light Citroen C4 PICASSO 2008.5 1.G User Guide

Page 25 of 330

28
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to be
able to start the engine on a vehicle
with the (6-speed) Electronic Gearbox
System, or to quit position P in the
case of an automatic gearbox.
This warning lamp comes on if
you attempt to release the electric
parking brake without pressing the
brake pedal.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes
to indicate overheating of the clutch
if you excessively use the accelera-
tor to hold the vehicle on an uphill
slope. Use the brake pedal or the
electric parking brake.
Parking space available
This warning lamp comes
on when the parking space
function is selected.
It fl ashes while the space is
being measured. Electric child lock
If lit, the child lock is activat-
ed. This warning light is dis-
played a few seconds after
the function is activated.
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation The ESP/ASR system is put
into service automatically
when the vehicle is started. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the NaviDrive multifunction screen. A specifi c button, located in the cen-
tre of the fascia, permits deactiva-
tion of the system. This is confi rmed
by continuous lighting of this warn-
ing light and of the indicator light on
the button.
From approximately 30 mph (50km/h),
the system is reactivated automatically.
When the engine is running or the
vehicle is moving, the lighting of one of
the following warning lights indicates
the occurrence of a fault requiring inter-
vention on the part of the driver.
Any fault resulting in the display-
ing of a warning light must be the
subject of further diagnostics by
reading the associated message
on the multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.

Page 26 of 330

28
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to be
able to start the engine on a vehicle
with the (6-speed) Electronic Gearbox
System, or to quit position P in the
case of an automatic gearbox.
This warning lamp comes on if
you attempt to release the electric
parking brake without pressing the
brake pedal.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes
to indicate overheating of the clutch
if you excessively use the accelera-
tor to hold the vehicle on an uphill
slope. Use the brake pedal or the
electric parking brake.
Parking space available
This warning lamp comes
on when the parking space
function is selected.
It fl ashes while the space is
being measured. Electric child lock
If lit, the child lock is activat-
ed. This warning light is dis-
played a few seconds after
the function is activated.
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation The ESP/ASR system is put
into service automatically
when the vehicle is started. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the NaviDrive multifunction screen. A specifi c button, located in the cen-
tre of the fascia, permits deactiva-
tion of the system. This is confi rmed
by continuous lighting of this warn-
ing light and of the indicator light on
the button.
From approximately 30 mph (50km/h),
the system is reactivated automatically.
When the engine is running or the
vehicle is moving, the lighting of one of
the following warning lights indicates
the occurrence of a fault requiring inter-
vention on the part of the driver.
Any fault resulting in the display-
ing of a warning light must be the
subject of further diagnostics by
reading the associated message
on the multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.

Page 27 of 330

28
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The fl ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to be
able to start the engine on a vehicle
with the (6-speed) Electronic Gearbox
System, or to quit position P in the
case of an automatic gearbox.
This warning lamp comes on if
you attempt to release the electric
parking brake without pressing the
brake pedal.
In the case of the Electronic Gearbox
System, this warning lamp fl ashes
to indicate overheating of the clutch
if you excessively use the accelera-
tor to hold the vehicle on an uphill
slope. Use the brake pedal or the
electric parking brake.
Parking space available
This warning lamp comes
on when the parking space
function is selected.
It fl ashes while the space is
being measured. Electric child lock
If lit, the child lock is activat-
ed. This warning light is dis-
played a few seconds after
the function is activated.
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation
Dynamic stability control
(ESP/ASR) deactivation The ESP/ASR system is put
into service automatically
when the vehicle is started. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the NaviDrive multifunction screen. A specifi c button, located in the cen-
tre of the fascia, permits deactiva-
tion of the system. This is confi rmed
by continuous lighting of this warn-
ing light and of the indicator light on
the button.
From approximately 30 mph (50km/h),
the system is reactivated automatically.
When the engine is running or the
vehicle is moving, the lighting of one of
the following warning lights indicates
the occurrence of a fault requiring inter-
vention on the part of the driver.
Any fault resulting in the display-
ing of a warning light must be the
subject of further diagnostics by
reading the associated message
on the multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.

Page 28 of 330

29
I
I N S T R U M E N T S a n d C O N T R O L S
Lighting is associated
with the displaying of
another warning light:
Service If this comes on, it indi-
cates the occurrence of
a problem in one of the
systems which does
not have a specifi c
warning light.
In order to identify it, consult the mes-
sage on the multifunction display.
The warning light only comes on
temporarily in the case of the follow-
ing minor faults:
- incorrect closing of the doors, boot, rear screen and bonnet,
- fl at remote control battery,
- incorrect tyre pressure,
- the end of saturation of the particle emission fi lter (Diesel).
In the case of major faults, the
warning light remains on until the
operating fault is rectifi ed, contact a
CITROËN dealer as soon as possible. Braking
If this comes on, it indicates
the occurrence of a fault in
one of the braking systems:
- signifi cant drop in the level in the circuit,
- electronic brake force distribu- tion (EBFD) faulty (simultaneous
lighting of the ABS warning light),
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.

Application/Release of the
automatic electronic parking
brake
If this warning lamp comes
on permanently, it is confi rm-
ing that the parking brake is
applied.
If it fl ashes, it is indicating an ap-
plication or release fault. Urgently
contact a CITROËN dealer (see sec-
tion "Driving - § Electronic parking
brake"). Automatic electronic parking
brake fault
This warning lamp comes
on if there is a malfunction
in the automatic electronic
parking brake.
Deactivation of the automatic
functions of the automatic
electronic parking brake
This comes on if the "auto-
matic application" and "au-
tomatic release" functions
when you switch off the
engine are deactivated or
faulty.
Dynamic stability control
(ESP/ASR) The ESP/ASR system is put
into service automatically
when the vehicle is started.
Unless the system has been deactivat-
ed, if this warning light and the indicator
light on the button come on continu-
ously, this indicates the occurrence of
a fault in the ESP/ASR system or in the
hill start assistance.
Engine autodiagnostics system
If this comes on, it indicates
the occurrence of a fault in
the engine management
system.
If it fl ashes, it indicates the occurrence
of a fault in the emission control sys-
tem.
Central alert
- punctured wheel,
- braking,
- coolant temperature,
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.
Anti-lock braking system (ABS) If this comes on, it indicates
the occurrence of a fault in
the anti-lock braking system.
However, this does not prevent op-
eration of the vehicle's assisted
braking.

Page 29 of 330

30
I
I N S T R U M E N T S a n d C O N T R O L S Air bags If this comes on, it indicates
the occurrence of a fault in
one of the air bag or seat
belt pretensioner systems.
Maximum coolant temperature
If this comes on, it indicates
that the temperature in the
cooling system is too high.
Stop the vehicle immediately
and as safely as possible.
Low fuel level When the tank is full, all the
bars are lit up.
If the fuel low warning lamp
comes on accompanied by
an audible signal and a message on
the multifunction screen, there are ap-
proximately 7 litres of fuel remaining
in the tank and 2 or 3 bars fl ash in
the instrument panel.
When the last bar goes out, there
are approximately 2 litres of fuel
remaining in the tank.
A control located on the panel to the
right of the steering wheel allows
you to open the fuel fl ap from inside
the vehicle.
Battery charge
If this comes on, it indicates
the occurrence of a fault in
the battery charging circuit
(dirty or loose terminals, slack
or cut alternator belt, ...). Door open
A door, the boot or the rear
screen is open:
-
if the speed is below 6 mph (10 km/h), this
warning light comes on continuously.
- if the speed is higher than 6 mph (10 km/h), this warning light comes on continuously,
accompanied by an audible signal.
Seat belt not fastened/
unfastened
This warning lamp informs
you if the driver’s or front
passenger’s seat belt is
not fastened (depending
on model), and if the front
passenger’s (depending on
model) or the second row
passengers’ seat belts are
unfastened. The lit up positions rep-
resent those whose seat belts are
not fastened/unfastened. Seat belts unfastened during the
journey:
- the point corresponding to the
seat position with seat belt un-
fastened lights up between 0 and
20 km/h. Above 20 km/h (approx.
12 mph), it fl ashes accompanied
by a sound signal for around
120 seconds. The sound signal
stops when the ignition is switched
off or if a door is opened.
Depending on model, the front pas-
senger seat may be fi tted with a
presence sensor; the correspond-
ing warning lamp will only come on
if the seat is occupied and the seat
belt not fastened.
Driver’s or front passenger’s seat belt
not fastened with presence sensor:
-
the warning lamp lights up between
0 and 20 km/h. Above 20 km/h
(approx.12mph), it fl ashes accom-
panied by a message on the multi-
function screen and a sound signal
for around 120 seconds
.
Rear passengers’ or front passen-
ger’s seat belt not fastened without
presence sensor:
-
when the ignition is switched on, the
points corresponding to the seat po-
sitions with seat belts not fastened
remain lit up for 30 seconds.

Page 33 of 330

33
I
I N S T R U M E N T S a n d C O N T R O L S
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver’s door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
until it is reset to zero by the driver.

 With the ignition on, press the
button until zeros appear. Lighting rheostat
System for manual adjustment of
the brightness of the instruments
and controls in relation to the exte-
rior brightness.
Activation
When the lights are on:

 press the button to change the
brightness of the instruments
and controls,

 when the lighting reaches the
minimum setting, release the
button, then press again toin-
crease it,
or

 when the lighting reaches the
maximum setting, release the
button, then press again to re-
duce it,

 when the lighting reaches the
level of brightness required, re-
lease the button.
Deactivation
When the lights are off, or in day
mode on vehicles fi tted with daytime
lights, pressing the button does not
have any effect.

Page 37 of 330

37
II
M U L T I F U N C T I O N D I S P L A Y S
Personalisation -
Configuration
This permits activation/deactivation
of the:
- operation of the rear wiper,
-
automatic guide-me-home lighting,
- Xenon dual-function directional headlamps,
- electronic parking brake auto- matic functions (application/
release),
- door selectivity,
- lighting of daytime-running lamps (depending on country),
and selection of the:
- brightness intensity, time, date and units,
- screen language. Activating/deactivating the
rear screen wipe when you
engage reverse gear

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for ve-
hicle parameters. Confi rm your
choice with a press on C .

 Using B , select "parking assist-
ance". Confi rm your choice with
a press on C .

 Then by pressing C , select/dese-
lect "triggering of rear screen
wipe in reverse gear" to activate/
deactivate this.

 Validate with "OK" on the
screen.
Activating/deactivating the
automatic guide-me-home
lighting

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for ve-
hicle parameters. Confi rm your
choice with a press on C .
 Using B , select "lighting and
signalling". Confi rm your choice
with a press on C .

 Then by pressing C , select/dese-
lect "guide-me-home lighting"
to activate/deactivate this. After
activation, choose its duration:
press on C , then use B to select
the duration and then press on

C .

 Validate with "OK" on the
screen.
Activating/deactivating
the Xenon dual-function
directional headlamps

 Press on A .

 Use B to select "Personalisation-
Confi guration", then confi rm your
choice with a press on C .

 Then select the sub-menu for
vehicle parameters. Confi rm
your choice with a press on C .

 Using B , select "driving assist-
ance". Confi rm your choice with
a press on C .

 Then by pressing C , select/dese-
lect "directional headlamps" to
activate/deactivate them.

 Validate with "OK" on the
screen.

Page 46 of 330

46
III
C O M F O R T
Air conditioning
To ensure that your system operates
correctly, it is recommended to have
it checked regularly.
Water arising from condensation
in the air conditioning drains away
through a hole provided for this pur-
pose. A pool of water may thus form
under the vehicle when stationary.
To keep the air conditioning com-
pressor well sealed, it is essential to
operate the air conditioning at least
once in every month.
Regardless of the season, the air
conditioning is useful, since it re-
moves humidity and condensation.
To be effective, the air conditioning
should only be used with the win-
dows closed.
If after a lengthy stop in bright sunlight
the interior temperature is excessive,
air the passenger compartment by
opening the windows for a few mo-
ments, then close them again.
The air conditioning operates by using
power from the engine. This results in
a slight increase in fuel consumption.

Dust filter/Odour filter
(active carbon)
There is a fi lter for excluding odours
and dust.
This fi lter has to be changed in ac-
cordance with the vehicle mainte-
nance schedule (see "Maintenance
Guide").
Air circulation
Air vents on the fl oor underneath the
front seats provide enhanced heat-
ing for the rear seat positions; take
care not to obstruct them.
Air vents
The air vents to the face have grilles
and thumbwheels to adjust the air
fl ow and direction (up-down, right-
left).
The automatic regulation of the air
conditioning, inside the cabin, uses
a number of sensors (sunlight sen-
sor, outside temperature sensor...)
that relieve you of the need to make
frequent adjustments outside the
displayed temperature.
Be careful not to obstruct the sun-
light sensor, located on the dash-
board behind the instrument panel.
Sensors

Page 47 of 330

47
III
C O M F O R T
MANUAL AIR CONDITIONING
A. DRIVER’S CONTROL PANEL
1. Adjustment of the air blower speed
The air blower adjustment only op-
erates when the engine is running.
To adjust the air fl ow, press on but-
ton 1 :
to increase the fl ow of air,
to decrease the fl ow of air.
The level of air fl ow is shown by the pro-
gressive lighting of the warning lamps
depicting the ventilator blades 1 .
By reducing the fl ow to minimum,
you deactivate the air conditioning
system (OFF).
To achieve an agreeable level of com-
fort in the passenger compartment,
you should not leave this control too
long in the OFF position.
2. Adjustment of the air
distribution

 Press on button 2 to make the
display scroll through the differ-
ent types of air distribution.
The air distribution chosen
is shown by the lighting of
the corresponding warning
lamps on the display 2.
3. Mode of adjustment of temperature for
the passenger

 Press on button 3 to have inde-
pendent passenger control of
cabin air temperature. The warn-
ing lamp goes out.
While the passenger is adjusting
temperature,the warning lamp lights
up. 4. Air recirculation
This control is for isolating disagree-
able odours or fumes coming from
outside.

 Press on button 4 , to exclude
entry of outside air. The warning
lamp lights up.
This should be cancelled as soon as possible to permit renewal of
cabin air and to prevent misting.

 Press again on button 4 , to de-
activate air recirculation.
5. Air conditioning
The air conditioning can only oper-
ate when the engine is running. The
air blower control (adjusting the fl ow
of air) has to be activated in order for
air conditioning to be obtained.

 Press on button 5 . The warning
lamp lights up.
To be effective, the air condi-
tioning should be operated only-
with the windows closed.
If your vehicle is not equipped with
air conditioning, you will have the
same control panel but without the

A/C button.

Page 48 of 330

48
III
C O M F O R T
6. Deicing/Demisting of the rear screen
This operates only if the engine is
running.

 Press on button 6 to activate/
deactivate the electric deicing/
demisting of the rear screen and
the exterior rear view mirrors.
The warning lamp lights up.
7. Rapid Deicing/Demisting of front and rear windows
and rear view mirrors

 Press on button 7 . The warning
lamp lights up.
This function simultaneously activates:
- front deicing/demisting,
- optimum fl ow of air,
- recirculation prohibition,
- deicing/demisting of rear view mirrors and heated rear screen,
- air conditioning, if necessary.
To stop the function, press again on
button 7 . 8. Adjustment of the air
blower temperature
This control is for adjusting the tem-
perature of the air in the passenger
compartment. It can be used in cold
weather as well as in hot weather,
provided the air conditioning is
active.
The adjustment of the temperature
is continuous and progressive starting
from one side.
B. PASSENGER’S CONTROL PANEL
Adjustment of temperature

 Press on button 9 to take over
control of the temperature. The
warning lamp lights up.

 Rotate button 10 to adjust your
temperature.
The adjustment of the temperature
is continuous and progressive starting
from one side.
The deicing/demisting switch-
es off automatically to prevent
excessive consumption of
power.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 110 next >