engine Citroen C4 PICASSO 2010.5 1.G Owner's Manual

27
F A M I L I A R I S A T I O N
D R I V I N G
Stop & Start
Engine going into STOP mode The "ECO" warning lamp comes
on in the instrument panel and
the engine goes into stand-by:
- with the 6-speed electronic gear-
box system ; at speeds below
4 mph (6 km/h), press the brake
pedal or put the selector lever into
neutral (position N) .
In certain circumstances the STOP
mode may not be available; the "ECO"
warning lamp fl ashes for a few seconds,
then goes off.

 150 The
"ECO" warning lamp goes
off and the engine restarts:
- with the selector lever in position A
or M , release the brake pedal,
- or with the selector lever in position
N and the brake pedal released,
change to position A or M ,
- or select reverse gear.
In certain circumstances, START mode
may be invoked automatically; the

"ECO" warning lamp fl ashes for a few
seconds, then goes off.

 151 Deactivation/Reactivation
You can deactivate the system at any
time by pressing the
"ECO OFF" button;
the button’s warning lamp comes on.
The system is reactivated automati-
cally every time you start the engine
with the key. Before refuelling or doing an-
ything under the bonnet, you
must switch off the ignition
with the key.

 151
Going into engine START mode

I
33
M O N I T O R I N G

Warning lamp is on Cause Action/Observations

Front
foglamps fi xed. The front foglamps are
switched on. Turn the ring on the stalk rearwards twice
to switch off the front foglamps.

Rear
foglamps fi xed. The rear foglamps are
switched on. Turn the ring on the stalk rearwards to
switch off the rear foglamps.

Diesel engine
pre-heating fi xed. The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp has switched off befor
e starting.
The duration for which the warning lamp is on is d etermined
by the climatic conditions.

Parking brake fi xed.
The parking brake is applied
or not properly released. Release the parking brake to switch off the
warning lamp, keeping your foot on the
brake pedal.
Observe the safety recommendations.
For further information on the parking
brake, refer to the "Driving" section.
fl ashing.
The parking brake is not fully
applied or is released.

Parking
space
sensors fi xed.
The parking space sensors
function is active. Press the corresponding button to
deactivate it.
fl ashing. The system is measuring the
space. Once the measurement has been done,
the warning lamp comes on fi xed again.

Electric child
lock temporarily. The electric child lock is
activated. Displayed for a few seconds after activating
the function and every time the ignition is
switched on.
For more information, refer to the "Child
safety" section.

I
38M O N I T O R I N G


Deactivation
of the automatic functions of the electric
parking brake
fi xed. The "automatic application"
(on switching off the engine)
and "automatic release"
functions are deactivated or
faulty. Activate the function (according to country)
via the vehicle confi guration menu or
contact a CITROËN dealer.

Warning lamp is on Cause Action/Observations


Dynamic
stability control
(ESP/ASR) fl ashing.
The ESP/ASR regulation is
active. The system optimises traction and
improves the directional stability of the
vehicle.
fi xed. Unless it has been
deactivated with the indicator
lamp on the button on, the
ESP/ASR system is faulty. Have it checked by a CITROËN dealer.

Engine
autodiagnosis system fi xed.
The emission control system
has a fault.
This lamp should switch off when the engine is sta
rted.
If it does not switch off, contact a CITROËN deale r
urgently.
fl ashing. The engine management
system has a fault. Risk of destruction of the catalytic convertor.
Have it checked by a CITROËN dealer.

Airbags temporarily.
This lamp comes on for a few
seconds when you turn on the
ignition, then switches off.
This lamp should switch off when the engine is
started.
If it does not switch off, contact a CITROËN deale
r.
fi xed. One of the airbag or seat belt
pretensioner systems has a
fault. Have it checked by a CITROËN dealer.

I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL --" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

III
60
C O M F O R T
3. Adjustment of air fan speed/Activation of the
"REST" function
to increase the air fl ow,
to decrease the air fl ow (this
button also has the "REST"
function).
The level of air fl ow is indicated on the
display by the progressive fi lling of the
fan blades.
If you place the air fan on position 0 ,
the system is deactivated. The air fan
display will be empty, with the indication
OFF.
To allow a degree of comfort
in the passenger compart-
ment while the engine is off,
you can operate the ven-
tilation for a few minutes using the
"REST" function.
When you leave the vehicle, any
passengers present can still have
the benefi t of air circulation, even
though the engine is not running.
This function is available when
you switch on the ignition as well
as when you stop the engine.
The air conditioning control screens
come on and the symbol represent-
ing the air fan is displayed while the
function is available. This button does not activate the air
conditioning, only the air fans. While
the REST function is active, the air
fl ow and distribution cannot be mod-
ifi ed.
On switching on the ignition:
- A press on the REST button ac- tivates the function for a period
of a few minutes. Two blades of
the fan will fi ll to indicate that the
function is active.
- The function can be deactivated and reactivated during the timed
period.
- At the end of the timed period, the screen will go off. 4. Adjustment of air
distribution

 Press button 4 to scroll
through the air distri-
bution settings on the
screen.
The air distribution you have chosen
is confi rmed by the corresponding
indicators in the screen.
There are 7 possible adjustments.
Adjustment of air fl ow
To adjust the fl ow of air, press the
button:
"REST" function: activation of
ventilation, engine off
On switching off the engine:
- The function can be activated
during a period of 30 seconds.
- A press on the REST button ac- tivates the function for period of
several minutes. The duration
and availability of the function
depends on the state of charge
of the battery. Locking the vehi-
cle has no effect on the function.
- A further press before the end of the period of operation stops the
function defi nitively.

III
68
C O M F O R T
Storing driving positions
System which memorises the elec-
trical settings of the driver’s seat and
door mirrors. It enables you to store
up to two positions using the buttons
on the side of the driver’s seat. Storing a position
Using buttons M/1/2

 Switch on the ignition.

 Adjust your seat and the door
mirrors.

 Press button M , then press but-
ton 1 or 2 within four seconds.
An audible signal is heard indi- cating that the position has been
stored.
Storing a new position cancels the
previous position. Recalling a stored position
Ignition on or engine running

 Briefl y press button 1 or 2 to re-
call the corresponding position.
An audible signal is heard indicating
the end of the adjustment.
When the ignition is on, after a few
consecutive position recalls, the
function will be deactivated until the
engine is started, to prevent dis-
charging of the battery.
Vehicle moving

 Press and hold button 1 or 2 until
the audible signal is heard indi-
cating the end of the adjustment.
Do not try to store a driving position
while driving.

IV
79
A C C E S S
Deadlocking using the key

 Turn the key to the right in the driv-
er's door lock to lock the vehicle
completely and hold it in this posi-
tion for more than two seconds to
close the windows automatically
in addition to locking.

 Turn the key to the right again
within fi ve seconds to deadlock
the vehicle.
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual cen-
tral control button.
Therefore, never leave anyone inside
the vehicle when it is deadlocked.
Deadlocking also triggers the timed
illumination of the exterior side spot
lamps and guide-me-home lighting,
if this is activated.

 First press this button to fold the
key.
Locating your vehicle
This function allows you to identify
your vehicle from a distance, especial-
ly when the light is poor. Your vehicle
must be locked.

 Press the closed padlock on the
remote control.
This will bring on the courtesy lamps
and exterior side spotlamps, as well
as fl ashing the direction indicators
for a few seconds. Guide-me-home lighting
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code
must be recognised in order for
starting to be possible.
This electronic engine immobiliser
locks the engine management sys-
tem a few minutes after the ignition
is switched off and prevents starting
of the engine by anyone who does
not have the key.
In the event of a mal-
function, you are in-
formed by lighting of
this warning lamp, an
audible signal and a
message on the multifunction screen.
In this case, your vehicle does not
start; contact a CITROËN dealer as
soon as possible.
Folding the key
A press on this button oper-
ates the guide-me-home light-
ing (lighting of the sidelamps,
dipped beam headlamps,
number plate lamps and exte-
rior side spotlamps (located underneath
the door mirrors)).
A second press before the end of the
timing cancels the guide-me-home
lighting.
Deadlocking is confi rmed by fi xed
lighting of the direction indicators for
approximately two seconds.
According to version, the door mir-
rors fold at the same time.

IV
80
A C C E S S
STARTING
1. "S": Steering lock
To unlock the steering, gently move
the steering wheel while turning the
key, without forcing it.
2. "M": Ignition on
Depending on the version of your
vehicle, the orange and red warn-
ing lamps should also come on for
a short time.
3. "D": Starter
Release the key as soon the engine
has started.
If the fi rst attempt fails, switch off the
ignition. Wait ten seconds then oper-
ate the starter again. Steering lock

1. "
S": After removing the key, turn
the steering wheel to lock the
steering. The key can only be re-
moved in position S .

2. "M": Ignition switched on, the
steering is unlocked (by turning
the key to position M , move
the steering wheel gently if
necessary).

3. "D": Starter position.
Key left in position "M"
audible warning
If you forget to remove the key from
the ignition, the ignition is switched
off automatically after one hour.
To switch the ignition back on, turn
the key to position S then back to
position M .

Do not run the engine in an en-
closed space or where there is
insuffi cient ventilation
.

You must always to keep the
engine running when moving in
order to retain braking and steer-
ing power assistance .

Never remove the ignition key
before the vehicle has come to a
complete stop.
STOPPING
Vehicles equipped with a
turbocharger
Never stop the engine without having
allowed it to run for a few seconds at
idle, this being the time required for
the turbocharger to return to a normal
speed.
Flicking the accelerator at the mo-
ment of switching off the ignition
could cause serious damage.
A heavy object (key fob...), attached
to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction.
Never turn the key to this position
when the engine is running.

IV
79
A C C E S S
Deadlocking using the key

 Turn the key to the right in the driv-
er's door lock to lock the vehicle
completely and hold it in this posi-
tion for more than two seconds to
close the windows automatically
in addition to locking.

 Turn the key to the right again
within fi ve seconds to deadlock
the vehicle.
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual cen-
tral control button.
Therefore, never leave anyone inside
the vehicle when it is deadlocked.
Deadlocking also triggers the timed
illumination of the exterior side spot
lamps and guide-me-home lighting,
if this is activated.

 First press this button to fold the
key.
Locating your vehicle
This function allows you to identify
your vehicle from a distance, especial-
ly when the light is poor. Your vehicle
must be locked.

 Press the closed padlock on the
remote control.
This will bring on the courtesy lamps
and exterior side spotlamps, as well
as fl ashing the direction indicators
for a few seconds. Guide-me-home lighting
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code
must be recognised in order for
starting to be possible.
This electronic engine immobiliser
locks the engine management sys-
tem a few minutes after the ignition
is switched off and prevents starting
of the engine by anyone who does
not have the key.
In the event of a mal-
function, you are in-
formed by lighting of
this warning lamp, an
audible signal and a
message on the multifunction screen.
In this case, your vehicle does not
start; contact a CITROËN dealer as
soon as possible.
Folding the key
A press on this button oper-
ates the guide-me-home light-
ing (lighting of the sidelamps,
dipped beam headlamps,
number plate lamps and exte-
rior side spotlamps (located underneath
the door mirrors)).
A second press before the end of the
timing cancels the guide-me-home
lighting.
Deadlocking is confi rmed by fi xed
lighting of the direction indicators for
approximately two seconds.
According to version, the door mir-
rors fold at the same time.