check engine Citroen C4 PICASSO DAG 2010.5 1.G Owner's Manual
Page 15 of 355
18
F A M I L I A R I S A T I O N
Seat belts not fastened/
unfastened warning lamp This warning lamp informs you if
the driver’s or front passenger’s
s e a t b e l t i s n o t f a s t e n e d ( d e -
p e n d i n g o n m o d e l ) , a n d i f t h e
f r o n t p a s s e n g e r ’ s ( d e p e n d i n g
o n m o d e l ) o r t h e s e c o n d - r o w
passengers’ seat belts are unfastened.
The illuminated positions represent
those whose seat belts are not fas-
tened/unfastened.
Once the function has been activated,
when starting the engine, the system
automatically locks the doors once you
r e a c h a p p r o x i m a t e l y 6 m p h ( 1 0 k m / h ) .
This function can be deactivated
by pressing button A for more than
two seconds.
Tyre under-inflation detection
This function warns you if a tyre is de-
fl a t e d o r p u n c t u r e d .
This system does not absolve the driver
of the need to regularly check the tyre
pressures.
The service warning lamp comes
on, and a vehicle outline is dis-
played, accompanied by a mes-
sage and an audible signal.
U n d e r - i n fl a t i o n w a r n i n g
The STOP warning lamp comes
on, and a vehicle outline is dis-
played, accompanied by a mes-
sage and an audible signal.
Puncture
40
124
88
M O N I T O R I N G
Automatic central locking
Instrument panel
with multifunction screen A or C
with the MyWay or NaviDrive
multifunction screen
1. Instrument panel.
2. Multifunction screen.
3. Control buttons.
4. Warning lamps display zone.
30
31 Manual central locking
You can use electrical central locking or
unlocking by pressing on button
A .
If one of the doors is open or is not
closed properly, central locking will not
work.
Page 22 of 355
25
F A M I L I A R I S A T I O N
163
Electric parking brake
Before leaving the vehicle, check that
the electric parking brake warning
lamp P ( r e d ) i s o n fi x e d ( n o t fl a s h i n g ) .
If you leave the vehicle with the en-
gine running, apply the parking brake
manually.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake. Parking space sensor
You can activate this function by press-
ing button
A .
Once the space has been measured, the
system displays the following messages:
< 1 2 m p h ( 2 0 k m / h )
Parking possible
P a r k i n g d i f fi c u l t
Parking not advised
This device combines:
- automatic functions: Automatic ap-
plication when the engine stops and
automatic release on use of the ac-
c e l e r a t o r ( a u t o m a t i c o p e r a t i o n b y
d e f a u l t ) ;
- manual use: Manual application/ release of parking brake is possible
by operating control lever A .
When in automatic mode, it remains
possible to apply or release the parking
brake at any time:
To apply it, pull on the lever A .
To release it, pull then release lever A .
Hill start assist
To aid starting on a gradient, your vehicle
i s e q u i p p e d w i t h a s y s t e m w h i c h k e e p s
it immobilised for about 2 seconds, the
approximate time it takes to move your
foot from the brake pedal to the accel-
erator pedal.
143
D R I V I N G
136
Do not drive if the parking brake
warning lamp and the P indicator on
the lever A are on.
Page 34 of 355
I
38M O N I T O R I N G
Deactivation
of the automatic
functions of the electric
parking brake fi x e d . The "automatic application"
(on switching off the engine)
and "automatic release"
functions are deactivated or
faulty. Activate the function (according to country)
v i a t h e v e h i c l e c o n fi g u r a t i o n m e n u o r
contact a CITROËN dealer.
Warning lamp is on Cause Action/Observations
Dynamic
stability control
(ESP/ASR) fl a s h i n g .
The ESP/ASR regulation is
active. The system optimises traction and improves
the directional stability of the vehicle.
fi x e d . Unless it has been deactivated
with the indicator lamp on
the button on, the ESP/ASR
system is faulty. Have it checked by a CITROËN dealer.
Engine
autodiagnosis system fi x e d .
The emission control system
has a fault.
This lamp should switch off when the engine is sta
rted.
If it does not switch off, contact a CITROËN deale r
urgently.
fl a s h i n g . The engine management
system has a fault. Risk of destruction of the catalytic convertor.
Have it checked by a CITROËN dealer.
Airbags temporarily.
This lamp comes on for a few
seconds when you turn on the
ignition, then switches off.
This lamp should switch off when the engine is
started.
If it does not switch off, contact a CITROËN deale
r.
fi x e d . One of the airbag or seat belt
pretensioner systems has a
fault. Have it checked by a CITROËN dealer.
Page 38 of 355
I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
c a t e t h e d i p s t i c k a n d t h e o i l fi l l e r c a p
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
l e v e l v i a t h e o i l fi l l e r
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count.
Page 39 of 355
I
42M O N I T O R I N G
Service indicator zero reset
Engine oil level indicator
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
T h i s i s i n d i c a t e d b y t h e fl a s h i n g o f
"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
c a t e t h e d i p s t i c k a n d t h e o i l fi l l e r c a p
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
l e v e l v i a t h e o i l fi l l e r
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count.
Page 54 of 355
III
56
C O M F O R T
Air conditioning
To ensure that your system operates
correctly, it is recommended that you
have it checked regularly.
Water arising from condensation
in the air conditioning drains away
through a hole provided for this pur-
pose. A pool of water may thus form
under the vehicle when stationary.
To preserve the sealing of the air
conditioning compressor, operate
the air conditioning at least once a
month.
Regardless of the season, the air
conditioning is useful, since it re-
moves humidity and condensation.
To be effective, the air conditioning
should only be used with the win-
dows closed.
If after a lengthy stop in bright sun-
light the interior temperature is
excessive, air the passenger com-
partment by opening the windows
for a few moments, then close them
again.
The air conditioning operates by
using power from the engine. This
results in a slight increase in fuel
consumption.
Dust filter/Odour filter (active
carbon)
T h e r e i s a fi l t e r f o r e x c l u d i n g o d o u r s
and dust.
T h i s fi l t e r h a s t o b e c h a n g e d i n
accordance with the vehicle's ser-
vicing schedule (see "Maintenance
and Warranty Guide").
Air circulation
A i r v e n t s o n t h e fl o o r u n d e r n e a t h t h e
front seats provide enhanced heat-
ing for the rear seat positions; take
care not to obstruct them.
Air vents
The air vents to the face have grilles
and thumbwheels to adjust the air
fl o w a n d d i r e c t i o n ( u p - d o w n , r i g h t -
left).
The automatic regulation of the air
conditioning in the passenger com-
partment uses a number of sensors
(sunshine sensor, ambient tempera-
ture sensor...) that relieve you of the
need to make frequent adjustments
to the displayed temperature.
Take care not to obstruct the sun-
shine sensor, located on the dash-
board behind the instrument panel.
Sensors
Page 162 of 355
IX
136
D R I V I N G
ELECTRIC PARKING BRAKE
The electric parking brake operates
as follows:
- Automatic application/release
Application is automatic when the engine stops, release is automatic
on use of the accelerator.
- Manual application/release
Manual application/release of the parking brake is possible
by pulling control lever A while
pressing the brake pedal. Manual application
With the vehicle stationary, to apply
the parking brake whether the engine
is running or not,
pull control lever A . Manual release
With the ignition on or the engine
running, to release the parking
brake, press on the brake pedal, or
the accelerator,
pull then release
control lever A .
-
the extinction of the warning
lamp P in control lever A and
in the instrument panel,
- the display of a message "Handbrake off" in the multifunc-
tion screen.
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warn-ing lamp P in control
lever A and in the instru-
ment panel,
- the display of a message "Handbrake on" in the multifunc-
tion screen.
When the driver’s door is
opened with the engine running,
a beep is heard and a message
displayed if the parking brake has not
been applied.
Before getting out of the vehicle, check
that the warning lamp P i s o n fi x e d i n t h e
i n s t r u m e n t p a n e l ( n o t fl a s h i n g ) .
The full application of the parking
b r a k e i s c o n fi r m e d b y :
If you pull control lever A
without pressing the brake
pedal, the parking brake
will not be released and
the "Foot on brake" warn-
ing lamp will come on in
the instrument panel.
Page 163 of 355
IX
137
D R I V I N G
Automatic application,
engine off
With the vehicle stationary, the park-
ing brake is automatically applied
when the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y : -
the lighting of warning lamp
P in control lever A and in
the instrument panel,
Automatic release
The electric parking brake releases
automatically and progressively
when you press the accelerator:
Manual gearbox ( fi r s t g e a r o r
reverse gear engaged) : press
down fully on the clutch pedal
then press on the accelerator
pedal and move off.
Automatic gearbox : accelerate
with the selector in position D , M
or R .
Electronic gearbox : accelerate
with the selector in position A , M
or R .
Full release of the parking brake is
c o n fi r m e d b y : - the extinction of warning lamp P in control lever A
and in the instrument
panel,
- the display of a message "Handbrake off" in the multifunc-
tion screen.
When stationary, with the engine
running, do not press the acceler-
ator pedal unnecessarily, as you
may release the parking brake.
Maximum application
If necessary, you can use maximum
application of the parking brake. It
is obtained by means of a long pull
on control lever A , until you see the
message "Handbrake on" and an
audible signal is heard.
Maximum application is essential:
- when towing a caravan or a trail- er, if the automatic functions are
activated but you are applying
the parking brake manually,
- when the gradient you are parked on is variable in its effect (e.g. on
a f e r r y , i n a l o r r y , d u r i n g t o w i n g ) ,
- when towing, when loaded or when parking on a gradient, turn
the front wheels towards the
pavement and engage a gear
when you park,
- after a maximum application, the release time will be longer.
Before leaving the vehicle,
check that warning lamp P
in the instrument panel is
o n fi x e d , n o t fl a s h i n g .
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message
"Handbrake on" in the multifunc-
tion screen.
The normal operating sound will con-
fi r m t o y o u t h e a p p l i c a t i o n / r e l e a s e o f
the electric parking brake.
Page 164 of 355
IX
138
D R I V I N G
To immobilise the vehicle,
engine running
To immobilise the vehicle when sta-
tionary with the engine running, you
must apply the parking brake manu-
ally by pulling on control lever A .
The application of the parking brake
i s c o n fi r m e d b y : - the lighting of warning lamp P in control A and
in the instrument panel,
- the display of a message "Handbrake on" in the multifunc-
tion screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
in the instrument panel is
o n fi x e d ( n o t fl a s h i n g ) . Particular situations
In certain situations (e.g. starting
t h e e n g i n e ) , t h e p a r k i n g b r a k e c a n
automatically alter its force. This is
normal operation.
To move your vehicle without start-
i n g t h e e n g i n e ( t o w i n g , e t c . . . ) , b u t
with the
ignition on , press the brake
pedal and release the parking brake
by pulling then releasing control
lever A .
The full release of the parking
b r a k e i s c o n fi r m e d b y t h e e x t i n c -
tion of warning lamp P ( r e d ) i n t h e
instrument panel and the display of
a message "Handbrake off" in the
multifunction screen.
If the parking brake malfunctions
while applied or if the battery runs
fl a t , a n e m e r g e n c y r e l e a s e r e m a i n s
possible.
Activation/Deactivation of the
automatic functions *
The automatic application when
the engine is switched off and the
automatic release when you press
the accelerator can be deactivated.
Activation/deactivation is performed
u s i n g t h e c o n fi g u r a t i o n m e n u o f t h e
multifunction screen. To do so, se-
lect "Vehicle parameters/Comfort/
Automatic handbrake."
The deactivation of these
f u n c t i o n s i s c o n fi r m e d b y t h e
lighting of this warning lamp
on the instrument panel.
* According to country
The deactivation of these func-
t i o n s i s c o n fi r m e d b y t h e l i g h t i n g o f
this warning lamp in the instrument
panel. With the automatic functions
deactivated, the application and re-
lease of the parking brake are done
manually.
Page 168 of 355
IX
142
D R I V I N G
SITUATION
CONSEQUENCES
4 Display of message "
Parking brake faulty "
and the following warning lamps:
and/or fl a s h i n g - The automatic functions are deactivated.
- Hill start assist is not available.
To apply the electric parking brake:
Immobilise the vehicle and switch off the ignition
Pull the control lever for at least 5 seconds or until maximum
application.
Switch on the ignition and check that the electric parking brake
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp P fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:
Switch on the ignition.
Pull the control lever and hold it for approximately 3 second s.
5 Display of message "
Parking brake control
faulty – auto parking brake activated " and
the following warning lamps:
and/or fl a s h i n g - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.
6 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r
vehicle.
- Apply the electric parking brake before switchi ng off the engine.