turn signal Citroen C4 AIRCROSS 2014 1.G Owner's Manual

28
Monitoring










Operation indicator lamps

If one of the following indicator lamps comes on, this confirms that the corresponding system has come into operation.
It may be accompanied by an audible signal and a message in the instrument panel screen.



Warning lamp



is on



Cause



Action / Observations






Left-hand
direction
indicator


flashing with audible
warning. The lighting stalk has been pressed
downwards. If this indicator lamp flashes abnormally quickly, this
could indicate that the bulb of one of the direction
indicators has blown. Change the bulb or contact a
CITROËN dealer or a qualified workshop.





Right-hand
direction
indicator


flashing with audible
warning. The lighting stalk has been pushed
upwards. If this indicator lamp flashes abnormally quickly, this
could indicate that the bulb of one of the direction
indicators has blown. Change the bulb or contact a
CITROËN dealer or a qualified workshop.




Sidelamps
or
dipped beam
headlamps


fixed. The sidelamps or dipped beam
headlamps are on.




Main beam
headlamps


fixed. The lighting stalk is pulled towards
you. Pull the stalk to return to dipped beam headlamps.




Front foglamps


fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.




Rear foglamp


fixed. The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.

1
31
Monitoring








Instrument panel screen


Each time the engine is started: warning lamps and/or messages come on, applying a checking self test. They go off after a few seconds.


When you want to see the trip computer information, you can choose to ignore the alerts, by pressing the INFO
button on the dashboard.

The messages displayed may vary according to the type of display screen (type 1 or type 2) in the instrument panel.

Cer tain messages are only displayed in the type 2 screen.


When this symbol appears: make a
shor t press
. When this symbol appears: make
a long press
.

Ignition off.

Ignition on
(with a manual gearbox).

Ignition on
(with a CVT gearbox).



Warnings and alerts


When an alert occurs, the displayed information then disappears. the warning lamp and its associated message appear, accompanied if appropriate by
an audible signal.
When there are several alerts, they are displayed in turn and this symbol appears. It remains displayed while there are still alerts.
You will then be able to display the alerts again by pressing the INFO
button several times to cycle through the trip computer information and return to
the alerts.

1
61
Monitoring





Lighting dimmer


System for manual adjustment of the
brightness of the instruments and controls in
relation to the exterior brightness.
There is an audible signal and the
intensity of the lighting increases each
time the button is pressed.
With the lighting on or off, press the button
to change the intensity of the lighting of the
instruments and controls in "day" or "night"
mode.
When the lighting reaches the maximum
setting, press again to change to the minimum
setting.
When the lighting reaches the required
intensity, release the button.

With the vehicle's lighting off, only the
brightness of the instrument panel is modified.
The setting is saved when the ignition switch is
turned to OFF.

Wit the vehicle's lighting on, the brightness of
the entire dashboard (instrument panel, screen,
air conditioning control panel...) is modified.

69
2
Access





Emergency procedure with the Keyless Entry and Starting
system


Unlocking



)
Turn the key towards the front in the
driver's door lock to unlock the vehicle.



Emergency unlocking/locking
using the integral key
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:


- cell battery flat, vehicle battery discharged
or disconnected, ...

- vehicle located in an area with strong
electro-magnetic signals.


)
Pull and hold button 1
, to extract the
integral key 2
.


Locking



)
Turn the key towards the rear in the driver's
door lock to lock the vehicle.


The emergency key allows you to lock
or unlock the driver's door only.
To lock or unlock the other doors, use
the interior controls (see "Locking /
unlocking from inside").

135
5
Visibility


Model with a rear foglamp only

rear foglamp
Rotate and release the ring C
:


)
for wards a first time to switch on the front
foglamps,

)
for wards a second time to switch on the
rear foglamp,

)
rear wards a first time to switch off the rear
foglamp,

)
rear wards a second time to switch of the
front foglamps.






In good or rainy weather, both day
and night, the front foglamps and the
rear foglamps are prohibited. In these
situations, the power of their beams
may dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamps when
they are no longer necessary.








Model with front foglamps and
a rear foglamp

Foglamp selection ring
.
They operate if at least the sidelamps are on.


)
To switch on the rear foglamp, turn the
ring C
for wards.


)
To switch off the rear foglamp, turn the
ring C
rearwards.


front and rear foglamps


Lighting on reminder

An audible signal when the driver's door
is opened warns the driver if the vehicle
lighting is on, with the ignition off.
Switching off the lighting stops the
audible signal.

153
6
Safety
If the driver does not fasten their seat belt
within one minute after switching on the
ignition, the warning lamp flashes accompanied
by an intermittent audible signal and a display
on the instrument panel screen.
The warning lamp, the audible signal and the
display stop after approximately 90 seconds
and return until the driver fastens their
seat belt.
If the seat belt is unfastened while the vehicle
is moving
, you are alerted by the same
warnings. When the ignition is switched
on, this warning lamp comes on
accompanied by an audible signal for
a few seconds if the driver has not
fastened their seat belt.

Front seat belt not fastened /
unfastened warning lamp

Front passenger's seat belt
Driver's seat belt

When the ignition is switched on, this
warning lamp comes on the centre
console panel.
It is accompanied by an audible signal for a few
seconds if the passenger has not fastened their
seat belt.
If the seat belt is unfastened while the vehicle
is moving
, you are alerted by the same
warnings.

248

Consult your mobile telephone's user manual and enter
the pairing code recorded in step 7 in the telephone.





BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

The system says " Start the
pairing
procedure on the telephone.
Consult the instructions in the telephone manual
".

If the code is incorrect, the system locks. To clear the code:


- check that the telephone's voice recognition is not activated,

- with the ignition on and the audio system active, press the END
CALL button for 2 seconds, 3 times in succession.


When it detects a Bluetooth
®
compatible mobile telephone,
the system says " Please say the name of the telephone after
the beep
".

After the audible signal, allocate a name to the telephone
by saying the name of your choice.
The system says " Allocate an order of priority between 1 and 7.
One is the highest level of priority
".

Give a number between 1 and 7 to establish the level of
priority of the mobile telephone.

The system says and confi rms the " name of the telephone
" and
the " number
" of its priority.

Answer " Ye s
".
Say " No
" to return to step 13.

The systems says " Pairing complete
" then emits an audible signal
and deactivates the voice recognition.
The services available depend on the network, the SIM card and the compatibility of the Bluetooth
®
telephone used. Check in your telephone
user manual and with your service provider for the services you have access to.

If the system does not detect the Bluetooth
®
compatible mobile
telephone, the matching process stops ands is accompanied by an
audible signal.
If you select a level of priority which has already been allocated to
another telephone, the system asks you if you wish to replace this
level of priority.

327
05

CD-TEXT display


Press the DISP
button repeatedly; the
CD-Text information appears in the
following order:
DISC NAME / TRACK NAME /
NORMAL DISPLAY MODE.
The CD player is compatible with the display of CD-Text
information.

In the case of compact discs containing both CD-DA and MP3 fi les,
play automatically begins with the CD-DA fi les.
To switch play between the two types of fi le, press the CD
button for
more than two seconds until an audible signal is heard.
While using these compact discs, the "Repeat", "Random play" and
"Playing of the beginning of the tracks" functions are only applied to
fi les of the same format.
If the information exceeds
12 characters, press the PAGE
button
to see the rest.
In the absence of CD-Text information
to be displayed, "NOTITLE" appears
on the screen.








MP3 / ID3 Tag CD


Selecting an MP3 folder

Turn the SEL
knob to the right to
select a folder in ascending order or to
the left to select a folder in descending
order.
The CD player and the CD changer are compatible with the playing
of MP3 fi les.
These must be recorded in ISO-8859 Level 1 / Level 2, Joliet or
Romeo format on CD ROMs, CD-Rs or CD-RWs. The CDs can
contain a maximum of 255 fi les and 100 folders on 16 levels.
The ID3 version 1.0, 1.1, 2.2, 2.3 and 2.4 Tag can be displayed
while playing MP3 fi les.

MUSIC MEDIA PLAYERS