Citroen C4 AIRCROSS 2014 1.G Owner's Manual

9
239
Te c h n i c a l d a t a




Dimensions (in mm)
These dimensions have been measured on a vehicle that is not loaded.





* Mirrors folded.

240
Te c h n i c a l d a t a
Off-road performance


Engine
Ground clearance *
A
Approach angle
Departure angle
Break-over angle
1.6 litre 115
190 mm

18.9 °
30.9 °
19.0 ° 2.0 litre 150
201 mm
1.6 litre HDi 110
178 mm
1.8 litre HDi 150
182 mm

*
Vehicle unladen.

9
241
Te c h n i c a l d a t a




















Identifi cation markings
Various visible markings for the identification and tracing of your vehicle.



A.
Manufacturer's plate.

It is riveted to the right hand middle pillar
and carries the following information:


- manufacturer,

- EU type approval number,

- vehicle identification number (VIN),

- gross vehicle weight,

- gross train weight,

- maximum front axle weight,

- maximum rear axle weight.
The tyre pressures must be checked
when the tyres are cold, at least once
a month.

If the tyre pressures are too low, this
increases fuel consumption.

B.
Ty r e l a b e l .

This label is affixed to the the driver's
side middle pillar and carries the following
information:


- tyre sizes,

- tyre pressures.
C.
Vehicle Identification Number (VIN)
under the bonnet.

This number is engraved on the bodywork
near the damper support.

242Te c h n i c a l d a t a

243

SPEAK
Press this button to activate voice recognition (" Listening
" is displayed).
During a voice recognition, press this button briefl y to put this voice recognition on hold.
Make a long press on this button to deactivate voice recognition.
Press this button briefl y to activate voice recognition, even during a call.










ANSWER A CALL
Press this button to accept an incoming call.
In the event of a 2
nd
incoming call, press
to put the 1 st call on hold and speak to the
second caller.
In this case, press briefl y to switch from one
call to the other.
To establish a three-way conversation,
press on SPEAK to change from voice
recognition and say " Incorporate the call
".

END CALL
Press this button to reject an incoming call.
During a conversation, press this button to
end the call.





BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

244




BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

By default, the voice recognition system is in English.

Press this button.
Say " Setup
".

Say " Language
".

Say the language of your choice in English, example: say
" French
" for French.

Say " Ye s
" to start the change of language process
Say " No
" to return to steps 4 to 7.
The system says " Select a language: English, Spanish, French,
German or Italian
".

The system then says " French selected. Is this correct?
"

The system repeats the language chosen and completes the
change of language process.

If you do not start the training procedure within around 3 minutes of
pressing SPEAK, the process is cancelled.
If you press SPEAK within 5 seconds following the play of a voice
command, this command is saved again.














What is the Bluetooth
®
hands-free telephone with voice
recognition?
The system uses wireless communication technology known as
Bluetooth
®
which allows you to make hands-free telephone calls in
your vehicle via your Bluetooth ® compatible mobile telephone.
You can make telephone calls using a microphone located in
the courtesy lamp, making use of the simple steering mounted
controls or by the voice recognition function with voice commands.
Five languages are available: English (the default), Spanish,
French, German and Italian.










Change the voice command language

245




BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION








Training the user's voice


You can use the user voice training function to create a voice model
for one person per language.
The characteristics of your voice and your pronunciation are saved
in this model to provide the best voice recognition.
The vehicle must be stationary with the parking brake applied.
Switch off your telephone during the operation to avoid any
interruption.

Press this button.
The system says the fi rst of 45 standard phrases.

Say " Word training
".
When you are ready to start, press and
hold this button.

Repeat each of the phrases in the table on the following
page.
The system saves your voice and moves on to the next
command.
Continue the process until all of the phrases have been
saved.

An explanation message is given.
After playing all the voice commands, the system says " The word

training
is complete
" and ends the process.

If you do not start the programming process within approximately
3 minutes after pressing the SPEAK button, the process is
cancelled.
If you press the SPEAK button within 5 seconds of the play of a
voice command, this command is saved again.

246




BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

Voice training commands

1 # 790 (for # = "Hash")
2 * 671 (for * = "Star")
3 212 - 4 903
4 235 - 3 494
5 315- 5 657
6 456 - 7 930
7 793 - 5 462
8 794 - 1 826
9 826 - 3 145
10 962 - 7 305
11 (531) 742 - 9 860
12 (632) 807 - 4 591
13 (800) 222 - 5 015
14 (888) 555 - 1 212
15 0 123 456 789 16 55 66 77 88 99
17 44 33 22 11 00
18 Call 293 - 5804
19 Call * 350
20 Call 1 (234) 567 - 8 901
21 Dial 639 - 1542
22 Dial # 780
23 Dial (987) 654 - 3210
24 1058# 3794# Send
25 27643# 4321# Send
26 Cancel
27 Continue
28 Emergency number
29 Clear all
30 Help 31 Home, Work, Mobile, Pager
32 List of names
33 No
34 Phone book: Delete

35 Phone book: New entry
36 Previous
37 Phone book: Clear all
38 Redial
39 Repeat the training
40 Confi gure the confi rmation requests
41 Confi gure the language
42 Confi gure the matching options
43 Match a telephone
44 Transfer the call
45 Yes

247




BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

For reasons of safety and because the sustained attention of the
driver is needed, operations of matching a Bluetooth ® mobile phone
with the audio system's hands-free function must be done with the
vehicle stationary
.

The systems says " Please say the 4 digits of a pairing cod

e
".

Press this button.

The system confi rms the validity of the number spoken,
answer " Ye s
".
Say " No
" to return to step 7.

Say " Pairing options
".










Pairing a Bluetooth ®
telephone
First connection


Say " Pair a telephone
".

Say " Confi gure
".
The system can register up to 7 Bluetooth
®
compatible mobile
telephones.
The telephone which has the highest level of priority is connected
automatically.

The system says " Do you wish to
pair
a telephone, delete a
telephone or obtain the list of paired telephones?
".
Say a 4-digit number which will be recorded as the pairing
code.

Remember this pairing code as you must enter it in the telephone in
one of the following steps of the matching procedure.

248

Consult your mobile telephone's user manual and enter
the pairing code recorded in step 7 in the telephone.





BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

The system says " Start the
pairing
procedure on the telephone.
Consult the instructions in the telephone manual
".

If the code is incorrect, the system locks. To clear the code:


- check that the telephone's voice recognition is not activated,

- with the ignition on and the audio system active, press the END
CALL button for 2 seconds, 3 times in succession.


When it detects a Bluetooth
®
compatible mobile telephone,
the system says " Please say the name of the telephone after
the beep
".

After the audible signal, allocate a name to the telephone
by saying the name of your choice.
The system says " Allocate an order of priority between 1 and 7.
One is the highest level of priority
".

Give a number between 1 and 7 to establish the level of
priority of the mobile telephone.

The system says and confi rms the " name of the telephone
" and
the " number
" of its priority.

Answer " Ye s
".
Say " No
" to return to step 13.

The systems says " Pairing complete
" then emits an audible signal
and deactivates the voice recognition.
The services available depend on the network, the SIM card and the compatibility of the Bluetooth
®
telephone used. Check in your telephone
user manual and with your service provider for the services you have access to.

If the system does not detect the Bluetooth
®
compatible mobile
telephone, the matching process stops ands is accompanied by an
audible signal.
If you select a level of priority which has already been allocated to
another telephone, the system asks you if you wish to replace this
level of priority.