c4 engine support Citroen C4 2005 2.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 270
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY - RHZ
Remove:
- Tools [3]and [5], Screw (7)and the spacer.
Refit:
- The lower, intermediate and upper covers (5).
- Screw (7), tighten to 1,5 ± 0,1 m.daN.
- Screws (3), (4)and (6).
- The bracket (13).
Screws (11), tighten to 6,1 ± 0,5 m.daN.
The nut (12), tighten to 4,5 ± 0,5 m.daN.
Fit the bearing shell (10).
Take away the workshop hoist.
Clip the fuel delivery and return pipes.
Remove the tool [7].
Couple:
- The fuel delivery pipe (12).
- The fuel return pipe (1).
- Coat the screw (8)with loctite FRENETANCH.
Refit the tool [6]and the screw (8)with the washer (22), tighten to 7 ± 0,2 m.daN
and angular tighten to A= 60°±5°.
Refit the torque reaction rod on the lower engine support.
Remove the tool [6].
Reposition and reclip the cooling hose.
Complete the refitting of components in reverse order to removal.
B1EP1A7CB1BP2R4CB1EP1ADC
XSARA - XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 270

Downloaded from www.Manualslib.com manuals search engine 271
ENGINE
CHECKING THE VALVE TIMING
Engine: RHR
Tools.
[1] Kit of plugs: (-).0188.T
[2] Double flywheel setting peg: (-).0188.X Toolkit 0188-T
[3]Camshaft setting peg: (-).0188.M
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Remove the engine cover and the battery.
Disconnect the negative terminal of the battery.
Raise and support the front of the vehicle.
Remove the under-engine sound-deadening and the front RH splash-shield.
Uncouple, plug and move aside, using tool [1], the fuel supply and fuel return pipes..
Suspend the engine, using a workshop hoist.
Remove the engine support bracket and the engine support.
Move aside the electrical harness (1).
Remove:
- The camshaft position sensor.
- The inlet cylinder head cover (2).
- The upper timing cover screws.
- The upper timing cover (3).
B1EP1GFC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 271

Downloaded from www.Manualslib.com manuals search engine 273
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Tools.
[1]Kit of plugs: (-).0188.T
[2]Double flywheel setting peg: (-).0188.X
[3]Camshaft setting peg: (-).0188.M
[4]Belt clamp: (-).0188.AD
[5]Pinion centrer: (-).0188.AH
[6]Flywheel lock: (-).0188.F
[7]Pulley(-).0188.P
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel injection (HDi) engine versions.
Removing.
Slacken the front RH wheel bolts.
Raise and support the front RH side of the vehicle.
Disconnect the negative terminal of the battery.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield.
- The engine cover.
Remove the auxiliaries drive belt
(see corresponding operation).
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 273

Downloaded from www.Manualslib.com manuals search engine 274
ENGINE
274
CHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Uncouple, plug and move aside, using tool [7],
the fuel delivery pipe (1)and the fuel return pipe (2).
Suspend the engine, using a workshop hoist.
Remove the bracket (3)and the RH engine
support (4).
Move aside the electrical harness (5).
Remove:
- The upper timing cover screws.
- The upper timing cover (6).
Rotate the engine by means of the auxiliaries drive
pulley.
Orient the camshaft pinion in the pegging position,
use a mirror if necessary.
Peg the camshaft, using tool [3].
Peg the engine flywheel, using tool [2].
Lock the flywheel, using tool [6].
B1BP351C
B1EP1FAC
B1EP1FBC
B1BP31EC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 274

Downloaded from www.Manualslib.com manuals search engine 321
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(8)Gearbox support shaft nut: 6,5 ± 0,6
(9) Screws fixing gearbox support on body: 1,9 ± 0,1
(10)Gearbox support plate nut: 2,5 ± 0,2
(11)Nut fixing gearbox support on body: 1,9 ± 0,1
(12)Nut securing rubber bush: 3 ± 0,3
B2CP3ZKC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 321

Downloaded from www.Manualslib.com manuals search engine 324
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(1)Air vent hole : 1,5 ± 0,2
(2)Reverse gear rocker switch shaft fixing nut: 4,5 ± 0,2
(3) Differential housing fixing nut: 1,5 ± 0,2
(4)Screw fixing
(Ø M10)differential housing: 5 ± 0,5
(5)Speedometer drive support: 1,5 ± 0,2
(6)Screw fixing
(Ø M7)differential housing: 1,5 ± 0,2
(7)Drain plug : 3,5 ± 0,2
(8)Level plug: 2,2 ± 0,2
(9)Screw fixing gearbox housing/clutch housing: 1,3 ± 0,2
(10) Screw fixing 5th gear housing: 1,5 ± 0,2
(11)Reverse gear switch: 2,5 ± 0,2
B2CP3ZXD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 324

Downloaded from www.Manualslib.com manuals search engine 325
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(12)Fork shaft stop screw: 1,5 ± 0,2
(13)Differential gearwheel fixing screw: 6 ± 0,5
(14)Bearing stop screw: 1,5 ± 0,2
(15)Secondary shaft nut: 6,5 ± 0,5
(16)Primary shaft nut: 7,3 ± 0,5
(17)Gear control support fixing screw: 1,5 ± 0,2
B2CP3ZZC
B2CP3ZYD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 325

Downloaded from www.Manualslib.com manuals search engine 326
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: RFN - RFK - 9HX - 9HY - 9HZ
Tightening torques (m.daN).
(18)Stop guide screw: 1,25 ± 0,2
(19)Speedometer fixing screw: 1,5 ± 0,2
(20) Gearbox support shaft nut : 6,5 ± 0,6
(21)Nuts fixing rubber support: 3 ± 0,2
(22) Gearbox rubber support shaft: 5 ± 0,5
(23)Screw M10fixing the engine/gearbox housing support: 6 ± 0,5
(24) Screws M10fixing the engine/gearbox housing support: 3 ± 0,3
B2CP401C
B2CP400C
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 326

Downloaded from www.Manualslib.com manuals search engine 330
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: ML6 GEARBOX
Engine: RHR
B2CP3ZNC
Tightening torques (m.daN).
(13)Screws/nuts fixing the gearbox support: 4,5 ± 0,4
(14)Screw fixing the rubber bush: 3 ± 0,3
(15) Nut fixing the gearbox casing: 6,5 ± 0,6
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 330

Downloaded from www.Manualslib.com manuals search engine 333
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX CONTROLS
Engines: KFU - NFU
Features.
Unlocking a sleeve stop:
- Press on the tabs of the clip (6)at «b», using a flat screwdriver.
- Disengage the sleeve stops from their supports by pulling upwards.
B2CP3ZFD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 333