ESP Citroen C5 DAG 2008.5 (RD/TD) / 2.G Owner's Manual

Page 9 of 306

29
1
I N S T R U M E N T S a n d C O N T R O L S
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located
in the centre of the fascia, permits
deactivation of the system. This is
confi rmed by continuous lighting of
this warning light and of the indicator
light on the button.

From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lights
indicates the occurrence of a fault
requiring intervention on the part of
the driver.
Any fault resulting in the displaying
of a warning light must be the sub-
ject of further diagnostics by reading
the associated message on the mul-
tifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.
Front passenger's airbag
activation
If this comes on temporarily when
the ignition is switched on, it indi-
cates that the front passenger's air-
bag is active.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the multifunction screen.

Page 10 of 306

29
1
I N S T R U M E N T S a n d C O N T R O L S
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located
in the centre of the fascia, permits
deactivation of the system. This is
confi rmed by continuous lighting of
this warning light and of the indicator
light on the button.

From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lights
indicates the occurrence of a fault
requiring intervention on the part of
the driver.
Any fault resulting in the displaying
of a warning light must be the sub-
ject of further diagnostics by reading
the associated message on the mul-
tifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.
Front passenger's airbag
activation
If this comes on temporarily when
the ignition is switched on, it indi-
cates that the front passenger's air-
bag is active.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the multifunction screen.

Page 11 of 306

29
1
I N S T R U M E N T S a n d C O N T R O L S
Deactivation warning lights
If one of the following warning lights
comes on, this confi rms that the
corresponding system has been
switched off intentionally.
Passenger's air bag system
deactivation Dynamic stability control
(ESP/ASR) deactivation
The ESP/ASR system is put
into service automatically
when the vehicle is started.
A specifi c button, located
in the centre of the fascia, permits
deactivation of the system. This is
confi rmed by continuous lighting of
this warning light and of the indicator
light on the button.

From approximately 30 mph (50 km/h),
the system is reactivated automatically. Warning lights
Diesel engine pre-heating
Wait until this is switched off before
operating the starter.
When the engine is running or the
vehicle is moving, the lighting of
one of the following warning lights
indicates the occurrence of a fault
requiring intervention on the part of
the driver.
Any fault resulting in the displaying
of a warning light must be the sub-
ject of further diagnostics by reading
the associated message on the mul-
tifunction display.
Should you encounter any prob-
lems, do not hesitate to contact a
CITROËN dealer.
Front passenger's airbag
activation
If this comes on temporarily when
the ignition is switched on, it indi-
cates that the front passenger's air-
bag is active.
The passenger's air bag
system is put into service
automatically when the ve-
hicle is started.
A specifi c control, located in the glove
box, permits deactivation of the sys-
tem. This is confi rmed by continuous
lighting of this warning light on the
instrument panel or a message on
the multifunction screen.

Page 12 of 306

30
1
I N S T R U M E N T S a n d C O N T R O L S
Lighting is associated
with another warning
light:
Service If this warning light
comes on, it indicates
the occurrence of a
problem in one of the
systems which does not have a spe-
cifi c warning light.
In order to identify it, consult the mes-
sage on the multifunction display.
The warning light only comes on tem-
porarily in the case of the following
minor faults:
- incorrect closing of the doors, boot, rear screen and bonnet,
- fl at remote control battery,
- insuffi cient tyre pressure,
- the saturation of the particle emission fi lter (Diesel).
In the case of major faults, the warn-
ing light remains on until the operating
fault is rectifi ed, contact a CITROËN
dealer as soon as possible. Braking
If this comes on, it indicates
the occurrence of a fault in
one of the braking systems:
- signifi cant drop in the level in the circuit,
- electronic brake force distribution (EBFD) faulty (simultaneous light-
ing of the ABS warning light),
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.
Parking brake
When stationary, the perma-
nent lighting of this warning
lamp confi rms that the park-
ing brake is applied.
If this warning lamp fl ashes, it indicates
a fault with its application or release.
Consult a CITROËN dealer.
With the engine running, and when
displayed at the same time as the

STOP warning lamp, it indicates that
the brake fl uid level is too low. Electronic parking brake fault
This warning lamp comes
on if there is a fault with the
electronic parking brake.
Electronic parking brake
- deactivation of automatic
functions This warning lamp comes
on if the "automatic lock-
ing" (upon switching off the
ignition) and the "automatic
unlocking" functions are de-
activated or faulty.
Dynamic stability control
(ESP/ASR) The ESP/ASR system is put
into service automatically
when the vehicle is started.
Unless the system has been deacti-
vated, if this warning light comes on
continuously, accompanied by a mes-
sage on the instrument panel screen,
switching on of the SERVICE warning
light and an audible signal, this indi-
cates the occurrence of a fault in the
ESP/ASR system.
Central alert
- punctured wheel,
- braking,
- coolant temperature,
stop the vehicle immediately and as
safely as possible.
Consult a CITROËN dealer.
Anti-lock braking system (ABS) If this comes on, it indicates
the occurrence of a fault in
the anti-lock braking system.
However, this does not prevent op-
eration of the vehicle's assisted
braking. If this warning lamp comes on, stop
immediately and contact a CITROËN
dealer.
Consult a CITROËN dealer.

Page 13 of 306

31
1
I N S T R U M E N T S a n d C O N T R O L S
Engine autodiagnostics system If this comes on, it indicates
the occurrence of a fault in
the engine management
system.
If it fl ashes, it indicates the occurrence of
a fault in the emission control system.
Maximum coolant temperature If this comes on, it indicates
that the temperature in the
cooling system is too high.
Stop the vehicle immediately
and as safely as possible.
Check the coolant level.
If the level is low, contact a CITROËN
dealer.
Fuel low
If this comes on, it indicates
that the range remaining
is approximately 30 miles
(50 km).
It may be less than this in certain
driving conditions and depending on
the engine.
The capacity of the tank is approxi-
mately 71 litres. Battery charge
If this comes on, it indi-
cates the occurrence of a
fault in the battery charging
circuit (dirty or loose termi-
nals, slack or cut alternator
belt...).
Seat belt not fastened/
unfastened *
* According to country.
This warning lamp lights
up on the instrument panel
to remind the driver and all
passengers that they must
fasten their seat belt.
It is linked to the seat belt informa-
tion given by the roof console. Seat belt non-fastening/
unfastening
This warning lamp
informs you of the
non-fastening and
unfastening of the
driver and passenger seat belts.
The lit up positions represent the
passengers whose seat belts are
not fastened/unfastened.
Driver’s seat belt not fastened:
- The warning lamp lights up be- tween 0 and 12 mph (20 km/h).
Above 12 mph, it fl ashes accompa-
nied by a sound signal for around
120 seconds.
Front and rear passenger seat belts
not fastened:
-
When the ignition is switched on,
the points corresponding to the seat
positions with seat belts not fas-
tened remain lit up for 30 seconds.
Seat belts unfastened during the
journey:
- The point corresponding to the seat position with seat belt un-
fastened lights up between 0 and
12 mph (20 km/h). Above 12 mph,
it fl ashes accompanied by a sound
signal for around 120 seconds.
The sound signal stops when the
seat belt is re-fastened or if a door
is opened.

Page 21 of 306

39
2
M U L T I F U N C T I O N D I S P L A Y S
16/9 COLOUR DISPLAY (WITH MYWAY)
Displays on the screen
It displays the following information
automatically and directly:
- the time,
- the date,
- the altitude,
- the exterior temperature (the val-ue displayed fl ashes if there is a
risk of ice),
- the audio functions,
- the satellite navigation system information. Controls
From the MyWay control panel, to
select one of the applications:

 press the dedicated "RADIO" ,

"MUSIC" , "NAV" , "TRAFFIC" ,

"SETUP" or "PHONE" button to
gain access to the correspond-
ing menu,

 turn the navigator to move the
selection,

 press the navigator to confi rm
the selection,
or

 press the "ESC" button to aban-
don the current operation and re-
turn to the previous display.
* According to country. For further details concerning
these applications, refer to the
"Audio Equipment" section or to
the specifi c user guide given to
you with the other owner's docu-
ments. "SETUP" menu

 Press the "SETUP" button to
gain access to the "SETUP"
menu. This allows you to select
from the following functions:
- "Languages",
- "Date and time",
- "Display",
- "Units",
- "System parameters".
Languages
This menu allows you to select the lan-
guage used by the display: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Polski, Portugues,
Türkçe * .

Page 23 of 306

41
2
M U L T I F U N C T I O N D I S P L A Y S
16/9 HIGH DEFINITION COLOUR DISPLAY (WITH NAVIDRIVE 3D)
Displays on the screen
It displays the following information
automatically and directly:
- the time,
- the date,
- the altitude,
- the exterior temperature (the val-ue displayed fl ashes if there is a
risk of ice),
- the audio functions,
- the telephone and address book information,
- the satellite navigation system information. Controls
From the NaviDrive 3D control pan-
el, to select one of the applications:

 press the dedicated "RADIO" ,

"MEDIA" , "NAV" , "TRAFFIC" ,

"ADDR BOOK" or "SETUP"
button to gain access to the cor-
responding menu,

 turn the navigator to move the
selection,

 press the navigator to confi rm
the selection,
or

 press the "ESC" button to aban-
don the current operation and re-
turn to the previous display. For further details concerning
these applications, refer to the
"Audio Equipment" section or to
the specifi c user guide given to
you with the other owner's docu-
ments.

Page 24 of 306

42
2
M U L T I F U N C T I O N D I S P L A Y S * According to country.
"SETUP" menu

 Press the "SETUP" button to gain
access to the "SETUP" menu.
This allows you to select from
the following functions:
- "Languages and voice func- tions",
- "Date and time",
- "Display",
- "Units",
- "System parameters".
Languages and voice functions
This menu allows you to:
- select the language used by the display (Deutsch, English,
Espanol, Français, Italiano,
Nederlands, Polski, Portugues,
Türkçe * ),
- select the voice recognition pa- rameters (activation/deactiva-
tion, advice on use, personal
voice programming, etc.),
- set the volume of the voice syn- thesiser. Date and time
This menu allows you to set the date
and time, the format of the date and
the format of the time (refer to the
"Audio Equipment" section or to the
specifi c user guide given to you with
the other owner's documents).
Display
This menu allows you to set the
brightness of the screen, the screen
colour scheme and the colour of the
map (day/night or auto mode).
System parameters
This menu allows you to restore the
factory confi guration, display the
software version and activate the
scrolling text.
For safety reasons, it is impera-
tive that confi guration of the mul-
tifunction displays by the driver is
carried out when stationary.

Page 27 of 306

45
3
C O M F O R T
AUTOMATIC AIR CONDITIONING (MONO ZONE)
This is the normal sys-
tem operating mode.
In accordance with the
level of comfort cho-
sen, pressing this con-
trol, confi rmed by the
switching on of indicator light A , per-
mits automatic and simultaneous con-
trol of all of the following functions:
- Air fl ow.
- Temperature in the passenger compartment.
- Air distribution.
- Air intake.
- Air conditioning.
1. Automatic operation
It is advisable to leave all of the
vents open.
Simply pressing one of the con-
trols, with the exception of control

2 , switches the system to manual
mode.
Indicator light A switches off. 2. Temperature adjustment
Turn control 2 to change
the temperature:
- Clockwise to in- crease the temper-
ature.
- Anticlockwise to reduce the tem- perature.
The setting required is displayed.
The value indicated on the display
corresponds to a level of comfort
and not to a temperature in degrees
Celsius or Fahrenheit, depending on
the choice of confi guration validated
on the display.
A setting around the value 21 usually
makes it possible to obtain optimum
comfort. However, depending on your
requirements, a setting between 18
and 24 is usual.
On entering the vehicle, the interior
temperature may be much colder
(or warmer) than is comfortable.
There is no need to change the tem-
perature displayed in order to obtain
rapidly the level of comfort required.
The automatic regulation of the air
conditioning will use its maximum
performance settings to correct the
temperature difference as quickly as
possible.

Mono zone: this is the overall regu-
lation of the temperature, distribu-
tion and fl ow of air in the passenger
compartment.
The symbols and messages associat-
ed with the automatic air conditioning
controls appear on the multifunction
display.

1. Automatic operation

2. Temperature adjustment

3. Air distribution adjustment

4. Activation/deactivation of the air
conditioning

5. Air fl ow adjustment

6. Front demisting - de-icing

7. Rear demisting - de-icing

8. Air recirculation - intake of exte-
rior air

9. Display

Page 28 of 306

46
3
C O M F O R T
Control via the manual controls
It is possible to adjust one or more
functions manually, while leaving the
other functions in automatic mode.

 Press one of the controls, with
the exception of that which regu-
lates the temperature 2 . Indicator
light A switches off.
Switching to manual mode may re-
sult in discomfort (temperature, hu-
midity, odour, condensation) and is
not advantageous to comfort.
To return to automatic mode, press
the "AUTO" control.
3. Air distribution adjustment
 Press the controls 3
to change the distri-
bution of the air fl ow. 4. Air conditioning
The air conditioning will only oper-
ate when the engine is running. The
air blower control (air fl ow adjust-
ment) must be active to obtain air
conditioning.
Switching off the ventilation

 Turn control 5 to the
left until the fl ow of
air stops.

 Press control 4 .
Indicator light B
comes on.
5. Air fl ow adjustment
 Turn control 5 to the
right to increase the
air fl ow or to the left
to reduce it.
6. Front demisting - de-icing
In certain cases, the

"AUTO" mode may not
be suffi cient to demist or
de-ice the windows (hu-
midity, several passen-
gers, ice).

 Press control 6 to clear the win-
dows quickly. The indicator light
comes on.
The
"OFF" symbol is displayed on
the multifunction display.
This action switches off the display
and the indicator lights.
It deactivates all of the system's
functions, with the exception of the
rear screen demisting.
The temperature-related comfort is
no longer controlled (temperature,
humidity, odour, condensation).
Avoid driving for too long with the air
conditioning off.
In order to be effective, the air con-
ditioning must be used with the win-
dows closed.
Deactivating the air conditioning may
result in discomfort (temperature,
humidity, odour, condensation).
The indicator lights corresponding to
the distribution chosen come on:
- Windscreen and front side win- dows.
- Front ventilation (central and side vents and air diffusion grille
if open) and rear ventilation.
- Front and rear footwells.
Simultaneous displaying of the dis-
tribution of air to the windscreen and
side windows and of front and rear
ventilation is not possible. The air fl ow level is indicated by the
progressive lighting of the blocks of
the bar graph on the control panel
display
9 .
To prevent condensation and dete-
rioration of the quality of the air in
the passenger compartment, ensure
that an adequate fl ow of air is main-
tained.
To reactivate the air conditioning:

 Press control 1 .

Page:   1-10 11-20 21-30 31-40 41-50 ... 50 next >