Citroen C4 2014.5 2.G Owner's Manual

219
Breakdown related to a lack of AdBlue® additive
When switching on the ignition, the SERVICE warning   lamp   comes   on   and   the   UREA  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   temporary   display   in   the  
i

nstrument   panel   of   "NO   START   IN"   and  
0
  km   or   miles   -   ("NO   START   IN   0   miles"   means  
"

Starting
 p
revented").
The
 Ad

Blue
® tank is  empty:  t he  s ystem  r equired  b
y
 
regulations   prevents   engine   starting.
Remaining range between 0 and 350 miles (0 and 600 km)
When switching on the ignition, the SERVICE warning   lamp   comes   on   and   the   UREA  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   temporary   display   in  
t

he   instrument   panel   of   "NO   START   IN"   and  
a

  distance   indicating   the   remaining   range  
e

xpressed   in   miles   or   kilometres   before  
e

ngine   starting   is   prevented   -   (For   example  
"

NO START   IN   350   miles"   means   "Starting   will  
b

e   prevented   in   350   miles).
When
  driving,   this   display   appears   every  
3

0   seconds   until   the   additive   tank   has   been  
t

opped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
w

orkshop   to   have   the   AdBlue
® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
ot

her wise you will not be able to restart your
engine. To
  be   able   to   start   the   engine,  
w

e   recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop   for   the   top-up   required.   If  
y

ou   carry   out   the   top-up   yourself,   it   is  
e

ssential   to   add   at   least   3.8   litres   of  
Ad

Blue
® to the additive tank.
R
efer
 
to
  the   "Topping-up"   section.
10
Checks

220
In the event of a fault with the the SCR emissions control system
In the event of the detection
of a fault
The  UREA,   SERVICE   and   diagnostic   warning  
l

amps   comes   on,   accompanied   by   an   audible  
s

ignal   and   the   display   of   the   message  
"

Emissions
 f
ault".
The
  alert   is   triggered   when   driving,   when  
t

he   fault   is   detected   for   the   first   time,   then  
w

hen   switching   on   the   ignition   for   subsequent  
j

ourneys,   while   the   fault   persists.During an authorised driving phase
(between 650 miles and 0 miles) (1 100 km and 0 km)
If a fault with the SCR system is confirmed ( after   30   miles   (50   km)   covered   with   the  
p

ermanent   display   of   the   message   signalling  
a

  fault),   the   SERVICE   and   engine   diagnostic  
w

arning   lamps   come   on   and   the   UREA  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   temporary   display   in  
t

he   instrument   panel   of   "NO   START   IN"   and  
a

  distance,   indicating   the   remaining   range  
e

xpress   in   miles   or   kilometres   before   engine  
s

tarting   is   prevented   -   (e.g.:   "NO   START   IN  
350
  miles"   means   "Starting   will   be   prevented  
in
  350   miles").
A
 
system
 
that
 
prevents
 
engine
 
starting
 
is
 
activated   automatically   from   650   miles   (1   100   km)   after   confirmation   of   a   fault   with   the   SCR   emissions  
c

ontrol
 
system.
 
Have
 
the
 
system
 
checked
 
by
 
a   CITROËN   dealer   or   a   qualified   workshop   as   soon   as   possible.
If
 
it
 
is
 
a
 
temporary
 
fault,
 
the
 
alert
 
d

isappears
 
during
 
the
 
next
 
journey,
 
a

fter
 
a
 
self
 
diagnosis
 
test
 
of
 
the
 
SCR
 
e

missions
 
control
 
system. While
  driving,   this   display   appears   every  
30   seconds   while   the   fault   with   the   SCR   system  
p

ersists.
The
  alert   is   repeated   when   switching   on   the  
ig

nition.
You
  should   go   to   a   CITROËN   dealer   or   a  
q

ualified   workshop   as   soon   as   possible.
ot

her wise, you will not be able to restart your
engine.
Checks

221
Starting prevented
Every  time   the   ignition   is   switched   on,   the  
S

ERVICE   and   engine   diagnostic   warning  
l

amps   come   on   and   the   UREA   warning   lamp  
f

lashes,   accompanied   by   the   temporary   display  
o

f   "NO   START   IN"   and   0   miles   or   kilometres -  
(

"NO   START   IN   0   miles"   means   "Starting  
p

revented").
To
  be   able   to   start   the   engine,   you   must   call   on  
a

  CITROËN   dealer   or   a   qualified   workshop.
You
  have   exceeded   the   authorised  
d

riving   limit:   the   starting   prevention  
s

ystem   inhibits   engine   starting.Freezing of the AdBlue® additive
The
 
AdBlue
® additive freezes at t
emperatures   below   around   -11°C.
The
 
SCR
 
system   includes   a   heater  
f

or
 
the
 
AdBlue
® tank, allowing you to c
ontinue
 
driving   in   very   cold   conditions.
10
Checks

222
Topping-up the AdBlue® additive
Precautions in use
Use only AdBlue® additive that meets the I
SO 22241
 
standard.
The
 
supply
 
in
 
a
 
non-drip   bottle   simplifies  
t

oping-up.
 
You
 
can   obtain   1.89   litre   (half   a   US  
g

allon)
 
bottles
 
from   a   CITROËN dealer   or   a  
q

ualified
 w

orkshop.
Keep
 
AdBlue
® out of the reach of
children,
 
in
 
its
  original   bottle.
Never
 
transfer   AdBlue
® to another
container:
 
it
 
would
 
loose   its   purity. Never
  dilute   the   additive   with   water.
Never   pour   the   additive   into   the   Diesel  
f

uel   tank.
Never   top-up   from   an   AdBlue®
dispenser
 
reserved
 
for
 
heavy
 
goods  
v

ehicles.
Filling
 
the
 
AdBlue
® tank is an operation i
ncluded
 
in
 
every
 
routine   service   on   your  
v

ehicle
 
by
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop.
Nevertheless,
 
given   the   capacity   of   the   tank,  
i

t
 
may
 
be
 
necessary   to   top-up   the   additive  
b

etween
 
services,
  more   particularly   if   an   alert  
(

warning
 
lamps
 
and   a   message)   signals   the  
r

equirement.
You
 
can
 
got
 
to
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop.
If
 
you
 
envisage
 
topping-up   yourself,   please  
r

ead
 
the
 
following
 
warnings   carefully. The
  AdBlue
® additive is an urea-based s
olution.
 
This   liquid   is   non-flammable,  
c

olourless
 
and   odourless   (kept   in   a   cool   area).
In
 
the
 
event
 
of   contact   with   the   skin,   wash  
t

he
 
affected
 
area   with   soap   and   water.   In   the  
e

vent
 
of
 
contact   with   the   eyes,   wash   (irrigate)  
t

he
 
eyes
 
with   large   amounts   of   water   or   with  
a

n
 
eye
 
wash
  solution   for   at   least   15   minutes.  
I

f
 
a
 
burning
 
sensation   or   irritation   persists,   get  
m

edical
 
attention.
If
 
swallowed,   immediately   wash   out   the   mouth  
w

ith
 
clean
 
water   and   then   drink   plenty   of   water.
In
 
certain
 
conditions   (high   ambient  
t

emperature,
  for   example),   the   risk   of   release  
o

f
 
ammonia
 
cannot   be   excluded:   do   not   inhale  
t

he
 
product.
 
Ammonia   vapour   has   en   irritant  
e

ffect
 
on
 
mucous   membranes   (eyes,   nose   and  
t

hroat).
Checks

223
Recommendations on storage Procedure
F Switch  off   the   ignition   and   remove   the  k
ey,   or   if   your   vehicle   has   one,   press   the  
S

TART/STOP   button   to   switch   off   the  
e

ngine. F

R
aise the boot floor for access to the
AdBlue
® tank. S
ecure
 
the   boot   floor   by   attaching   its   cord  
t

o
 
the
 
hook   on   the   parcel   shelf   support.
F
 
U

nclip
 
the   black   plastic   blanking   plug   using  
i

ts
 
tab.
F
 
I

nsert
 
your   fingers   into   the   aperture   and  
t

urn
 
the
 
blue   cap   a   6
th of a turn anti-
c
lockwise.
F
 
C

arefully
 
lift
 
off
 
the
 
cap,   without   dropping   it.
Never
 
store
 
bottles
 
of
 
AdBlue
® in your
vehicle. Before
  topping-up,   ensure   that   the   vehicle   is  
p

arked   on   a   flat   and   level   sur face.
In   wintry   conditions,   ensure   that   the  
t

emperature   of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer
 
area
 
for
 
a
 
few
 
hours
 
to
 
allow   the   top-up  
t

o
 
be
 
carried
 
out.
AdBlue
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat
 
bottles   be   stored   in   a   cool   area   and  
p

rotected   from   direct   sunlight.
Under
 
these   conditions,   the   additive   can   be  
k

ept
 
for
 
at   least   a   year.
If
 
the
 
additive   has   frozen,   can   be   used   once   it  
h

as
 
completely   thawed   out.
10
Checks

224
F Obtain  a   bottle   of   AdBlue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. F  
A
fter   emptying   the   bottle,   wipe   away   any  
s

pillage   around   the   tank   filler   using   a   damp  
c

loth.
F  
R
efit   the   blue   cap   to   the   tank   and   turn   it  
a
  6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   plastic   blanking   plug,  
c

lipping   it   in   on   the   flap
F
 
D

etach   the   cord   from   the   parcel   shelf  
s

upport   and   lower   the   boot   floor.
Important:
 
if
 
your
 
vehicle's
 
AdBlue®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
displays
 
and
  the  
i

mpossibility
 
of
 
starting
 
the
 
engine
 
-  
you
 
must
 
add
 
at
 
least
 
3.8 litres
 

(so
 
two
 
1.89
 
litre
 
bottles). If
  any   additive   is   split   or   splashed,   wash  
i

mmediately  
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If   the   additive   has   crystallised,   clean   it  
o

ff   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up
after a breakdown because of a lack
of additive ,   you   must   wait   around  
5   minutes   before   switching   on   the  
ig

nition,
 w
ithout opening the
driver's door, locking the vehicle,
introducing the key into the ignition
switch, or introducing the key of the
"Keyless Entr y and Star ting" system
into the passenger compartment .
Switch   on   the   ignition,   then,   after  
10   seconds,   start   the   engine.
Never   dispose   of   AdBlue
® additive b
ottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
Checks

225
Temporary puncture r epair k it
Access to the kit
This kit is  installed  i n  t he  s torage  b ox,  u nder  t he  b
oot   floor. A.
 "

Sealant"   or   "Air"   position   selector.
B.
on "
I"
 
/   off   "O"
 s
witch.
C.
 D
eflation   button.
D.
 P
ressure   gauge   (in   bar   and   p.s.i.).
E.
 C
ompartment
 h
ousing:
-  
a
  cable   with   adaptor   for   12   V   socket,
-  
v
arious   inflation   adaptors   for  
a

ccessories, such as balls, bicycle
tyres...
Description of the kit
F. Sealant c artridge.
G. W hite   pipe   with   cap   for   repair.
H.
 B

lack   pipe   for   inflation.
I.
 S

peed   limit   sticker.
Complete
 
system
 
consisting
 
of
 
a
 
compressor
 
a

nd
 
a
 
sealant
 
cartridge
 
which
 
permits
 
t

emporary repair
of a tyre so that you can
drive
 
to
 
the
 
nearest
 
garage.
It
 
is
 
designed
 
to
 
repair
 
most
 
punctures
 
which
 
c

ould
 
affect
 
the
 
tyre,
 
located
 
on
 
the
 
tyre
 
tread
 
o

r
 
shoulder.
The
 
vehicle's
 
electric
 
system
 
allows
 
the
 
c

onnection
 
of
 
a
 
compressor
 
for
 
long
 
e

nough
 
to
 
inflate
 
a
 
tyre
 
after
 
a
 
puncture
 
r

epair
 
or
 
for
 
inflating
 
a
 
small
 
inflatable
 
a

ccessory. The
  speed   limit   sticker   I   must   be   affixed  
t

o   the   vehicle's   steering   wheel   to   remind  
y

ou   that   a   wheel   is   in   temporary   use.
Do
  not   exceed   a   speed   of   50 mph  
(

80 km/h)   when   driving   with   a   tyre  
r

epaired   using   this   type   of   kit.
11
Practical information

226
Repair procedure
F Switch  off   the   ignition.
1. Sealing
F Uncoil  the   white   pipe   G  f ully.
F  U nscrew   the   cap   from   the   white   pipe.
F

C
onnect the white pipe to the valve of the
tyre
  to   be   repaired. F
 C onnect   the   compressor's   electric   plug   to  t
he   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   and   leave   the   engine  
r

unning.
F

T

urn the selector A to the
"sealant"
 p

osition.
F
 
C

heck
 
that
 
the
 
switch
 
B is in
position "O" .
Take
  care,   this   product   is   harmful   (e.g.
 e

thylene-glycol,   colophony...)   if   swallowed
 a

nd   causes   irritation   to   the   eyes.
Keep
  this   product   out   of   the   reach   of
 c

hildren.
Avoid
 
removing
 
any
 
foreign
 
bodies
 
w

hich
 
have
 
penetrated
 
into
 
the
 
tyre. Do
  not   start   the   compressor   before  
c

onnecting   the   white   pipe   to   the   tyre  
v

alve:   the   sealant   product   would   be  
e

xpelled   through   the   pipe.
Practical information

227
F Switch  on   the   compressor   by   moving  t
he switch B to position "I" until the tyre
pressure
  reaches   2.0   bars.
 T

he   sealant   is   injected   into   the   tyre   under  
p

ressure;   do   not   disconnect   the   pipe   from  
t

he   valve   during   this   operation   (risk   of  
sp

lashing). F
 R emove   the   kit   and   screw   the   cap   back   on  t
he   white   pipe.
 T

ake   care   to   avoid   staining   your   vehicle  
w

ith   traces   of   fluid.   Keep   the   kit   to   hand.
F
 
D
rive   immediately   for   approximately  
t

hree   miles   (five   kilometres),   at   reduced  
s

peed   (between   15   and   35 mph   (20   and  
6

0 km/h)),   to   plug   the   puncture.
F
 
S
top   to   check   the   repair   and   the   tyre  
p

ressure   using   the   kit.
If
  after   around   5   to   7   minutes   the  
p

ressure   is   not   attained,   this   indicates  
t

hat   the   tyre   is   not   repairable;   contact  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop   for   assistance.Tyre under-inflation detection
If the vehicle is fitted with tyre under-
i nflation   detection,   the   under-inflation w

arning   lamp   will   remain   on   after   the
 w

heel   has   been   repaired   until   the   system
 i

s   reinitialised   by   a   CITROËN   dealer   or   a
 q

ualified
 w
orkshop.
11
Practical information

228
F Connect  the   compressor's   electric   plug   to  t
he   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   again   and   leave   the  
e

ngine
 r
unning.
F
T
urn the selector A to the "air"
position.
F
 
U

ncoil
 
the
 
black
 
pipe
 
H
 
f

ully.
F
 
C

onnect
 
the
 
black
 
pipe
 
to
 
the
 
v

alve
 
of
 
the
 
wheel.
2. Inflation
F Adjust   the   pressure   using   the   compressor  (
to   inflate:   switch   B in position "I";
  to  
d

eflate:   switch   B in
p
osition "O"
 
and   press  
b

utton C ),
  in   accordance   with   the   vehicle's  
t

yre   pressure   label   (located   on   the   left  
h

and   door   aperture).  
 
A

  loss   of   pressure   indicates   that   the  
p

uncture   has   not   been   fully   plugged;  
c

ontact   a   CITROËN   dealer   or   qualified  
w

orkshop   for   assistance.
F
 
R
emove   and   stow   the   kit.
F
 
D
rive   at   reduced   speed   (50   mph   [80   km/h]  
m

ax)   limiting   the   distance   travelled   to  
a

pproximately   120   miles   (200   km).
As
 
soon
 
as
 
possible,
 
go
 
to
 
a
 
CITROËN
 
d

ealer
 
or
 
a
 
qualified
 
workshop.
You
 
must
 
inform
 
the
 
technician
 
that
 
you
 
h

ave
 
used
 
this
 
kit.
 
After
 
inspection,
 
the
 
t

echnician
 
will
 
advise
 
you
 
on
 
whether
 
t

he
 
tyre
 
can
 
be
 
repaired
 
or
 
if
 
it
 
must
 
be
 
r

eplaced.
Practical information