUIPMENT DRIVE BELT 2002
Engines: 6FZ RFN
Without air conditioning.With air conditioning.
Tools.
[1]
Pliers for removing plastic pegs :7504T
Remove the belt.
Detension the belt (3)by turning the screw (2)of the tensioner roller (1)(anticlockwise).
The screw
(2) (WARNING: not left hand screw).
Remove the belt (3), while keeping the tensioner roller (1)tight.
Refit the belt. Refit the belt (3), while keeping the tensioner roller (1)tight.
Release the tensioner roller (1).
B1BP23PCB1BP23QCB1BP23PCB1BP23RC
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 129
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT 2002
Sans Powerassisted steering.
Tools.
[1]
Belt tension measuring instrument: 4122T
Removal.
Loosen the screws (2).
Tighten the screw (1)until it is against its stop.
Remove the belt.
Refitting. Refit the belt.
Fit the tool [1]on the belt at "d".
Tighten the screw (1)to obtain:106 ±10 SEEM units. Tighten the screws (2)to 2 m.daN.
Remove the tool [1].
B1BP1SECB1BP1SDC
Engine: WJY
XSARA

Downloaded from www.Manualslib.com manuals search engine 130
ENGINEXSARAAUXILIARY EQUIPMENT DRIVE BELT 2002
Sans Powerassisted steering With air conditioning.
Tools.
[1]
Belt tension measuring instrument: 4122T
Removal.
Loosen the screws (1).
Tighten the screw
(2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool
[1]at "e".
Tighten the screw
(2)to obtain:106 ±10 SEEM units.
Tighten the screws (1)to 2 m.daN.
Remove the tool
[1].
B1BP1SGCB1BP1SFC
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 131
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering without air conditioning.
Tools.
[1]
Belt tension measuring instrument: 4122T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
the screw
(1).
the nut
(2).
NOTE:The tensioner arm (3) must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 132
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Powerassisted steering without air conditioning (continued).
XSARA
Refitting. Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1], with the knob downwards. Tighten the nut (2)to obtain a value of :
Reused belt:Keep the value taken at removal.
New belt:Tension should be 110 SEEM units.
Tighten the screw (1)to 9.5 m.daN.
Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEM units.
Remove the tool [1].
Start the engine and run it for 10 seconds.
Stop the engine.
Place the tool
[1]on the belt at "f".
Tension should be 130 ± 4 SEEM units.
Remove the tool [1].
B1BP1SJD

Downloaded from www.Manualslib.com manuals search engine 133
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering with air conditioning.
Tools.
[1]
Dynamic tensioner peg: () 0188 H
[2]Belt tension measuring instrument: 4122T
Removal.
Peg the dynamic tensioner (1)at "a", using tool [1].
Loosen the screw (2)of the roller (3).
Turn the roller (3)backwards.
Remove the belt.
NOTE:If it can not be pegged at "a":
Loosen the screw (2)of the roller (3).
Using a 7 mmsquare drive, turn the roller (3)at "b".
Peg the tensioner (1)at "a", using tool [1].
NOTE:If the belt is broken:
Support the engine using a jack (insert a wooden block between the housing and the jack).
Remove the right engine support. Using a square drive at
(b)turn the tool (3)in the direction of the arrow "a", so that it can be
pegged at "a"using the tool [1].
B1BP1SKC
Engine: WJY

Downloaded from www.Manualslib.com manuals search engine 134
ENGINEAUXILIARY EQUIPMENT DRIVE BELT 2002
Powerassisted steering with air conditioning (continued).
Refitting.
Refit the belt.
Using a
7 mm squaredrive at "b", turn the roller (3), until the tool [1]located at "a"becomes
free.
Tighten the screw
(2).
Remove the tool
[1].
B1BP1SLC
Engine: WJY
XSARA

Downloaded from www.Manualslib.com manuals search engine 135
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
With compressor and alternator .
B1BP2MKCB1BP2MJD
Tools.
[1]
Pliers for removing plastic pegs: 7504T
[2]Tensioner roller compression lever:().0194.E
[3]Tensioner roller setting peg Ø4 mm: ().0194.F
Removing.
Disconnect the battery negative cable.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel.
Move aside the splashshield, using tool
[1].
IMPERATIVE: In the case of belt reuse, mark the
direction of rotation of the belt. If the index on the
tensioner roller is outside the marks, change
the auxiliary equipment drive belt.
The alternator (1).
The aircon compressor (2).
Detension the auxiliary belt tensioner roller, using tool [2].
Position the peg [3].
Remove the auxiliary drive belt.
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 136
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: 8HX 8HW
Markings on the dynamic tensioner roller.
«a»
Position of «maximum wear» of the auxiliary drive belt.«b»Normal position.
Refitting.
NOTE:
Check that the tensioner roller moves freely (no tight spot). If this is not the
case, replace the tensioner roller.
Respect the direction of fitting of the drive belt.
Complete the setting of the belt, of both sides, by means of the tensioner roller.
Make sure that the drive belt is correctly positioned in the
«V»grooves of the
various pulleys.
Move the tool
[2]on the tensioner roller to remove the peg [3].
B1EP18UD
C2 C3 C3 PLURIEL