lock CITROEN C4 2018 Owner's Manual

117
C4-cactus_en_Chap05_securite_ed01-2016
Child seats
Recommendations
Installing a booster
cushion
The chest part of the seat belt must be positioned   on   the   child's   shoulder   without  
t

ouching   the   neck.
Ensure that the lap part of the seat belt
passes
  correctly   over   the   child's   thighs.
CITROËN
  recommends   the   use   of   a   booster  
s

eat   which   has   a   back,   fitted   with   a   seat   belt  
g

uide   at   shoulder   level.
As
  a   safety   precaution,   do   not   leave:
-
 
o
ne   or   more   children   alone   and  
u

nsupervised in a vehicle,
-
 
a
  child   or   an   animal   in   a   vehicle   which  
i

s   exposed   to   the   sun,   with   the   windows  
c

losed,
-
 
t
he   keys   within   reach   of   children   inside  
t

he   vehicle.
To
  prevent   accidental   opening   of   the   doors,  
u

se   the   child   lock.
Take
  care   not   to   open   the   rear   windows   by  
m

ore   than   one   third.
To
  protect   young   children   from   the   rays   of  
t

he   sun,   fit   side   blinds   on   the   rear   windows.
Children at the front
For optimum installation o f t he fo rward f acing c
hild   seat,   ensure   that   the   back   of   the   child  
s

eat   is   as   close   as   possible   to   the   backrest  
o

f   the   vehicle's   seat,   or   in   contact   if   possible.
The
  head   restraint   must   be   removed   before  
i

nstalling   a   child   seat   with   a   backrest   on   the  
p

assenger
 sea
t.
Ensure that the head restraint is stowed or
attached securely so that it is not thrown
around the vehicle in the event of sharp
braking.
Refit the head restraint as soon as the child
seat
  is   removed.
The
  legislation   on   carrying   a   child   on   the  
f

ront   passenger   seat   is   specific   to   each  
c

ountry.   Refer   to   the   legislation   in   force   in  
t

he   country   in   which   you   are   driving.
Deactivate
  the   passenger's   front   airbag  
w

hen   a   rear ward   facing   child   seat   is   installed  
o

n   the   front   passenger   seat.   Other wise,   the  
c

hild   would   risk   being   seriously   injured   or  
k

illed   if   the   airbag   were   deployed.
The incorrect installation of a child seat in a
vehicle
 
compromises
 
the
 
child's
 
protection
 
in
 
t

he
 
event
 
of
 
an
 
accident.
Check
 
that
 
there
 
is
 
no
 
seat
 
belt
 
or
 
seat
 
belt
 
b

uckle
 
under
 
the
 
child
 
seat
 
as
 
this
 
could
 
de

stabilise
 i

t.
Remember
 
to
 
fasten
 
the
 
seat
 
belts
 
or
 
the
 
c

hild seat harnesses keeping the slack in
relation
 
to
 
the
 
child's
 
body
 
to a minimum ,
even
 
for
 
short
 
journeys.
For
 
the
 
installation
 
of
 
a
 
child
 
seat
 
using
 
a
 
s

eat belt, ensure that this is well tensioned
on
 
the
 
child
 
seat
 
and
 
that
 
it
 
is
 
holding
 
the
 
c

hild
 
seat
 
firmly
 
against
 
the
 
seat
 
of
 
your
 
v

ehicle.
 
If
 
your
 
front
 
passenger
 
seat
 
is
 
a

djustable,
 
move
 
it
 
for ward
 
if
 
necessary.
At the rear seats, always leave sufficient
space
 
between
 
the
 
front
 
seat
 
and:
-
 
a

 
rear ward
 
facing
 
child
 
seat,
-

t

he feet of a child seated in a for ward
facing
 
child
 
seat.
For
 
this,
 
move
 
the
 
front
 
seat
 
for ward
 
and
 
if
 
n

ecessary
 
straighten
 
its
 
backrest.
5
Safety

118
C4-cactus_en_Chap05_securite_ed01-2016
Manual child lock
Locking
F With  the   ignition   key,   turn   the   red   control  o
ne   quarter   of   a   turn:
-
 
t
o   the   right   on   the   left-hand   rear   door,
-
 
t
o   the   left   on   the   right-hand   rear   door.
Unlocking
F With  the   ignition   key,   turn   the   red   control  o
ne   quarter   of   a   turn:
-

t
o the left on the left-hand rear door,
-
 
t
o   the   right   on   the   right-hand   rear   door.
Mechanical
  system   to   prevent   opening   of   the   rear   door   using   its   interior   control.
The   control   is   located   on   the   edge   of   each   rear   door.
Safety

121
C4-cactus_en_Chap06_conduite_ed01-2016
Starting
The parking brake must be applied.
F
 
W

ith
 
a   manual   gearbox,   place   the   gear  
l

ever in neutral then depress the clutch
pedal
 f

ully.
F
 
W

ith
 
an   electronic   gearbox,   place   the  
c

ontrol at N   then   press   the   brake   pedal  
f

i r m l y.
F
 
I

nsert
  the   key   into   the   ignition   switch;   the  
s

ystem   recognises   the   code.
F
 
U

nlock   the   steering   column   by   simultaneously
 t

urning   the   steering   and   the   key.
In
 
certain   cases,   you   may   have   to   apply  
m

ore   force   to   the   steering   (wheels   on  
f

ull
  lock,   for   example).
F
 
W

ith
 
a   petrol   engine,   operate   the   starter  
m

otor
  by   turning   the   key   to   position   3
without
  pressing   the   accelerator   pedal,  
u

ntil
 
the   engine   starts.   Once   the   engine   is  
r

unning,   release   the   key.
Starting-switching off the engine
It has 3 positions:
- position 1 (Stop):
  insert   and   removing  
the
  key,
-
position 2 (Ignition on) :
  steering   column  
u

nlocked,   ignition   on,   Diesel   preheating,  
e

ngine
 r
unning,
-
position 3 (Starting) .
Ignition switch
Switching off the engine leads to a loss o
f   braking   assistance.
Ignition on position (2)
It allows the use of the vehicle's electric equipment   or   portable   devices   to   be   charged.
Once
  the   state   of   charge   of   the   battery   drops  
t

o   the   reserve   level,   the   system   switches   to  
e

nergy   economy   mode:   the   power   supply   is  
c

ut   off   automatically   to   preserve   the   remaining  
b

attery   charge.
Avoid
  attaching   heavy   objects   to   the  
k

ey,   which   would   weigh   down   on   its  
b

lade   in   the   ignition   switch   and   could  
c

ause   a   malfunction.
It
  could   adversely   affect   the   deployment  
o

f   the   front   airbag.
6
Driving

123
C4-cactus_en_Chap06_conduite_ed01-2016
Key left in the "Ignition on" position
If the key has been left in the ignition switch at position 2 (Ignition on) ,
the
  ignition   will   be   switched   off  
a

utomatically   after   one   hour.
To
  switch   the   ignition   back   on,   turn   the  
k

ey   to   position   1 (Stop),
  then   back   to  
p

osition 2 (Ignition on) .
Never
 
switch
 
off
 
the
 
ignition
 
before
 
the
 
v

ehicle
 
is
 
at
 
a
 
complete
 
stop.
With
 
the
 
engine
 
off,
 
the
 
braking
 
and
 
s

teering
 
assistance
 
systems
 
are
 
also
 
c

ut
 
off:
 
risk
 
of
 
loss
 
of
 
control
 
of
 
the
 
v

ehicle.
When
 
you
 
leave
 
the
 
vehicle,
 
keep
 
the
 
k

ey
 
with
 
you
 
and
 
lock
 
the
 
vehicle.
To
 
facilitate
 
unlocking
 
of
 
the
 
steering
 c

olumn,
 
it
 
is
 
recommended
 
that
 
the
 w

heels
 
be
 
returned
 
to
 
the
 
straight
 
ahead
 p

osition
 
before
 
switching
 
off
 
the
 
engine.
Switching off
F Stop
  the   vehicle.
F  W ith   the   engine   running   at   idle,   turn   the   key  
t

o position 1 .
F
 
R
emove   the   key   from   the   ignition   switch.
F
 
T
o   lock   the   steering   column,   turn   the  
s

teering   until   it   locks.
F
 
C
heck   that   the   parking   brake   is   correctly  
a

pplied,   particularly   on   sloping   ground.For
  more   information,   refer   to   the  
"

Energy   economy   mode"   section.Energy economy mode
After switching off the engine (position 1- Stop),
for   a   maximum   of   30   minutes   you   can   still   use  
f

unctions   such   as   the   audio   and   telematic  
s

ystem,   the   wipers,   dipped   beam   headlamps,  
c

ourtesy   lamps,   ...
6
Driving

180
C4-cactus_en_Chap07_info-pratiques_ed01-2016
Recommendations on storage
Never store bottles of AdBlue® in your
vehicle.
Procedure
F Switch   off   the   ignition   and   remove   the   key.
F
F
or access to the AdBlue
® tank, raise the b
oot
 
carpet
 
then,
 
depending   on   equipment,  
l

ift
 
out
 
the
 
spare
 
wheel
 
and/or   the  
s

torage box. F
 
W
ithout   pressing,   turn   the   black   cap   a  
q

uarter   turn   anti-clockwise   and   lift   it   off.
AdBlue
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under these conditions, the additive can be
kept
 
for
 
at   least   a   year.
If the additive has frozen, it can be used once it
has
 
completely   thawed   out. Before
  topping-up,   ensure   that   the   vehicle   is  p
arked   on   a   flat   and   level   sur face.
In wintry conditions, ensure that the
temperature
  of   the   vehicle   is   above   -11°C.  
O

therwise the AdBlue
® may be frozen and s
o
 
cannot
 
be
 
poured
 
into   its   tank.   Park   your  
v

ehicle
 
in
 
a
 
warmer
 
area   for   a   few   hours   to  
a

llow
 
the
 
top-up
 
to
 
be
 
carried   out.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F
 
L

ift
 
off
 
the
 
cap.
Practical information

181
C4-cactus_en_Chap07_info-pratiques_ed01-2016
F Obtain a bottle of AdBlue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank.
I
mportant :
 
if
 
your   vehicle's   AdBlue
®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
messages
 
and  
t

he
 
impossibility
 
of
 
starting
 
the
 
engine,  
y

ou
 
must
 
add
 
at
 
least
 
3.8
 
litres
 
(so
 
t

wo 1.89
 
litre
 
bottles). If any additive is split or splashed, wash
immediately
 
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up
after a breakdown because of a lack
of additive ,   signalled   by   the   message
 "

Top   up   emissions   additive:   Starting
 p

revented",   you   must   wait   around
 5

 minutes
 
before
 
switching
 
on
 
the
 
ignition,
 w

ithout opening the driver's door,
locking the vehicle or introducing the
key into the ignition switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
Never dispose of AdBlue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a
 
6th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat the indicator on the cap lines up with
the
  indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
  the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.
7
Practical information

193
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does not block   traffic:   the   ground   must   be   level,  
s

table   and   not   slippery.
Apply
  the   parking   brake,   switch   off   the  
i

gnition   and   engage   first   gear   to   block  
t

he   wheels.
Check
  that   the   parking   brake   warning  
l

amps   in   the   instrument   panel   come   on.
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
Ensure
  that   the   jack   is   correctly  
p

ositioned   at   one   of   the   vehicle's  
j

acking   points.
Incorrect
  use   of   the   jack   could   cause  
t

he   vehicle   to   drop.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
List of operations
F Remove  the   wheel   bolt   cover(s)   using   the  t
ool 3   (depending   on   version).
F
 
S
lacken   the   bolts   using   the  
w

heelbrace

1 o n l y.
Do
  not   use:
-
 
t
he   jack   for   any   other   purpose   than  
l

ifting   the   vehicle,
-
 
a
  jack   other   than   the   one   supplied  
b

y   the   manufacturer. The
  jack   must   only   be   used   to   change   a  
w

heel   with   a   damaged   tyre.
The   jack   does   not   require   any  m
aintenance.
The
  jack   conforms   to   European  
l

egislation,   such   as   defined   in   the  
M

achinery   Directive   2006/42/CE.
8
In the event of a breakdown

199
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Main beam headlamps
F Remove  the   protective   cover   by   pulling   the  t
ab.
F

D
isconnect the bulb connector (do not
remove
 t

he
 e
arth
 c
onnector
 lo
cated
 belo
w).
F
 
P
ush   on   the   spring,   then   move   it   towards  
t

he   middle   of   the   vehicle   to   release  
t

he bulb.
F
 
R
emove   the   bulb   and   change   it.
Direction indicators
Amber coloured bulbs, such as the direction   indicators,   must   be   replaced  
w

ith bulbs of identical specifications
and
  colour.
Rapid
 
flashing
 
of
 
the
 
direction
 
indicator
 w
arning
 
lamp
 
(right
 
or
 
left)
 
indicates
 
the
 
f

ailure
 
of
 
a
 
bulb
 
on
 
that
 
side.
F
 
T

urn
 
the
 
bulb
 
holder
 
an
 
eighth
 
of
 
a
 
turn
 
a

nti-clockwise
 
and
 
extract
 
it.
F
 
R

emove
 
the
 
bulb
 
and
 
change
 
it.
To
 
reassemble,
 
carry
 
out
 
these
 
operations
 
in
 
r

everse
 o

rder. To
 
reassemble,
 
carry
 
out
 
these
 
operations
 
in
 
r

everse
 o

rder.
8
In the event of a breakdown

202
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
1. Sidelamps (W5W).
2. B rake   lamps   (P21W).
3.
 D

irection   indicators   (PY21W).
4.
 F

oglamp   or   reversing   lamp   (P21W).
Rear lamps
Changing bulbs
To reassemble, carry out these operations in reverse o rder.
F

S
pread the bulb holder retainers and
remove   the   bulb   holder.
F  
R
eplace   the   failed   bulb:
-  
f
or   the   sidelamp,   pull   the   bulb   (the   upper  
o

n e) o u t ,
-  
f
or   the   other   lamps,   turn   the  
c

orresponding   bulb   (lower)   a   quarter  
t

urn.
These
 
bulbs
 
are
 
changed
 
from
 
inside
 
the
 
boot.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
corresponding
 
access
 
cover
 
in
 
t

he
 
trim
 
panel.
F
 
D

isconnect
 
the
 
lamp
 
unit
 
connector
 
a by
pressing
 
the
 
locking
 
button
 
(located
 
under
 
t

he
 
connector
 
for
 
the
 
right
 
hand
 
lamp
 
a

nd above the connector for the left hand
lamp),
F
 S
lacken
 
and
 
remove
 
the
 
nut
 
b ( take care
not to drop it inside the wing ).
F
 
P

ress
 
down
 
on
 
the
 
retaining
 
clip
 
for
 
lamp
 
u

nit c,
 
then
 
carefully
 
remove
 
it
 
towards
 
the
 
o

utside. Take
  care   to   engage   the   lamp   unit   in   its  
g

uides,   while   keeping   it   in   line   with   the  
v

ehicle.
Tighten
  sufficiently   to   ensure   sealing,  
b

ut   without   damaging   the   lamp.
In the event of a breakdown

208
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
FuseN° Rating
(A) Functions
F19 5Seat
  belt   unfastened   warning.
F20 5Airbags.
F21 5Instrument
  panel.
F22 30Locks.
F23 5Courtesy
  lamp,   map   reading   lamp.
F26 15Horn.
F27 15Front
  and   rear   screenwash.
F28 5Ignition
 s

witch.
F30 15Rear
  wiper.
In the event of a breakdown