low beam Citroen C4 PICASSO 2008 1.G Owner's Manual

IN BRIEF
I
4
E X T E R I O R
Panoramic glass roof
Xenon directional headlamps
Whether on dipped beams or main beams, this func-tion allows your headlamps to follow the direction of the road ahead.
Opening rear screen
Pneumatic rear suspension
The rear pneumatic suspen-sion enhances driving comfort and maintains a constant body height whatever the vehicle load.
Exterior side lighters
These light up the zones fac-ing the driver’s and passen-ger’s doors.
Front/rear parking assistance
Sensors located in the bumpers detect obstacles.
Parking space sensor
Measures the size of a space and informs you of the possi-bility of parking.
Exterior rear view mirrors
With electric foldback.
Automatically tilts in reverse gear.

II
93
Function active
If there is a malfunction, a message informs you of this and the “Dipped beams” warning lamp fl ashes.
Have the system checked by a CITROËN dealer.
You are recommended to have both Xenon dual-function direction al headlamps changed if there has been a malfunction in either of them.
Function inactive
This function is associated with Xenon dual-function headlamps.
Whether on dipped beam or main beam, your headlamps follow the direction of the road ahead.
Lighting quality when driving round bends is considerably improved.
On vehicles equipped with day-time-running lamps (according to country), the function is acti-vated only if the lighting control is on main beam / dipped beam or AUTO (automatic lighting of head-lamps). If the control is in position 0, the function is not active.
Activation / Deactivation
The function can be activated / deactivated in the “Main men u”. See “Multifunction displays”.
When you start the engine, you retain the mode (activated or deactivated) that was selected when you last stopped the engine.
By default, this function is in activated mode.
Note : At zero or very low speed, or in reverse gear, this function is inactive.
D I R E C T I O N A L H E A D L A M P S

12
3
4
182
VIFRONT LENS
 Dipped beam
 Main beam
 Sidelamp
 Direction indicator
Note : A slight misting may appear on the internal sur-face of the headlamp glass in some climatic conditions (e.g. low temperature or humidity) ; this disappears af-ter the lamps have been on for a few minutes.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S
Dipped beam
1. Remove the rubber plug.
2. Rotate the bulb-holder a quarter turn anti-clockwise and remove it from its housing.
3. Replace the bulb H7.
4. Reposition the bulb-holder by pushing it in, tighte -ning it by a quarter turn (clockwise).
5. Put back the rubber plug.
Changing a halogen bulb should only be done after the headlamp has been switched off for a few minutes (risk of serious burns).
Do not touch the bulb directly with your fi ngers, use lint-fre e cloths.
It is imperative to use only anti-U.V. type bulbs in order not to damage the headlamp.
When using a high-pressure washer on persistant marks, do not direct at the lamps or their outlines for too long, so as not to damage their coating and their seals.

VI
183
Main beam
1. Remove the rubber plug.
2. Detach the clips by lowering them on each side of the bulb.
3. Pull on t he bulb- holder t o remove it.
4. Replace the bulb H1.
5. Push the bulb-holder back into its housing.
6. Reattach the clips.
7. Put back the rubber plug.
Sidelamp
1. Rotate the bulb-holder a quarter turn anti-clockwise.
2. Remove it from its housing.
3. Replace the bulb H6W.
4. Reposition the bulb-holder.
5. Rotate it a quarter turn clock-wise to reposition in its housing.
Direction indicator
1. The direction indicator bulb is located underneath the main beam bulb. Remove the rub-ber plug.
2. Pull on the bulb-holder to re-move it.
3. Replace the bulb H21.
4. Reposition the bulb-holder in the bracket and push it in.
5. Put back the rubber plug.
C H A N G I N G B U L B SH A L O G E N H E A D L A M P S