display Citroen C5 2012 (RD/TD) / 2.G Owner's Guide

III
53
COMFORT

2a-2b. Temperature adjustment
Control via the manual controls


)
Press one of the controls, with
the exception of temperature
regulation 2a
and 2b
. The indi-
cator lamps A
in the "AUTO"

controls go off.
It is possible to adjust one or more
functions manually while leaving the
other functions in automatic mode.
Switching to manual mode may re-
sult in discomfort (temperature, hu-
midity, odour, condensation) and
may not provide optimum comfort.
To return to "AUTO"
mode, press
controls 1a
and 1b
. The indicator
lamps A
come on.
3a-3b. Air distribution adjustment

)
Press control 3b
to change the
distribution of the air fl ow on the
passenger's side.
The indicator lamps corresponding
to the distribution chosen come on:


- Windscreen and front side win-
dows.

- Front ventilation (central and
side vents and air diffusion grille
if open) and rear ventilation.

- Front and rear footwells.
Simultaneous display of the distribu-
tion of air to the windscreen and side
windows and of front and rear venti-
lation is not possible.

)
Turn control 2a
to change the
temperature on the driver's side
and control 2b
to change the
temperature on the passenger's
side: to the right to increase the
temperature or to the left to re-
duce it.
The setting required is displayed.
The value indicated on the display
corresponds to a level of comfort
and not to a temperature in degrees
Celsius or Fahrenheit, depending on
the screen confi guration.
A setting around the value 21
usually
provides optimum comfort. However,
depending on your requirements, a
setting between 18 and 24 is normal.
On entering the vehicle, the interior
temperature may be much colder (or
warmer) than is comfortable. There
is no need to change the tempera-
ture displayed in order to quickly ob-
tain the level of comfort required.
The automatic regulation of the air
conditioning will use its maximum
performance settings to correct the
temperature difference as quickly as
possible.

)
Press control

3a
to change
the distribu-
tion of the air
fl ow on the
driver's side.

III
55
COMFORT
When starting with the engine
cold, air fl ow will reach its opti-
mum level gradually to prevent an
excessive distribution of cold air.
When entering the vehicle after it
has been parked for a fairly long
period, if the interior temperature
is very different from your comfort
setting there is no need to change
the temperature displayed in or-
der to quickly reach the level of
comfort required. The system
automatically uses its maximum
performance to correct the differ-
ence in temperature as quickly as
possible.
The water resulting from the air
conditioning condensation is dis-
charged via an opening provided
for this purpose; therefore, a pud-
dle of water may form underneath
the vehicle when stationary.
In all seasons, if the weather is
cool, the air conditioning is use-
ful as it removes the humidity
from the air and the condensa-
tion. Avoid driving for prolonged
periods with the air conditioning
switched off.
9. Front demisting - defrosting
In certain cases, the
"AUTO"
mode may not
be suffi cient to demist
or defrost the windows
(humidity, several pas-
sengers, ice).


)
Press control 9
to clear the win-
dows quickly. The indicator lamp
comes on.
This system controls the temperature,
air fl ow and intake and distributes the
ventilation to the windscreen and front
side windows.
Resuming manual control exits from
the "Demisting" mode. It must be
cancelled as soon as possible to
permit renewal of the air in the pas-
senger compartment and demisting.
Pressing one of the controls 1a

and 1b
returns the system to the
"AUTO"
mode.
8. Rear demisting - defrosting

Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current consump-
tion reduces fuel consumption.

The heated rear screen
operates independently
of the air conditioning
system.


)
Press control 8
, with the en-
gine running, to demist the rear
screen and the mirrors. The indi-
cator lamp comes on.
Demisting is switched off automatical-
ly to avoid excessive consumption of
current and depending on the exterior
temperature.
It may be stopped by pressing
control 8
again or when the engine
is switched off.
In this latter case, the demisting re-
sumes if the engine is switched on
again within one minute.






With Stop & Start, when demisting
has been activated, the STOP mode
is not available.

III
56
COMFORT
PROGRAMMABLE HEATING

The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
the coolant circuit in order to benefi t
from an optimum engine operating
temperature from the time the en-
gine is switched on.
The programmable heating system
is switched on using the long range
remote control. Activation can be im-
mediate or deferred by means of a
programming function.

Programming remote control

The heating system programming
remote control consists of the fol-
lowing buttons and displays:


1.
Scrolling functions menu but-
tons.

2.
Function indicators: clock, tem-
perature, operating time, pro-
grammed time, heater operation,
heating management symbols.

3.
Digital displays: time, tempera-
ture, duration of operation, pro-
grammed time or level of heating.

4.
Off button.

5.
On button.



Displays on the remote
control screen

Press the buttons 1
in succession to
display the functions.
The fi rst press of the left-hand or
right-hand button displays the time.
Next, the left-hand button permits
access to the programming time then
to the level of heating (C1 to C5).
The right-hand button permits ac-
cess to the passenger compartment
temperature then to the duration of
operation of the heater if it is to be
switched on immediately.

If a malfunction of the program-
mable heating system occurs,
contact a CITROËN dealer
or a

qualifi ed workshop

.




Displaying the functions


The passenger compartment tem-
perature information is only avail-
able when the engine is off.

III
57
COMFORT

Setting the time

Once the time has been displayed,
by means of the buttons 1
, press
buttons 4
and 5
simultaneously with-
in 10 seconds.

Immediate activation

Press button 5
(ON) until the mes-
sage "OK"
appears.
When the signal has been received,
the message "OK"
is displayed
along with the duration of operation. Press the buttons 1
to display the
duration of operation.
This symbol fl ashes.
Set the time using the buttons 1
.
Press buttons 4
and 5
simultane-
ously to save it.
This symbol is displayed (fi xed).

The heater starts and this
symbol is displayed.
To deactivate the function, press
button 4
(OFF) until the message
"OK"
appears.
This symbol is switched off.

When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.



Setting the duration of
operation
This symbol is displayed.
Once the duration of operation has
been displayed, press buttons 4
and 5

simultaneously within 10 seconds.
This symbol fl ashes.
Set the duration by pressing the
buttons 1
(adjustment in steps of
10 mins and max value 30 mins).
Press buttons 4
and 5
simultaneous-
ly to save the duration of operation.
This symbol is displayed (fi xed).


The factory setting value is 30 minutes.

III
58
COMFORT

Programming the heating

You must programme your depar-
ture time in order for the system to
calculate the optimum heater start
time automatically.

Programming the departure time
Press the buttons 1
to display the
programming time.
Activation - deactivation
Once the programming time has
been displayed by means of the but-
tons 1
, press button 5
(ON) until the
message "OK"
appears.
This symbol is displayed.
Once the programming time has been
displayed, press buttons 4
and 5
si-
multaneously within 10 seconds.
This symbol fl ashes.
Set the time by pressing the buttons 1

and press buttons 4
and 5
simultane-
ously to save it.
This symbol is displayed (fi xed).

This symbol is displayed
when the heater starts.

HTM: Heat Thermo Management.

When the signal has been received,
the message "OK"
is displayed
along with the symbol "HTM"
.

To deactivate the programming,
press button 4
(OFF) until the mes-
sage "OK"
appears.

The symbol "HTM"
is switched
off.


When carrying out these opera-
tions, if the message "FAIL"
ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
Switching off the heating
Press button 5
(ON).
The symbol "HTM"
remains
on.

Changing the level of heating
The system offers 5 levels
of heat-
ing (from the lowest level C1
to the
highest level C5
).
Once the level of heating has been
displayed by means of the buttons 1
,
press buttons 4
and 5
simultane-
ously.
The letter "C"
fl ashes.
Set the level of heating by pressing
the buttons 1
.
Press buttons 4
and 5
simultane-
ously to save the level selected. The
letter "C"
is displayed (fi xed).

The factory pre-sets are replaced
by the new settings entered. The
programmed times are stored until
the next time they are changed.
When the departure time is acti-
vated, the level of heating cannot
be changed. The departure time
must be deactivated fi rst.

III
!
59
COMFORT

Changing the battery
The remote control is supplied by a
6V-28L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the
battery.
The remote control must then be re-
initialised, see below.
Always switch off the program-
mable heating while fi lling with
fuel to avoid any risk of fi re or ex-
plosion.
To avoid any risk of poisoning and
asphyxiation, the programmable
heating must not be used, even
for short periods, in an enclosed
space such as a garage or work-
shop which is not equipped with
an exhaust gas extraction system.
Do not park the vehicle on an
infl ammable surface (dry grass,
dead leaves, paper…), there is a
risk of fi re.
The programmable heating sys-
tem is supplied by the vehicle's fuel
tank. Before use, ensure that the
quantity of fuel remaining is suf-
fi cient. If the fuel tank is at the re-
serve, we strongly advise that you
do not programme the heating.

Do not discard the used batter-
ies, take them to an approved
collection point.

Reinitialising the remote control
If the vehicle's battery is disconnect-
ed or the remote control's battery is
replaced, the remote control must
be reinitialised.
After switching on the power, press
button 4
(OFF) for 1 second within
the next 5 seconds. If the operation
has taken place correctly the mes-
sage "OK"
is displayed on the re-
mote control screen.
If a problem occurs, the message
"FAIL"
appears. Repeat the opera-
tion.

An adaptation of your programma-
ble heating allows you to pre-heat
your vehicle's passenger compart-
ment. Contact a CITROËN dealer
or a qualifi ed workshop.
The interior volumetric protection
alarm movement sensor may be
disturbed by the fl ow of air from
the programmable heating when
it is in operation.
To avoid any unexpected trigger-
ing of the alarm during use of the
programmable heating, it is ad-
visable to deactivate the interior
volumetric protection.

V
86
VISIBILITY
EXTERIOR LIGHTING
CONTROLS
Control stalk for the selection and
control of the various front and rear
lamps providing the vehicle's lighting.

Main lighting

The various front and rear lamps of
the vehicle are designed to adapt
the driver's visibility progressively in
relation to the climatic conditions:


- sidelamps, to be seen,

- dipped beam headlamps to see
without dazzling other drivers,

- main beam headlamps to see
clearly when the road is clear.



Additional lighting

Other lamps are fi tted to fulfi l the re-
quirements of particular driving con-
ditions:


- a rear foglamp to be seen from a
distance,

- front foglamps for even better
forward vision,

- directional headlamps for im-
proved visibility when cornering,

- daytime running lamps to be
seen during the day.



Settings

Various automatic lighting control
modes are also available depending
on options:


- daytime running lamps,

-
automatic illumination of headlamps,


- directional lighting,

- guide-me-home lighting.



Manual controls

Lamps off.





Automatic illumination of
headlamps.
Sidelamps.
Dipped headlamps or
main beam headlamps.

B.

Stalk for switching headlamps: pull
the stalk towards you to switch the
lighting between dipped and main
beam headlamps.
In the lamps off and sidelamps
modes, the driver can switch on the
main beam headlamps temporarily
("headlamp fl ash") by maintaining a
pull on the stalk.

Displays

Illumination of the corresponding indicator
lamp in the instrument panel confi rms that
the lighting selected is on.

The lighting is controlled directly by
the driver by means of the ring A

and the stalk B
.
A.
Main lighting mode selection ring:
turn it to position the symbol re-
quired facing the mark.
In some weather conditions (e.g. low
temperature or humidity), the pre-
sence of misting on the internal sur-
face of the glass of the headlamps
and rear lamps is normal; it disap-
pears after the lamps have been on
for a few minutes.

VIII
11 5
SAFETY
TYRE UNDER-INFLATION DETECTION
System which automatically checks the pressures of the tyres while driving.


Tyre pressures OK
display

Choice of detection

This function provides warning of
tyres that are under-infl ated or punc-
tured.

Automatic detection
Sensors monitor the tyre pressures.
In the event of an anomaly, a mes-
sage will appear in the instrument
panel screen.

Driver request detection
You can check the tyre pressures at
any time.


)
Press on button A
(CHECK); the
information will be displayed in
the instrument panel screen.



)
Press on button A
(CHECK).
The system indicates to you that the
tyres are correctly infl ated.
This information is only available on
request by the driver.


Under-inflated tyre


automatic detection


detection on request


Automatic detection:
A message indicates which tyre is
under-infl ated.

Driver request detection:
The vehicle outline indicates the
under-infl ated tyre(s).
The message is accompanied by il-
lumination of the SERVICE
warning
lamp and an audible beep.


)
Check the tyre pressures as
soon as possible.

IX
!!
127
DRIVING
ELECTRIC PARKING BRAKE
The electric parking brake combines
2 operating modes:


- AUTOMATIC

Automatic application when the
engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),

- MANUAL

Manual application / release of
the parking brake is always pos-
sible by pulling control lever A

while pressing the brake pedal.


Automatic operation


Application with the engine off
With the vehicle stationary, the park-
ing brake is automatically applied
when the engine is switched off.

The application of the parking brake
is confi rmed by:
Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by pulling

on control lever A
.
The application of the parking brake
is confi rmed by:

- warning lamp P
in the con-
trol lever A
coming on,
Before leaving the vehicle,
check that warning lamp P

and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- display of a message "parking
brake on" in the instrument panel
screen.
The noise of operation will confi rm to
you the application/ release of your
electric parking brake.

- warning lamp P
in the con-
trol lever A
coming on,

- display of a message "parking
brake on" in the instrument panel
screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P

and the warning lamp in the
instrument panel are on fi xed (not
fl ashing).
-
this warning lamp in the in-
strument panel coming on,

- this warning lamp in the in-
strument panel coming on,

IX!
!
128
DRIVING

Release
The electric parking brake releases
automatically and progressively

when you press the accelerator:


)
with a manual gearbox
(fi rst
gear or reverse gear engaged),
press down fully on the clutch
pedal then press on the accele-
rator pedal and move off.

)
with an automatic gearbox
, ac-
celerate with the selector in posi-
tion D
, M
or R
.
Full release of the parking brake is
confi rmed by:


- warning lamp P
in the
control lever A
going off,

- display of a message "parking
brake off" in the instrument panel
screen.
When stationary, with the engine
running, do not press the accelera-
tor pedal unnecessarily (particularly
when starting the engine, including
in neutral), as you may release the
parking brake.
Do not place any object (packet of
cigarettes, telephone...) between
the gear lever and the electric park-
ing brake control.
Activation / Deactivation of the
automatic functions
Depending on the country of sale,
automatic application when switch-
ing off the engine and automatic
release when moving off can be de-
activated. The activation / deactiva-
tion is done in the instrument panel
screen confi guration menu. Select
"Vehicle parameters / Comfort / Auto
parking brake".
Deactivation of these func-
tions is signalled by this
warning lamp in the instru-
ment panel.
With the automatic functions deac-
tivated, the parking brake must be
applied and released manually.
In some special circumstanc-
es, with the engine not run-
ning, (towing, icy conditions...) the
automatic parking brake can be
released manually, with the key in
the running position.
Manual operation

Manual application / release of the
parking brake is always possible.

Application
With the vehicle stationary, to apply the
parking brake whether the engine is
running or off, pull
on control lever A
.
The application of the parking brake
is confi rmed by:


- warning lamp P
in the con-
trol lever A
coming on,

- display of a message "parking
brake on" in the instrument panel
screen.
When the driver’s door is opened
with the engine running, a mes-
sage is displayed accompanied
by an audible signal if the parking
brake has not been applied.
-
this warning lamp in the in-
strument panel coming on,

- this warning lamp in the in-
strument panel going off,
If the confi guration menu does not
have the option to activate / deac-
tivate the automatic functions, this
can be done by a CITROËN dealer
or a qualifi ed workshop.