access to tools Citroen C4 PICASSO 2015 2.G Owner's Manual

257
Changing a wheel
The tools are installed in the boot under the fl o o r.
Remove
  the   boot   carpet   for   access   to   them.
Access to the tools
List of tools*
Procedure for changing a wheel with a punctured tyre for the spare wheel using the tools provided with the vehicle.
al

l of these tools are specific to your
vehicle
  and   can   vary   according   to   the   level  
o

f   equipment.   Do   not   use   them   for   other  
p

urposes.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   removing  
t

he   wheel   bolts.
2.
 C

hock   for   immobilising   the   vehicle   (except  
v

ersions   with   manual   gearbox).
3.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
4.
 W

heel   bolt   cover   removal   tool.
 F

or   removing   the   finishers   on   the   heads   of  
t

he   wheel   bolts   on   alloy   wheels.
5.
 S

ocket   for   the   security   bolts   (located   in   the  
g

love   box).
 F

or   adapting   the   wheelbrace   to   the   special  
"s

ecurity"
 b
olts.
*
  According   to   equipment.
7
Practical information

258
Taking out the wheel
F Unscrew  the   central   green   screw.
F  L ift   the   spare   wheel   towards   you   from   the  
r

e a r.
F
 
R
emove   the   wheel   from   the   boot.as t he spare wheel is narrower than the
wheels on the vehicle, in the event of a
puncture,
  the   punctured   wheel   must   be  
c

arried   in   the   boot.
The
  spare   wheel   is   located   in   the   boot   under  
t

he   floor.
For access to the spare wheel, refer to the
"Access   to   the   tools"   section.
Access to the spare wheel
Putting the spare wheel back in
place
F Return
  the   wheel   to   its   housing.
F U nscrew the central screw a few turns,
then
  put   it   in   place   in   the   middle   of   the  
w

heel.
F
 
F
ully  
t
ighten  
t
he  
c
entral  
s
crew  
t
o  
s
ecure  
t
he  
w

heel   correctly. F
 R eturn   the   box   to   its   position   in   the   middle  o
f   the   wheel.
Practical information

259
Changing a wheelProcedure for changing a wheel with a punctured tyre for the spare wheel using the tools provided with the vehicle.
S
ome
 
of
 
the
 
tools   are   accessible   from   inside  
t

he
 
boot.
The
 
wheel
 
chock   2 as well as the wheelbrace
extension
 6

 
are   stowed   under   the   right   hand  
b

oot
 
sill
 
trim.
The wheelbrace 1
  and   the   towing   eye   7 are
stowed
 
under
 
the   left   hand   boot   sill.
Access to the vehicle's tools*2. Wheel  chock   for   immobilising   the   vehicle  (
except   versions   with   manual   gearbox).
3.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
4.
 W

heel   bolt   head   cover   removal   tool.
 F

or   removing   the   wheel   bolt   head   finishers  
o

n   alloy   wheels.
5.
 S

ocket   for   the   security   bolts   (stowed   in   the  
g

love   box).
 F

or   adapting   the   wheelbrace   to   the   special  
s

ecurity   bolts.
6.
 W

heelbrace
 e
xtension.
 F

or   unscrewing/tightening   the   spare   wheel  
c

arrier   drive.
7.
 T

owing   eye.
Wheel with trim
When removing the wheel ,   detach   the   trim  f
irst   using   the   wheelbrace   1   pulling   at   the   valve  
p

assage   hole.
When refitting the wheel ,
  refit   the   trim  
s

tarting   by   placing   its   notch   facing   the   valve  
a

nd   press   around   its   edge   with   the   palm   of   your  
han

d.
List of tools*
all of these tools are specific to your vehicle
and  can   vary   according   to   equipment.   Do   not  
u

se   them   for   other   purposes.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   the   wheel  
f

ixing
 bol
ts. *
  
D
epending   on   version.   A   complete   set   of   tools  
i

s   provided   with   the   spare   wheel.
The
 
other
 
tools,
 
the
 
jack
 
3
 
and
 
the
 
tool
 
for
 r
emoving
 
the
 
wheel
 
bolt
 
head
 
finishers
 
for
 
alloy
 w
heels 4 ,
 
are
 
stowed
 
in
 
a
 
box
 
attached
 
to
 
the
 
spar

e
 w

heel.
The
 
assembly
 
is
 
secured
 
under
 
the
 
vehicle
 
in
 
a

 
carrier.
(See
 
the
 
"Access
 
to
 
the
 
spare
 
wheel"
 
section).
7
Practical information

260
Taking out the spare wheelThe spare wheel is supported by a carrier underneath t he v ehicle.
Access to the spare wheel*
F Take  out   the   wheel   /   tool   box   assembly  f
rom   the   rear   of   the   vehicle.
F
 
S
traighten   the   spare   wheel   for   access   to  
t

he   tools   (A ).
F
 
F

old
 
the
 
concertina
 
board
 
and
 
put
 
the
 
left
 
h

and
 
third
 
row
 
seat
 
into
 
position
 
(if
 
your
 
v

ehicle
 
has
 
them).
F
 
R

aise
 
the
 
pre-cut
 
section
 
of
 
carpet
 
to
 
e

xpose
 
the
 
nut
 
for
 
operating
 
the
 
spare
 
w

heel
 
carrier.
F
 
U

sing
 
the
 
extension
 
6
 
fitted
 
to
 
the
 
end
 
of
 
t

he wheelbrace 1 ,
 
turn
 
the
 
nut
 
clockwise
 
t

o
 
unwind
 
the
 
carrier
 
cable
 
until
 
the
 
spare
 
w

heel
 
reaches
 
the
 
ground.
 
Unwind
 
the
 
l

ength
 
needed
 
for
 
access
 
to
 
the
 
wheel.
Only
 
a
 
"space-saver"
 
type
 
of
 
spare
 
w

heel
 
can
 
be
 
fitted
 
under
 
the
 
vehicle.
*
 
Depending
 
on
 
version. F
 
D
etach   the   link   piece   from   the   tool   box  
l

id (B - C ).
F
 
P
ass   the   link   piece   through   the   middle   of  
t

he   wheel   to   free   it   (D ).
Practical information

261
A puncture wheel from the vehicle cannot   be   fitted   under   the   vehicle.   It  
m

ust  
b
e  
c
arried  
i
n  
t
he  
b
oot.  
U
se  
a
 
c
over  
t

o   protect   the   boot.
F
 
P

ress
 
the
 
tongue,
 
slide
 
the
 
tool
 
box
 
cover
 
t

o
 
the
 
centre
 
and
 
remove
 
it
 
for
 
access
 
to
 
t

he
 
other
 
tools
 
( jack
 
and
 
wheel
 
bolt
 
head
 
f

inisher
 
removal
 
tool
 
for
 
alloy
 
wheels).Putting the carrier and spare
wheel back in place
F Stow   the   corresponding   tools   in   the   box  a
nd   close   the   cover.
F
 
P
osition   the   tool   box   on   the   ground.
Stowing the tools
F Return  the   tools   to   the   box   and   stow   the  b
ox   in   the   vehicle's   boot.
F
 
W
ind   in   the   carrier   by   turning   the  
w

heelbrace   clockwise:   once   the   cable   is  
f

ully   wound   in   you   should   no   longer   feel  
an

y
 r
esistance.
F

S
tow the other tools in the locations
provided
  in   the   boot.
When
  the   spare   wheel   is   fitted   in   place  
o

f   a   punctured   wheel,   it   is   essential  
t

o   return   the   carrier   and   tools   to   their  
n

ormal   position   under   the   vehicle  
b

efore   moving   off.
7
Practical information

277
Before changing a fuse:
F  t he   cause   of   the   failure   must   be   identified  
a

nd
 r
ectified,
F
 
a
ll   electrical   consumers   must   b   switched  
o

f f,
F
 
t
he   vehicle   must   be   immobilised   with   the  
ig

nition
 o
ff,
F
 
i
dentify   the   failed   fuse   using   the   tables   and  
l

ayout   drawings   in   the   following   pages.
Changing a fuse
GoodFailed
The   replacement   of   a   fuse   not   shown   in  
t

he   tables   below   may   cause   a   serious  
m

alfunction   of   your   vehicle.   Contact  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop. Tw e e z e r
Changing a fuse
The extraction tweezer is located in the d
ashboard f usebox c ompartment.
For
  access   to   it:
F
 
o
pen   the   glove   box,
F
 
u
nclip   the   cover   by   pulling   at   the   top   left,  
t

hen   right,
F
 
d
isengage   the   cover   completely,   by  
c

arefully   pulling   in   the   direction   indicated  
b

y the arrow,
F
 
r
emove   the   tweezer.
Access to the tools
To replace a fuse, you must:
F  u se   the   special   tweezer   to   extract   the   fuse  
f

rom   its   housing   and   check   the   condition   of  
it

s
 f
ilament.
F
 
a
lways   replace   the   failed   fuse   with   a   fuse  
o

f   the   same   rating   (same   colour);   using   a  
d

ifferent   rating   could   cause   faults   (risk   of  
f

i r e).
If
  the   fuse   fails   again   soon   after   replacement,  
h

ave   the   vehicle's   electrical   system   checked   by  
a

  CITROËN   dealer   or   a   qualified   workshop.
7
Practical information

279
Type 1 fuse tables
Fusebox 1
Dashboard fuses
The fusebox is located in the lower dashboard (left-hand   side).
Access to the fuses
F Refer  to   the   paragraph   "Access   to   the   tools".Fuse N°
Rating Functions
F8 5 ASteering   mounted   controls
F18 20 ATouch   screen   tablet,   audio   and   navigation   system,   CD   player,  
U

SB   ports   and   auxiliary   sockets.
F16 15 AFront   12V   socket.
F15 15 ABoot   12V   socket.
F28 5 ASTART/STOP   button.
F30 15 ARear   wiper.
F27 15 AFront   screenwash   pump,   rear   screenwash   pump.
F26 15 AHorn.
F20 5 AAirbags.
F21 5 AInstrument   panel.
F19 5 ARain   and   sunshine   sensor.
F12 5 AKeyless   starting   unit.
F2 5 AManual
 h
eadlamp
 a
djustment
 c
ontrol.
7
Practical information

289
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it,
F
 
r
emove   the   towing   eye   from   its   housing.
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving   licence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another   vehicle   using   the   towing   eye.
Access to the tools
7
Practical information