lights Citroen C4 PICASSO DAG 2008.5 1.G Owner's Manual (330 Pages)

22
F A M I L I A R I S A T I O N
Seat belts not fastened/
unfastened warning lamp This warning lamp informs you
if the driver’s or front passen-
ger’s seat belt is not fastened
(depending on model), and if
the front passenger’s (depend-
ing on model) or the second-
row passengers’ seat belts are
unfastened. The lit up positions
represent those whose seat belts are
not fastened/unfastened.
You can use electrical central locking or
unlocking by pressing on button A .
If one of the doors is open or is not
closed properly, central locking will not
work. Tyre deflation detection
This function warns you if a tyre is deﬂ ated
or punctured.
This system does not absolve the driver
of the need to regularly check the tyre
pressures.
The service warning lamp
lights up, and a vehicle out-
line is displayed, accompa-
nied by a message and a
sound signal.
Deﬂ ation warning
The STOP warning lamp lights
up, and a vehicle outline is
displayed, accompanied by a
message and a sound signal.
Puncture

 30

 115
Anti-intrusion security
Once the function has been activated,
when starting the engine, the system
automatically locks the doors once you
reach approximately 10 km/h (approxi-
mately 6 mph).
This function can be deactivated by press-
ing button
A for more than two seconds.

 79
M O N I T O R I N G
Locking from inside
Instrument panel
with multifunction screen A

 24
with multifunction screen C
 25
with NaviDrive multifunction screen
 26

1. Instrument panel.

2. Multifunction screen.

3. Control buttons.

4. Warning lamps display zone.

27
I
I N S T R U M E N T S a n d C O N T R O L S
Indicator and warning lights
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle's ignition
is switched on.
When the engine is started, these
warning lights should switch off.
If they remain on, before moving off,
consult the warning light concerned. Associated warnings
The switching on of certain warning
lights may be accompanied by an
audible signal and a message on
the multifunction display.
The warning lights may come on
continuously or ﬂ ash.
Certain warning lights may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situa-
tion is normal or whether a fault has
occurred. Operation indicator lights
If one of the following indicator lights
comes on, this conﬁ rms that the cor-
responding system has come into
operation.
Front fog lamps.
Left-hand direction
indicator.
Side lights.
Main beam headlamps.
Dipped headlamps.
Right-hand direction
indicator.
Rear fog lamp.
Visual indicators informing the driver
that a system is in operation (opera-
tion or deactivation indicator lights) or
of the occurrence of a fault (warning
light).

28
I
I N S T R U M E N T S a n d C O N T R O L S
"Foot on brake" The ﬂ ashing of this warning
lamp on the display informs
you that you need to press
the brake pedal in order to
be able to start the engine on a ve-
hicle with the (6-speed) Electronic
Gearbox System, or to quit position P
in the case of an automatic gearbox.
This warning lamp comes on if you
attempt to release the electric parking
brake without pressing the brake
pedal.
In the case of the Electronic Gearbox
System, this warning lamp ﬂ ashes
to indicate overheating of the clutch
if you excessively use the accelera-
tor to hold the vehicle on an uphill
slope. Use the brake pedal or the
electric parking brake.
Parking space available
This warning lamp comes
on when the parking space
function is selected.
It ﬂ ashes while the space is
being measured. Electric child lock
If lit, the child lock is activated.
This warning light is dis-
played a few seconds after
the function is activated.
Deactivation warning lights
If one of the following warning lights
comes on, this conﬁ rms that the
corresponding system has been
switched off intentionally.
Dynamic stability control (ESP/
ASR) deactivation.
The ESP/ASR system is put
into service automatically
when the vehicle is started. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter. A speciﬁ c button, located in the cen-
tre of the fascia, permits deactiva-
tion of the system. This is conﬁ rmed
by continuous lighting of this warning
light and of the indicator light on the
button.

From approximately 30 mph (50 km/h),
the system is reactivated automati-
cally.
When the engine is running or the ve-
hicle is moving, the lighting of one of
the following warning lights indicates
the occurrence of a fault requiring in-
tervention on the part of the driver.
Any fault resulting in the display-
ing of a warning light must be the
subject of further diagnostics by
reading the associated message
on the multifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.
Passenger’s air bag system
deactivation
The passenger’s air bag sys-
tem is put into service auto-
matically when the vehicle is
started.A speciﬁ c control, lo-
cated in the glove box, permits deacti-
vation of the system. This is conﬁ rmed
by continuous lighting of this warning
light on the instrument panel or a mes-
sage on the NaviDrive multifunction
screen.

30
I
I N S T R U M E N T S a n d C O N T R O L S Air bags If this comes on, it indicates
the occurrence of a fault in
one of the air bag or seat
belt pretensioner systems.
Maximum coolant temperature
If this comes on, it indicates
that the temperature in the
cooling system is too high.
Stop the vehicle immediately
and as safely as possible.
Low fuel level When the tank is full, all the
bars are lit up.
If the fuel low warning lamp comes on
accompanied by an audible signal and
a message on the multifunction screen,
there are approximately 7 litres of fuel
remaining in the tank and 2 or 3 bars
ﬂ ash in the instrument panel.
When the last bar goes out, there
are approximately 2 litres of fuel re-
maining in the tank.
A control located on the panel to the
left of the steering wheel allows you
to open the fuel ﬂ ap from inside the
vehicle.
Battery charge If this comes on, it indicates
the occurrence of a fault in
the battery charging circuit
(dirty or loose terminals, slack
or cut alternator belt,...). Door open
A door, the boot or the rear
screen is open:
- if the speed is below 6 mph
(10 km/h),this warning light
comes on continuously.
- if the speed is higher than 6 mph (10 km/h), this warning
light comes on continuously, ac-
companied by an audible signal.
Seat belt not fastened/
unfastened This warning lamp informs
you if the driver’s or front
passenger’s seat belt is
not fastened (depending
on model), and if the front
passenger’s (depending on
model) or the second row
passengers’ seat belts are
unfastened. The lit up positions rep-
resent those whose seat belts are
not fastened/unfastened. Seat belts unfastened during the
journey:
- the point corresponding to the
seat position with seat belt un-
fastened lights up between 0 and
20 km/h. Above 20 km/h (approx.
12 mph), it ﬂ ashes accompanied
by a sound signal for around
120 seconds. The sound sig-
nal stops when the ignition
is switched off or if a door is
opened.
Depending on model, the front pas-
senger seat may be ﬁ tted with a
presence sensor; the correspond-
ing warning lamp will only come on
if the seat is occupied and the seat
belt not fastened.
Driver’s or front passenger’s seat belt
not fastened with presence sensor:
- the warning lamp lights up between
0 and 20 km/h. Above 20 km/h
(approx.12mph), it ﬂ ashes accom-
panied by a message on the multi-
function screen and a sound signal
for around 120 seconds.
Rear passengers’ or front passen-
ger’s seat belt not fastened without
presence sensor:
- when the ignition is switched on, the points corresponding to the seat po-
sitions with seat belts not fastened
remain lit up for 30 seconds.

33
I
I N S T R U M E N T S a n d C O N T R O L S
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver's door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
until it is reset to zero by the driver.

 With the ignition on, press the
button until zeros appear. Lighting rheostat
System for manual adjustment of
the brightness of the instruments
and controls in relation to the exterior
brightness.
Activation
When the lights are on:

 press the button to change the
brightness of the instruments
and controls,

 when the lighting reaches the
minimum setting, release the
button, then press again to in-
crease it,
or

 when the lighting reaches the
maximum setting, release the
button, then press again to re-
duce it,

 when the lighting reaches the
level of brightness required, re-
lease the button.
Deactivation
When the lights are off, or in day
mode on vehicles ﬁ tted with daytime
lights, pressing the button does not
have any effect.

47
III
C O M F O R T
MANUAL AIR CONDITIONING
A. DRIVER’S CONTROL PANEL
1. Adjustment of the air blower speed
The air blower adjustment only op-
erates when the engine is running.
To adjust the air ﬂ ow, press on button 1 :
to increase the ﬂ ow of air,
to decrease the ﬂ ow of air.
The level of air ﬂ ow is shown by the pro-gressive lighting of the warning lamps
depicting the ventilator blades 1 . By reducing the ﬂ ow to minimum,
you deactivate the air conditioning
system (OFF).
To achieve an agreeable level of
comfort in the passenger compart-
ment, you should not leave this con-
trol too long in the OFF position.
2. Adjustment of the air
distribution

 Press on button 2 to make the
display scroll through the different
types of air distribution.
The air distribution chosen
is shown by the lighting of
the corresponding warning
lamps on the display 2.
3. Mode of adjustment of temperature for the
passenger

 Press on button 3 to have inde-
pendent passenger control of
cabin air temperature. The warning
lamp goes out.
While the passenger is adjusting
temperature,the warning lamp lights up. 4. Air recirculation
This control is for isolating disagree-
able odours or fumes coming from
outside.

 Press on button 4 , to exclude
entry of outside air. The warning
lamp lights up.
This should be cancelled as soon as possible to permit renewal of
cabin air and to prevent misting.

 Press again on button 4 , to de-
activate air recirculation.
5. Air conditioning
The air conditioning can only oper-
ate when the engine is running. The
air blower control (adjusting the ﬂ ow
of air) has to be activated in order for
air conditioning to be obtained.

 Press on button 5 . The warning
lamp lights up.
To be effective, the air condi-
tioning should be operated only-
with the windows closed.
If your vehicle is not equipped with
air conditioning, you will have the
same control panel but without the

A/C button.

48
III
C O M F O R T
6. Deicing/Demisting of the rear screen
This operates only if the engine is
running.

 Press on button 6 to activate/de-
activate the electric deicing/de-
misting of the rear screen and
the exterior rear view mirrors.
The warning lamp lights up.
7. Rapid Deicing/Demisting of front and rear windows
and rear view mirrors

 Press on button 7 . The warning
lamp lights up.
This function simultaneously activates:
- front deicing/demisting,
- optimum ﬂ ow of air,
- recirculation prohibition,
- deicing/demisting of rear view mirrors and heated rear screen,
- air conditioning, if necessary.
To stop the function, press again on
button 7 . 8. Adjustment of the air
blower temperature
This control is for adjusting the tem-
perature of the air in the passenger
compartment. It can be used in cold
weather as well as in hot weather,
provided the air conditioning is active.
The adjustment of the temperature
is continuous and progressive start-
ing from one side.
B. PASSENGER’S CONTROL PANEL
Adjustment of temperature

 Press on button 9 to take over
control of the temperature. The
warning lamp lights up.

 Rotate button 10 to adjust your
temperature.
The adjustment of the temperature
is continuous and progressive starting
from one side.
The deicing/demisting
switches off automatically
to prevent excessive con-
sumption of power.

51
III
C O M F O R T

Closing of the air inlet

 Press on button 5 to close
off the entry of air from
outside.
Whilst retaining the other adjust-
ments, this position enables the
driver at any time to exclude any dis-
agreeable odours or fumes coming
from outside the vehicle. It should
be cancelled as soon as possible to
permit renewal of cabin air and to
prevent misting.

Entry of air (manual mode)

 Press on button 5 to activate en-
try of air from the outside. The
warning lamp goes out.

 Press once on button 5 to return
to the initial status (entry of air in
automatic mode).
The air recirculation can also be ac-
cessed by means of a press on the
control, located low down to one side
of the steering wheel (see "§ Fixed
centred controls steering wheel"). 6. Adjustment mode for the
rear passengers
This button decides whether
or not the rear passengers
may use their adjustment
controls.
There are three possible statuses
for this button:

Locking of the rear
passenger controls

Authorisation of
the rear passenger
controls

Closing of the air
ﬂ ow for the rear
passengers
The supply of air is cut off.
With additional air conditioning, in
cold weather you are advised to
close the supply of air to the rear
passengers (no hot air distribution
possible via these air vents).
The rear passengers can use their
adjustment controls at their conven-
ience.
The driver imposes his adjustment
on the rear passengers. In this case,
the rear passenger controls are de-
activated. 7. Panel display mode: black
panel function
This function turns the dis-
plays and panel backlighting
on or off.
- Function activated, a press on any button will light up the screen
temporarily.
- press on button 7 deactivates
the function, lighting f buttons
and screen is again permanent.
This function optimises notably the
visual comfort for driving at night.
8. Deicing/Demisting of the rear screen
This can only operate when the en-
gine is running.

 Press on button 8 to activate/de-
activate the electric deicing of
the rear screen and, according to
version, of the exterior rear view
mirrors. The warning lamp lights
up and the symbol appears on
the display.
It switches off automatically
to prevent excessive con-
sumption of power.

lights Citroen C4 PICASSO DAG 2008.5 1.G Owner's Manual

Page 19 of 330

Page 24 of 330

Page 25 of 330

Page 26 of 330

Page 27 of 330

Page 29 of 330

Page 33 of 330

Page 47 of 330

Page 48 of 330

Page 52 of 330

CITROEN Manuals