CITROEN C4 PICASSO 2017 Repair Manual

59
Storing driving positions
Two positions can be stored and recalled, using
the buttons on the side of the driver's seat.
Storing a position using buttons
M /1/2
F Switch on the ignition.
F
Adj ust your seat.
F

P
ress button M , then press button 1
or
2
within four seconds.
An audible signal indicates that the position has
been stored.
Storing a
new position over writes the previous
position.
Recalling a stored position
F With the ignition on or the engine
running, press button 1 or 2 to recall the
corresponding position.
An audible signal indicates the completion of
the adjustment.
You can interrupt the current movement by
pressing button M , 1
or 2 or by using one of the
seat controls.
A stored position cannot be recalled while
driving.
Recalling stored positions is deactivated
45
seconds after switching off the ignition.
Additional adjustments
Head restraint height
F To raise a head restraint, pull it upwards.
F T o lower the head restraint, press the lug A
and push down on the head restraint at the
same time.
The head restraint has a
frame with notches
which prevents it from lowering; this is a
safety
device in case of impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
Removing a head restraint
F To remove the head restraint, press the lug A and pull the head restraint upwards.
F

T
o put the head restraint back in place,
engage the head restraint stems in the
openings, keeping them in line with the seat
backrest and press the lug A at the same
time.
Cushion height and angle
F Tilt the rear part of the control upwards or downwards to obtain the required height.
F

T
ilt the front part of the control upwards or
downwards to obtain the desired angle.
System which registers the electrical settings
of the driver's seat.
3
Ease of use and comfort

60
Relax head restraints
Depending on the version, you can fold the
sides for greater comfort.Never drive with the head restraints
removed; they must be fitted and correctly
adjusted.
Electric lumbar adjustment
F Press the control to obtain the desired lumbar support.
Massage function
Activation/Deactivation
F Press this button.
Its indicator lamp comes on and the
massage function is activated for
a
period of 1 hour.
During this time, massage is per formed in
6

cycles of 10 minutes (6 minutes of massage
followed by 4
minutes of break).
After one hour the function is deactivated, the
indicator lamp goes off.
Deactivate the massage function by pressing
this button, its indicator lamp goes off.
This function provides a
lumbar massage to the
occupants in front; it only operates when the
engine is running as well as in STOP mode of
the Stop & Start system.
Adjustment of intensity
Press this button to choose one of
the two available levels of massage
intensity.
Electric leg rest
Passenger seat with manual adjustments
F Press the front or rear part of the control to unfold or fold the leg rest.
The movement stops when your release the
control.
Electric passenger seat
Ease of use and comfort

61
Heated seats
F Use the adjustment wheel to switch on and select the level of heating required:
0: Of f.
1: Low.
2: Medium.
3: High.
With the engine running, the front seats can be
heated separately. Do not use the function when the seat
is not occupied.
Reduce the intensity of the heating as
soon as possible.
When the seat and passenger
compartment have reached an
adequate temperature, you can stop
the function; reducing the consumption
of electrical current reduces fuel
consumption.
Prolonged use at the highest setting is
not recommended for those with sensitive
skin.
There is a risk of burns for people whose
perception of heat is impaired (illness,
taking medication, for example).
There is a risk of overheating the system if
material with insulating properties is used,
such as cushions or seat covers.
Do not use the function:
-
i
f wearing damp clothing,
-
i
f child seats are fitted.
To avoid breaking the heating element in
the seat:
-
d
o not place heavy objects on the seat,
-
d
o not kneel or stand on the seat,
-
d
o not place sharp objects on the seat,
-
d
o not spill liquids onto the seat.
To avoid the risk of short-circuit:
-
d
o not use liquid products for cleaning
the seat,
-
n
ever use the heating function when
the seat is damp.
F
P
ush the control for wards or rear wards to
unfold or fold the leg rest.
The movement stops when your release the
control.
Prior to handling the leg rest, make sure
that nothing obstructs the movement.
3
Ease of use and comfort

62
Front armrest
Height adjustment
Second row seats
The 3 seats of the 2nd row are independent
and are the same width. Their backrests are
adjustable to adapt the boot load space. F

L

ower the armrest completely.
F

L

ift it again to the desired position (low,
intermediate or high).
F

O

nce it is in the high position, lift it to unlock
it and bring it to the low position.
Longitudinal adjustment
A. Longitudinal adjustment: lift the lever.
B. Tilt angle adjustment: pull the strap and
push the seat back.
C. Folding the seat: give a
firm upward pull
on the strap to unlock the seat.
D. Folding the seat from the back: pull the
strap then push the backrest for ward.
F

L
ift lever A , at the front of the seat cushion
and adjust the seat as required.
Ease of use and comfort

63
Rear head restraintsRelax head restraints
Never drive with the head restraints
removed; they must be fitted and correctly
adjusted.
Flat floor
Folding the seat
F Place the seats in the maximum rear wards longitudinal position.
The rear head restraints are removable and
have two positions:
-

h

igh, the position for use,
-

l

ow, the position for storage.
To raise the head restraint, pull it upwards.
To lower it, press the lug A then push the head
restraint downwards.
To remove it:
-

m

ove the head restraint to the high position,
-

p

ress the lug A while pulling the head
restraint upwards.
To replace it:
-

e

ngage the head restraint rods in the
apertures, keeping the head restraint in line
with the seat backrest. Depending on the version, you can fold the
sides to obtain a better comfortable position.
Each seat folds down to the floor to adapt the
boot volume as required.
" Comfort " position
F Pull strap B and push the seat back.
The backrest tilts and the cushion rotates
s l i g ht l y.
Returning the seat to its initial
position
F Pull strap B and push the seat forward.
Do not allow children to operate the
seats unsupervised.
3
Ease of use and comfort

64
From outside the vehicle
From the boot, for example when loading F
G
ive a firm upward pull on strap C , as
shown by the arrow, to unlock the seat;
keep pulling the strap until the seat is
completely folded. Push the backrest
slightly for ward so that the backrest tilts
and folds over the cushion. The seat and
cushion fold down to the floor.
Replacing the seat
F If necessary, straighten the continuity panels of the 2nd row of seats and lock
them.
F

R
aise the backrest and push it back until it
latches into place. Before per forming any operations on the
rear seats, to avoid damage to the seat
belts, make sure that the side belts are
properly tensioned. The central seat belt
must be put away. Secure the buckles
of the three seat belts to their anchoring
points.
Continuity panels
You can fold the second row seat(s) directly
from the boot, after having first folded the third
row seats.
F

P
ull strap D to unlock the desired seat and
give the backrest a
slight push for ward. To
prevent any damage to the mechanism,
strap D will unclip if excessive force is
applied. It is just a
matter of clipping it back
into place to make the system operational
again.
Each seat has a
continuity panel at the bottom
of the backrest, which, once unfolded:
-

a
llows for a continuous loading sur face in
the boot, whatever the position of the seats,
-

p
revents objects from sliding beneath the
2nd row seats.
These continuity panels are not designed
to support a
weight greater than 30 kg.
Ease of use and comfort

65
Getting out of the vehicle
from third row seatsReplacing the seat from
outside the vehicle, with
door open
If passengers are seated in the third row seats:
F

m
anually push the seat and cushion back as
far as it can go; the seat does not return to
the maximum back position, leaving space
free for the third row passengers' legs,
F

f
old the cushion until it locks.
Make sure there is nothing on or under the
cushion of the seat you want to move.
If this system fails (lever E ), the third row
passengers can also get out after having
folded the backrest of the second row
seats using strap D .
Do not let children operate the seats
unsupervised.
F
P
ull lever E . The seat unlocks and the
cushion comes up against the backrest.
F

Ke

ep lever E up by pushing it for wards. The
seat and cushion slide towards the front
seat.
This frees space behind the seat, allowing
the third row seat passengers to get into their
seats.
F

L

ift lever E . The seat unlocks and the
cushion moves up to the backrest.
F

P

ush the backrest holding lever E upwards.
Third row seats
Concertina boards
The two rigid concertina boards, which are built
in to the vehicle, cover the two third row seats,
when these are in the folded away position.
Before moving the seats, make sure that
the trays behind the front row seats are
properly stowed.
Unlocking/Locking the continuity panels
F

B

efore unfolding the continuity panels,
check that the 2nd row seats are moved
back as far as possible.
F

S

lide the latch of the continuity panel
upwards to unlock it.
F

S

traighten out the continuity panel, then
slide the latch downwards to lock it.
Access to third row seats
Third row seats are accessed via the second
row lateral seats.
3
Ease of use and comfort

66
Each of the two boards can support
a maximum load of 100 kg.
Folding the concertina
boards
Pull the strap, the 3 parts of the board fold into
c oncertina form.
When the third row seats are straightened,
these folded concertina boards can be left:
-
ei

ther flat behind the seats,
-

o
r in the vertical position,
thus clearing the inside of the seat as a
storage
space.
Installing the seats Seat storage
F Remove the load space cover.
For more information on the Interior
fittings and particularly on the load space
cover, refer to the corresponding section.
F

S
traighten the continuity panels of the
second row of seats and lock them in place.
F

F
old the concertina board and straighten it
vertically.
F

P
ull strap F , located behind the backrest
of the seat. The backrest tilts backwards
bringing the cushion. The seat locks in the
open position. F
S traighten the continuity panels of the
second row of seats and lock them in place.
F

L
ower the head restraints.
F

C
orrectly position the concertina board
vertically behind the seat.
F

M
ake sure that the seat belts of the 3
rd row
of seats are correctly fastened to the loops
and that they do not have any creases.
F

P

ull strap G , located at the bottom of the
backrest of the seat. The seat is unlocked.
F

T

hen, push the backrest slightly for wards.
The backrest tilts and folds on the cushion.
The folded seat is arranged at the back of
its storage area provided for this purpose.
F

P

ut the concertina boards back above the
folded down seats.
Ease of use and comfort

67
Configuration examples
4 seats
3 seats
Transporting items
7
seats 6
seats
Transporting items
5
seats
4
seats
Before working on the seats of the third
row, straighten the rigid boards of the
seats of the second row and lock them in
place.
Do not try to fold a

seat in the third row
without having opened it until the backrest
is fully locked.
Do not leave objects on the cushion or
below the cushion of the seats of the third
row, when you fold them.
Do not guide strap G when storing the
seat, your may jam your fingers.
Do not let children manipulate the seats
unsupervised.
Seat modular design and
configuration
Configuration examples
5 seats
3
Ease of use and comfort

68
In order to easily adapt your interior
space, you can fold all of the rear seats
individually and fold them onto the second
row floor, and beneath the floor on the
third row. This gives you a continuous load
floor up to the back of the front seats.
Folding or unfolding the seats must only
be done with the vehicle stationary.
Steering wheel adjustment
F When stationary , pull the control lever
to release the steering wheel adjustment
mechanism.
F

A
djust the height and reach to suit your driving
position.
F

P
ush the control lever to lock the steering wheel.
As a safety measure, these adjustments
s hould only be carried out with the vehicle
stationary.
Mirrors
Door mirrors
Each fitted with an adjustable mirror glass
permitting the lateral rearward vision necessary
for overtaking or parking.
They can also be folded for parking in narrow
spaces.
Demisting – Defrosting
Demisting-defrosting of the door
mirrors operates with the engine
running, by switching on the heated
rear screen.
For more information on Rear screen
demist - defrost , refer to the associated
section.
Adjustment
As a safety measure, the mirrors should
b e adjusted to reduce the blind spots.
Objects seen in the mirror are in reality
closer than they appear.
Take this into account when assessing
the distance of vehicles approaching from
behind.
F

M
ove control A to the right or to the left to
select the corresponding mirror.
F

M
ove control B in any of the four directions
to adjust.
F

R
eturn control A to the central position.
Folding
F From outside: lock the vehicle using the
electronic key or the " K eyless Entry and
Starting" system.
F

F
rom inside: with the ignition on, pull
the control A from the central position
rearwards.
Ease of use and comfort