Cable Citroen C3 PLURIEL 2004 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 327
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Engines: 8HV 8HY
Adjustment.
The gear selection control and gear engagement
control cables cannot be adjusted.
To release the balljoint, press at
«d»then pull the
balljoint upwards.
To release sleeve stops:
Press on the tabs of the clip
(6)at «a».
Disengage the sleeve stops from their supports.
B2CP3J6D
C3

Downloaded from www.Manualslib.com manuals search engine 328
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX CONTROLS
Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
(1)Gear control lever.
(2) Gear engagement control cable.(*)
(3)
Gear selection control cable.(*)
(4)
Gear selection balljoint Ø 10 mm.
(5) Gear engagement balljoint Ø 10 mm.
(6) Flexible insulating grommet through the bulkhead.
(*)= These two cables cannot be separated.
B2CP3BWD
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 329
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Principles of adjusting the gear controls.
WARNING: Cables should be adjusted each time the gearbox, gear controls or power unit are
removed.
Principles.
Lock the gear lever in neutral position, using tool:9607T.
Place the gearbox in neutral.
Couple the cables on the lever.
Fit the balljoints on the gearbox lever.
Lock the cable lengths with the balljoint locking keys.
WARNING: Do not use any tool to unclip the balljoints.
To unlock the balljoint, press at the centre «a», then pull the balljoint upwards.
NOTE:Changing an individual balljoint is possible as long as the locking key is removed.
Unclip at «b», using two small screwdrivers.
Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3BXCB2CP3BYC

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
CHECKS AND ADJUSTMENTS: BE4/5 GEARBOX CONTROLS
Tools.
[1] Tool for positioning the gear lever: 9607T.
Adjustements.
WARNING: Cables should be adjusted each
time the gearbox, gear controls or power unit
are removed.
Inside the vehicle:
Remove the trim under the gear lever.
Lock the gear lever in neutral position,
using tool
[1].
Under the bonnet: Remove the air filter assembly.
Unlock the balljoint keys at «a».
Place the gear selection and control levers on
neutral.
Lock the cable lengths with the balljoint locking
keys.
Checks.
Remove the tool [1].
Check that all the gears engage without
«tightness ».
Check that the gear lever moves identically
forwards and backwards and to right and left. If it
does not, repeat the adjustment.
Refit the trim under the gear lever.
Refit the air filter assembly.
Adjusting the gear controls Engines: NFV 6FZ RFN RFS WJY 8HZ 9HZ 9HY RHY RHZ
XSARA XSARA PICASSO
B2CP3C6CB2CP3C0C

Downloaded from www.Manualslib.com manuals search engine 335
CLUTCH
GEARBOX
TRANSMISSION
Engines: KFV NFU RFN RHZ
Updating the value of the oil usage counter.
Using PROXIA.
Access to reading and recording of the oil counter is via the menu:
«Configuration
(integrated circuit button)/ Oil counter».
Adjustment of the oil counter value is done in incremental steps of
2750units.
Using LEXIA or ELIT.Access to reading and recording of the oil counter is via the menu:
«Oil counter».
Adjustment of the oil counter value is done by entering directly the
5 figures of the oil counter.
Downloading.
ECU downloading procedure:
Follow the diagnostic tool procedure.
A new ECU or downloaded update is always configured with the
following options:
SHIFT LOCK gear selection lever position.
Without OBD outlet
(depollution L4).
If the ECU is to be fitted to a vehicle with depollution
L4or not
equipped with gear lever locking safety: Perform a configuration operation.
Pedal initialisation.
A pedal initialisation must be carried out in the following cases:
Replacement of the automatic gearbox ECU.
Replacement of the automatic gearbox.
Downloading of the ECU configuration.
Adjustment or replacement of the accelerator cable.
Replacement of the butterfly potentiometer.
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOXC3 XSARA XSARA PICASSO
Procedure for initialising the automatic gearbox ECU

Downloaded from www.Manualslib.com manuals search engine 342
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
The automatic gearbox is controlled by a cable.
«c»or «d»Pushbutton.
(1)Control lever with balljoint.
(2)Automatic adjustment (pull out the button to adjust the control, push it in to lock the
adjustment of the control).
(3)Sleeve stop.
(4)Selection control locking clip (5)on the sleeve stop(3).
Engines: KFV RFN
C3 XSARA PICASSO
B2CP3H8CB2CP3N7C
XSARA PICASSOC3

Downloaded from www.Manualslib.com manuals search engine 344
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Gearbox end.
(1)
Control lever.
(2)Automatic adjustment.
(3) Sleeve stop.
The automatic gearbox is controlled by a cable.
Engines: NFU RFN RHZ
XSARA
XSARA

Downloaded from www.Manualslib.com manuals search engine 348
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Refitting the gearbox control.
New gear selection control
Couple the balljoint (3).
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Reused gear selection control.
Release the component (a).
Couple the balljoint (3).
Push in the component (a)without bending the cable.
Check all the gear selection control positions.
Engine: KFV
C3
C3
B2CP3GYD

Downloaded from www.Manualslib.com manuals search engine 349
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Refitting the gearbox control.
Proceed in the opposite order to removal.
IMPERATIVE: To adjust the gear selection control, place the gear selection lever in the
park position. Press on the component (25) without bending the cable, then release.
IMPERATIVE: Check that all the gears can engage.
Engines: NFU RFN RHZ
XSARA
B2CP3AXC

Downloaded from www.Manualslib.com manuals search engine 350
CLUTCH
GEARBOX
TRANSMISSION
AL4 AUTOMATIC GEARBOX
Refitting.
Proceed in the opposite order to removal.
Lubricate the support
(13).
New gear selection control.
Couple the balljoint(6).
WARNING:Do not deform the selection lever on the automatic gearbox.
Push in the component
(a) without bending the cable.
Check all the gear selection control positions.
Reused gear selection control.
Release the component (a).
Couple the balljoint (6).
Push in the component (a) without bending the cable.
Check all the gear selection control positions.
Engine: RFN
XSARA PICASSO
B2CP3GYD