Citroen C4 DAG 2010 2.G Owner's Guide

Page 31 of 284

28
I
M O N I T O R I N G
5 seconds after the ignition is switched
on, the spanner is switched off ; the
distance recorder resumes its normal
operation. The display then indicates
the total and trip distances.
Less than 620 miles (1 000 km)
remain before the next service is due

Examples: 400 miles/900 km remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates: Service overdue
For 5 seconds after the ignition is
switched on,
the spanner fl ashes
to indicate that the service must be
carried out as soon as possible.

Example: the service is overdue by
300 miles/km.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation. The
spanner remains on to indicate that
a service must be carried out soon. 5 seconds after the ignition is
switched on, the distance recorder
resumes its normal operation.
The
spanner remains lit .
More than 620 miles (1 000 km)
remain before the next service is due
For 5 seconds after the ignition is
switched on, the spanner symbol-
ising the service operations comes
on. The distance recorder display
line indicates the distance remaining
before the next service is due.

Example: 4 800 miles/km remain
before the next service is due.
For 5 seconds after the ignition is
switched on, the display indicates:
The distance remaining may be
weighted by the time factor, depend-
ing on the driver's driving habits.
Therefore, the spanner may also
come on if you have exceeded the
two year service interval.

Page 32 of 284

29
I
M O N I T O R I N G
Service indicator zero reset Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct

Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essential
that the level is topped up to prevent
damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL

--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on the
dipstick:
- A = max; never exceed
this level,
- B = min; top up the lev-
el via the oil fi ller cap,
using the type of oil
suited to your engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

Page 33 of 284

30
I
M O N I T O R I N G
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other pe-
riod since it was reset to zero by the
driver.

 With the ignition on, press the
button until zeros appear. Dashboard lighting rheostat
Activation

 Turn control A or press control B
to adjust the brightness of the
dashboard lighting,

 With control B , press until the
brightness is at maximum, release,
press until you reach minimum.
Deactivation
When the vehicle lighting is off, or in
day mode in the case of vehicles fi t-
ted with daytime running lamps, the
button has no effect.
System permitting manual adjustment
of the brightness of the dashboard to
suit the level of ambient light.
The rheostat is active if the side-
lamps are on and applies to:
- the instrument panel,
- the display screens.

Page 34 of 284

31
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN A
Presentation

1. Time

2. Date and display zone

3. Ambient temperature
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
The display of certain types of in-
formation is sometimes by scrolling
and sometimes by alternating be-
tween them.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed in zone 2
(date, radio-CD and trip recorder)

B or F. Within the menus, choice
of activation/deactivation of
functions and selection of
adjustments
Controls Main Menu
By pressing button A , then using
button B , you have access to the fol-
lowing functions:


Page 35 of 284

32
II
M U L T I F U N C T I O N S C R E E N S Displaying the log of alerts

 Press on A .

 Use B to select the submenu for
options. Confi rm with two press-
es on C .
You can cancel the start of the display
by pressing button E to abandon and
confi rming by pressing C .
Alerts signalled previously but not
resolved, will scroll in the display for
recall.
To clear the displaying of an alert,
press D .
Adjusting the date and time

 Press on A .

 Use B to select the submenu for
display adjustments, then con-
fi rm by pressing C .

 Press B to select what you want
to modify: year, month, day, hour,
minutes, mode of display.

 Make your adjustment by press-
ing F . You can continue your
adjustments by selecting a dif-
ferent element by presses on

B . When you have fi nished your
adjustments, press C .
Configuring the vehicle
functions

 Press on A .

 Use B to select the sub-menu for
personalisation confi guration of
your vehicle, then confi rm your
choice with a press on C .

 Select the function to be confi g-
ured by pressing B .

 The system tells you whether
the function status is active or in-
active. Modify this status with a
press on F .

 Confi rm with a press on C . Choosing the language

 Press on A .

 Use B to select the submenu for
languages. Confi rm your choice
with a press on C .

 With presses on F , select the
language of your choice, then
confi rm with a press on C .
Choosing the units

 Press on A .

 Press B to select the sub-menu
for Units. Confi rm your choice
with a press on C .

 Press B to select the type of unit
you wish to modify (Temperature
or Fuel Consumption).

 With presses on F , select the
unit of your choice, then confi rm
with a press on C .
This choice concerns all the in-
formation (Consumption - Speed)
appearing on the display screens.

Page 36 of 284

33
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN C Main Menu
Presentation
Radio-CD
(see "Audio and
Telematics")
Trip computer
This permits:
Bluetooth
®
hands-free
system
(see "Audio and
Telematics")
Controls

1. Time

2. Ambient temperature

3. Date and display zone
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen (See
"Trip computer") Press button
A to view the "Main
Menu" of the multifunction screen.
This menu gives you access to the
following functions:
- entering the distance to your destination,
- access to the log of alerts (recall of alerts signalled previously),
- access to the status of functions, such as the activation/deactiva-
tion of the automatic illumination
of headlamps, of the automat-
ic rain sensitive wipers, of the
ESP...

Page 37 of 284

34
II
M U L T I F U N C T I O N S C R E E N S
Personalisation -
Configuration
This permits activation/deactivation
of the:
- automatic operation of the rear wiper when reverse gear is en-
gaged,
- automatic guide-me-home lighting,
- Xenon dual-function directional headlamps,
and selection of the:
- brightness intensity, time, date and units,
- screen language. Activating/deactivating the
rear screen wipe when you
engage reverse gear

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for ve-
hicle parameters. Confi rm your
choice with a press on C .

 Using B , select "parking assis-
tance". Confi rm your choice with
a press on C .

 Then by pressing C , select/de-
select "activation of rear wiper in
reverse gear" to activate/deacti-
vate this.

 Confi rm with "OK" on the screen.
Activating/deactivating the
automatic guide-me-home
lighting

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for ve-
hicle parameters. Confi rm your
choice with a press on C .
 Using B , select "lighting and
signalling". Confi rm your choice
with a press on C .

 Then by pressing C , select/de-
select "guide-me-home head-
lamps" to activate/deactivate
this. After activation, choose its
duration: press on C , then use

B to select the duration and then
press on C .

 Confi rm with "OK" on the
screen.
Activating/deactivating
the Xenon dual-function
directional headlamps

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for ve-
hicle parameters. Confi rm your
choice with a press on C .

 Using B , select "driving assis-
tance". Confi rm your choice with
a press on C .

 Then by pressing C , select/de-
select "directional headlamps" to
activate/deactivate them.

 Confi rm with "OK" on the screen.

Page 38 of 284

35
II
M U L T I F U N C T I O N S C R E E N S
Adjusting the date and time

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Select the display confi guration
using B . Confi rm with a press
on C .

 Select the adjustment for the
date and time, using B . Confi rm
with a press on C . Choosing the units

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Select the display confi guration
using B . Confi rm with a press
on C .

 Then select the sub-menu for
units. Confi rm your choice with a
press on C .

 Using B , select the unit you wish
to modify (Temperature or Fuel
consumption), then confi rm by
pressing C .

 Confi rm with "OK" on the
screen.
This choice concerns all the informa-
tion (Consumption - Speed) appearing
on the screens. Choosing the language

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Make your choice of language
using B . Confi rm with a press
on C .

 Using B , select the language and
confi rm your choice with a press
on C .

 Confi rm with "OK" on the screen.

 Press B to select the values you
wish to modify. Confi rm your
choice with a press on C .

 Make your adjustments by
pressing B , confi rming each ad-
justment choice by pressing C .

 Validate with "OK" on the
screen.

Page 39 of 284

36
II
M U L T I F U N C T I O N S C R E E N S
NAVIDRIVE MULTIFUNCTION SCREEN
Presentation

1. Ambient temperature

2. Directory

3. Date

4. Telephone

5. Time
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (risk of
ice).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion. Controls Main Menu

Traffi c Information

Navigation/Guidance

Map

Audio Functions

Telematics

Confi guration,
for adjusting various param-
eters (date, time, units)

Video

Vehicle Diagnostics

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Selection and confi rmation in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen.
This menu gives you access to the
following functions (see "NaviDrive
Instructions"):

Page 40 of 284

37
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current infor-
mation concerning the trip travelled
(range, fuel consumption...).
Monochrome screen A Information displays

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
fuel consumption and the aver-
age speed.
Zero reset
The trip computer provides the fol-
lowing information:
- range,
- current fuel consumption,
- distance travelled,
- average fuel consumption,
- average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wiper stalk , to display
the various items of trip comput-
er data in succession.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80 ... 290 next >