ground clearance Citroen C5 2009.5 (RD/TD) / 2.G Owner's Manual

Page 6 of 314

9
F A M I L I A R I S A T I O N
D A S H B O A R D

1. Sunlight sensor.

2. Soft diffusion air conditioning adjustment knob.

3. Passenger’s airbag.

4. Side window demist vent.

5. Passenger’s air vents.

6. Bonnet release.

7. Hazard warning lamps button.

8. Switch in the glovebox:
- Passenger’s airbag activation/deactivation

9. Glovebox:
- Vehicle document storage
- Audio-video sockets
- Fusebox access fl ap

10. ESP/Parking Sensors/Lane Departure Warning
System controls.

11. Suspension controls:
- Ground clearance adjustment
- Sport mode

12. Armrest with cup-holder.

13. Electric parking brake.

14. Automatic gearbox SPORT/SNOW mode controls.

15. Ashtray with cigar lighter.

16. Gear lever.

17. Storage.

18. Audio and telematics system.

19. Air conditioning controls.

20. Storage.

21. Multifunction screen.

Page 168 of 314

IX
149
D R I V I N G
Vehicle positions
Maximum height
Changing a wheel (not possible if
speed > 6mph (10 km/h)).
Intermediate position
For increased ground clearance (not
possible if speed > 25 mph (40 km/h)).
For use on diffi cult roads when tra-
velling at reduced speed, as well as
on car park ramps.

Position changes may only be
made when the engine is running.
The adjustable ground clearance
meets all types of situation. Apart
from a few specifi c situations, the
vehicle should be in the Normal po-
sition.

 Press once on one of the adjust-
ment controls.
The change in position is indicated
by a message on the instrument
panel screen.
Normal position
If the speed authorised for a particu-
lar position is exceeded, the vehicle
reverts automatically to the normal
position.
Minimum height
To facilitate loading or unloading the
vehicle.
For workshop inspections.
Not to be used in normal driving (not
possible if speed > 6mph (10 km/h)).

Page 169 of 314

IX
150
D R I V I N G
Position not authorised
The instrument panel screen tempo-
rarily displays a message indicating
that this position is not authorised.
The vehicle remains in the autho-
rised position and the instrument
panel screen indicates this position
to you.
Automatic variation of ground clea-
rance
- If your speed exceeds 70 mph (approx. 110 km/h), on a good
road surface, ground clearance
is lowered. The vehicle returns
to its normal position if the road
surface deteriorates or if your
speed is lower than 55 mph (ap-
prox. 90 km/h).
- At low or medium speed, if the road surface is poor, ground
clearance is increased. The ve-
hicle returns to its normal posi-
tion as soon as conditions allow.
- On switching off the ignition, the ground clearance is reduced to
the parking position

For your safety if you are operat-ing underneath the vehicle, you
must support the vehicle with
axle stands.

Page 186 of 314

XI
!
168
P R A C T I C A L I N F O R M A T I O N
Removing a wheel

 Park the vehicle on stable, fi rm
ground that is not slippery. apply
the parking brake.

 If your vehicle is equipped with
"Hydractive III+" suspension,
with the engine running at idle,
adjust the ground clearance to
its maximum height.

 Switch off the ignition and en-
gage fi rst gear or reverse gear
depending on any slope (for a
vehicle with automatic gearbox,
select position P ).

 If your vehicle is fi tted with
"Hydractive III+" suspension,
position the chock, whichever di-
rection the gradient may be in, in
front of the front wheel diametri-
cally opposite to the one to be
replaced.
 Position the jack at one of the
four jacking-points provided
on the underbody close to the
wheels, then use the wheelbrace
to unwind the jack until it reaches
the ground.

 Remove the protector from each
bolt using tool 3 .

 Slacken the wheel bolts.
Before positioning the jack:

 Always adjust the vehicle’s
ground clearance to the "maxi-
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehicle
(do not use the hydraulic ad-
justments),


Immobilise your vehicle on hori-
zontal, stable and non-slippery
ground,

 Ensure that any passengers
have left the vehicle and are in
a safe place .
Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
specifi c to your vehicle. Do not use
them for any other applications.
Have the original wheel repaired
and refi tted as soon as possible.

 Continue to extend the jack until
the wheel is a few centimetres
off the ground.

 Undo the bolts, remove the wheel.

Page 187 of 314

XI
!
169
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel

 Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.

 Screw in the bolts but do not fully
tighten them.

 Lower the jack and remove it.

 Tighten the wheel bolts, using
the wheelbrace.

 Refi t the protectors on the bolts.

 Return the ground clearance to
the normal position.

 Ensure the tyre pressure is correct
and have the balancing checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Security bolts
Each wheel is equipped with one
security bolt.
To remove it:

 Remove the protector using tool 3 .

 Use the security socket with the
wheelbrace. If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from a
CITROËN dealer.

Page 188 of 314

XI
!
169
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel

 Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.

 Screw in the bolts but do not fully
tighten them.

 Lower the jack and remove it.

 Tighten the wheel bolts, using
the wheelbrace.

 Refi t the protectors on the bolts.

 Return the ground clearance to
the normal position.

 Ensure the tyre pressure is correct
and have the balancing checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Security bolts
Each wheel is equipped with one
security bolt.
To remove it:

 Remove the protector using tool 3 .

 Use the security socket with the
wheelbrace. If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from a
CITROËN dealer.