boot Citroen C4 PICASSO 2009.5 1.G Owner's Guide

Page 190 of 338

156
IX
D R I V I N G
Loading/unloading
assistance

Grand C4
Picasso
C4 Picasso
The pneumatic suspension has an
additional function associated with
it: the possibility to raise or lower
the height of the rear of the vehicle
when stationary, in order to facilitate
loading/unloading of the boot. Increasing the height of the boot
fl oor

 Press continuously at the top of
the control A , which is located in
the boot, on the left-hand side.
This action will be accompanied by
an audible signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.

Returning to the
normal
height

 Press briefl y twice at the bottom
of the control A .
Decreasing the height of the boot
fl oor

 Press continuously at the bottom
of the control A .
This action will be accompanied by
a sound signal. You can stop the
movement at any time by releasing
the control.
3 beeps will confi rm that the move-
ment has gone as far as it can.
Returning to the
normal
height

 Press briefl y twice at the top of
the control A .
Driving with the boot in a
low position may damage
the components located un-
der the bodyshell.

Special features
- If you start the vehicle without having returned it to the normal
height, automatic correction will
activate as soon as the vehicle
starts to move. During the cor-
rection, the service warning lamp
lights up and a message on the
screen reminds you not to ex-
ceed 10 km/h (6 mph).
- The loading assistance does not function in the following instances:
- If the button B is lit up,
- in power economy mode,
- when you fi rst use the function, press for two seconds on the
control A to initialise the system.
All subsequent actions will be
followed immediately by the de-
sired results.

Page 200 of 338

167
XI
P R A C T I C A L I N F O R M A T I O N
PUNCTURE REPAIR KIT Using the kit
The kit is located in the boot under
the fl oor or under the fl ap in the sec-
ond row left-hand passenger foot-
well (open by turning the screw a
quarter of a turn).
 Tick the wheel to be repaired
on the speed limitation sticker
enclosed then affi x the sticker
to the vehicle's steering wheel
to remind you that a wheel is in
temporary use.

 Switch off the ignition.

 Clip the bottle 1 on the compres-
sor 2 .

 Check that the switch A is tilted
to position "0" .

 Connect the pipe of the bottle 1
to the valve of the tyre to be re-
paired.

 Unwind the pipe of the compres-
sor 2 fully before connecting it to
the bottle.

 Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket.

 Start the vehicle and leave the
engine running.
Complete system consisting of a
compressor and a bottle of sealant
which permits
temporary repair of
the tyre so that you can drive to the
nearest garage.
This repair kit is available from
CITROËN dealers.
It is designed to repair holes of
a maximum diameter of 4 mm,
located exclusively on the tyre
tread or shoulder. Avoid remov-
ing any foreign bodies which have
pene trated the tyre.

Page 213 of 338

179
XI
P R A C T I C A L I N F O R M A T I O N
Rear lamps
(Grand C4 Picasso)

1. Direction indicators
(PY21 W)

2. Stoplamps
(P21 W)

3. Reversing lamp
(P21 W)

4. Sidelamps (diodes)
For this type of lamp, contact a CITROËN dealer. Changing bulbs

 Identify the faulty bulb.

 With the tailgate open, undo the
3 screws located on the side of
the lens unit and pull it rearwards
to detach.

 Disconnect the connector linking
the lens unit to the boot. Do not
disconnect the diodes.

 Remove the seal.

 Remove the bulb-holder.

 Replace the bulbs.
To remove a bulb, rotate it a quarter turn.
To fi t the bulb, rotate it a quarter turn in the other direction.

 Reposition the bulb-holder.

 Refi t the seal.

 Reconnect the connector to the
lens unit.

 Arrange the harness in the open-
ing provided in the body.

 Refi t the lens unit to the body
and fi t and tighten the 3 screws. Number plate lamps (W 5 W)

 Insert a thin screwdriver into one
of the external holes of the lens.

 Push it outwards to unclip it.

 Remove the lens.

 Change the faulty bulb.

Page 214 of 338

180
XI
P R A C T I C A L I N F O R M A T I O N
Third brake lamp with bulb
(W 5 W)

 With the boot open, detach the
interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach
the 3 retaining lugs.

 Remove the lamp via the exte-
rior of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).
To refi t, carry out these operations in
reverse order.
Third brake lamp (diodes)
For the replacement of this type of
diode lamp, contact a CITROËN
dealer. Interior lighting
Interior lamp (1/W 5 W)
Detach the cover of the interior
lamp
1 with a thin screwdriver, close
to the button, to access the faulty
bulb.
Map reading lamps (2/W 5 W)
Detach the cover of the interior lamp.
To access the faulty bulb, detach the
partition for the reading lamp 2 con-
cerned, as necessary. Boot lamps (W 5 W)
Detach the unit by pushing it rear-
wards.
Torch (Krypton 3.6 V)

 Open the tab.

 Push with a fl at screwdriver
in the hole under the tab and
recover the bulb unit.

 Open the bulb unit fully to change
the bulb.

Page 215 of 338

180
XI
P R A C T I C A L I N F O R M A T I O N
Third brake lamp with bulb
(W 5 W)

 With the boot open, detach the
interior trim.

 Undo the nuts.

 Using a thin screwdriver, detach
the 3 retaining lugs.

 Remove the lamp via the exte-
rior of the tailgate.

 Remove the bulb-holder.

 Change the faulty bulb(s).
To refi t, carry out these operations in
reverse order.
Third brake lamp (diodes)
For the replacement of this type of
diode lamp, contact a CITROËN
dealer. Interior lighting
Interior lamp (1/W 5 W)
Detach the cover of the interior
lamp
1 with a thin screwdriver, close
to the button, to access the faulty
bulb.
Map reading lamps (2/W 5 W)
Detach the cover of the interior lamp.
To access the faulty bulb, detach the
partition for the reading lamp 2 con-
cerned, as necessary. Boot lamps (W 5 W)
Detach the unit by pushing it rear-
wards.
Torch (Krypton 3.6 V)

 Open the tab.

 Push with a fl at screwdriver
in the hole under the tab and
recover the bulb unit.

 Open the bulb unit fully to change
the bulb.

Page:   < prev 1-10 11-20 21-30 31-40