run flat Citroen C3 RHD 2013 2.G Owner's Manual

Driving
126
Manual operation
)Select position M for sequentialchanging
of the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to changedown a gear.
It is onl
y possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the instrument panel.


Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N to place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle.

Operating fault
When the ignition is on, the lighting
o
f this warning lamp, accompanied by an audible signal and a message in the multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
To r e d u c e fuel consumption when at a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.



There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,


- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the message disappears.

If the en
gine speed is too low or too high, the gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not
operate in manual mode.

Practical information
150
2. Infl ation
)Turn the selector Ato the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
) Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave the engine running.

)Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that thepuncture has not been fully plugged; contact a CITROËN dealer or qualified
workshop for assistance.)Remove and stow the kit.)Drive at reduced speed (50 mph [80 km/h] max) limiting the distance travelled toapproximately 120 miles (200 km).




As soon as possible, go to a CITROËNdealer or a qualified workshop.You must inform the technician that you have used this kit. After inspection, the technician will advise you on whether
the tyre can be repaired or if it must be replaced.

11
Practical information
151

Removing the cartridge
)Stow the black pipe. )Detach the angled base from the white pipe.)Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.
Checking tyre pressures /
inflating accessories
You can also use the compressor, without
injecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).

)
Turn the selector Ato the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
) Connect the compressor's electrical connector to the vehicle's 12 V socket. )
Star t the vehicle and let the engine run. )
Adjust the pressure using the compressor (to inflate: switch B
in position "I" ; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. ) Remove the kit then stow it.




Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for single use; even if only par tly used, itmust be replaced. After use, do not discard the car tridgeinto the environment, take it to an authorised waste disposal site or a CITROËN dealer.
Do not forget to obtain a new sealant
cartridge, available from CITROËN dealers or from a qualified workshop.

11
Practical information
159





Snow chains


In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when
braking.

The snow chains must be fitted only to the front wheels. They must never be fitted to "space-saver" type sparewheels.
Take account of the legislation in force in your country on the use of snowchains and the maximum running speedauthorised.


Avoid driving on roads that have beencleared of snow, to avoid damaging your vehicle's tyres and the road surface. It is recommended that before you leave, you practise fitting the snowchains on a level and dry surface.If your vehicle is fitted with alloy wheels, check that no par t of the chain or itsfixings is in contact with the wheel rim. Use onl
y the chains designed to be fitted to the
type of wheel fitted to your vehicle:
Original tyre size Maximum link size.
1
85/65 R15 9 mm
195/55 R16

205/45 R17 not chainable
For more information on snow chains
, contact a
CITROËN dealer or a qualified workshop.



Advice on installation
)
If you have to fit the chains during ajourney, stop the vehicle on a flat surface on the side of the road.)
Apply the parking brake and position anywheel chocks to prevent movement of your
vehicle. ) Fit the chains following the instructions provided by the manufacturer.)
Move off gently and drive for a few moments, without exceeding 30 mph(50 km/h). )
Stop your vehicle and check that the snowchains are correctly tightened.

11
Practical information
175

Starting using another
batter
y

Charging the battery using
a battery charger

When the battery on your vehicle is discharged,
the engine can be star ted using a slave battery (external or on another vehicle) and jump leads.
) Follow the instructions for use provided by
the manufacturer of the charger.

First check that the slave battery has a nominal
voltage of 12 V and a capacity at least equal to
that of the discharged battery.
Do not try to star t the engine by connecting a
batter
y charger.
Do not disconnect the (+) terminal when theengine is running.
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B
.)Connect one end of the green or blackcable to the negative terminal (-) of the slave battery B
(or ear th point on the other
vehicle).)Connect the other end of the green or black cable to the negative terminal C(or
the engine mounting) of the broken-down
vehicle.)Star t the engine of the other vehicle and
allow it to run for a few minutes.
Do not disconnect the battery to charge it.
)
Operate the star ter of the broken-down
vehicle and let the engine run.
If the engine does not star t immediately, switch off the ignition and wait a few
moments before trying again.) Wait until the engine returns to idle, then
disconnect the jump leads in reverse order.


Batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordance with regulationsand must not, in any circumstances, bediscarded with household waste.
Take used remote control batteries and vehicle batteries to a special collection
point.

11
Practical information
177








Energy economy mode


Exiting economy mode

These functions are reactivated automatically
the next time the vehicle is driven. ) In order to resume the use of thesefunctions immediately, star t the engine and
let it run for a few minutes.
The time available to you will then be double
the period for which the engine is left running. However, this period will always be between five and thir ty minutes.
Switching to economy mode
Once this period has elapsed, a message appears on the multifunction screen indicating
that the vehicle has switched to economy mode and the active functions are put on standby.
A flat battery prevents the engine from starting (refer to the correspondingparagraph).
If the telephone is being used at thesame time on the eMyWay audionavigation system, it will be interrupted after 10 minutes. S
ystem which manages the period of use of certain functions to conserve a sufficient level
of charge in the battery.
After the engine has stopped, you canstill use functions such as the audio
equipment, windscreen wipers, dippedbeam headlamps, cour tesy lamps, etc. for a
maximum combined period of thirty minutes. S
ystem which manages the use of cer tain
functions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates certain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated
automatically as soon as conditions permit.








Load reduction mode
This period may be greatly reduced if the battery is not fully charged.