Citroen C5 DAG 2009.5 (RD/TD) / 2.G Owner's Manual

XI
!
169
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel

 Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.

 Screw in the bolts but do not fully
tighten them.

 Lower the jack and remove it.

 Tighten the wheel bolts, using
the wheelbrace.

 Refi t the protectors on the bolts.

 Return the ground clearance to
the normal position.

 Ensure the tyre pressure is correct
and have the balancing checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Security bolts
Each wheel is equipped with one
security bolt.
To remove it:

 Remove the protector using tool 3 .

 Use the security socket with the
wheelbrace. If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from a
CITROËN dealer.

XI
!
169
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Your vehicle may be fi tted with a
spare wheel which is different to
those on the vehicle. When fi tting
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
When refi tting the original wheel,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel

 Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.

 Screw in the bolts but do not fully
tighten them.

 Lower the jack and remove it.

 Tighten the wheel bolts, using
the wheelbrace.

 Refi t the protectors on the bolts.

 Return the ground clearance to
the normal position.

 Ensure the tyre pressure is correct
and have the balancing checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Security bolts
Each wheel is equipped with one
security bolt.
To remove it:

 Remove the protector using tool 3 .

 Use the security socket with the
wheelbrace. If your vehicle is fi tted with a
spare wheel of a different size
to those on the vehicle, you
must not exceed 50 mph (80 km/h)
whilst using the spare wheel.
The wheel bolts are specifi c to the
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the security bolt socket. This will
enable you to obtain a replace-
ment security bolt socket from a
CITROËN dealer.

XI
!
170
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB Headlamps
Model with Xenon headlamps (D1S)

1. Sidelamps: W5W

2. Dual-function Xenon headlamps
(dipped/main): D1S

3. Angular lighting: HP19

4. Daytime running lamps: HP24
For the maintenance of the front
headlamp unit and the changing of
HP19, D1S and HP24 bulbs, contact a CITROËN dealer.
Risk of electrocution
Xenon bulbs must be replaced by a
CITROËN dealer.
You are advised to change both
D1S bulbs at the same time, if one
of them has failed.
The headlamps are fi tted with
polycarbonate glass with a
protective coating:

 do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,

 use a sponge and soapy water,

 when using a high pressure
washer on persistent marks, do
not direct at the lamps or their
outlines for too long, so as not to
damage their protective coating
and seals.

 Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a halogen bulb should
only be done after the headlamp
has been switched off for a few
minutes (risk of serious burns).
It is imperative to use only anti-ultra-
violet (UV) type bulbs in order not to
damage the headlamp.

XI
171
P R A C T I C A L I N F O R M A T I O N
Main beams

 Remove the protective cap A .

 Disengage the retaining spring.

 Remove the bulb and replace it,
paying attention to the direction
of fi tting.

 Refi t the retaining spring.

 Refi t the protective cap A .
Model with halogen headlamps

1. Main beams: H1

2. Sidelamps: W5W

3. Dipped beams: H7

4. Directional lighting: H7

5. Daytime running lamps: HP24
For the maintenance of the front
headlamp unit and changing HP24
bulbs, contact a CITROËN dealer.
Sidelamps

 Remove the protective cap A .

 Pull the bulb holder to remove it.

 Replace the bulb and refi t the
bulb holder.

 Refi t the protective cap A .

XI
172
P R A C T I C A L I N F O R M A T I O N
Sidelamps

 Remove the protective cap A .

 Pull the bulb holder to remove it.

 Replace the bulb and refi t the
bulb holder.

 Refi t the protective cap A . Dipped beam

 Remove the protective cap B .

 Disconnect the connector by
pressing it between the thumb
and index fi nger.

 Free the bulb from its two metal
clamps.

 Take out the bulb.

 Replace the bulb, exerting a
slight axial force.

 Refi t the connector, until it is all
the way in.

 Refi t the protective cap B . Directional lamp

 Remove the protective cap C .

 Disconnect the connector by
pressing it between the thumb
and index fi nger.

 Free the bulb from its two metal
clamps.

 Take out the bulb.

 Replace the bulb, exerting a
slight axial force.

 Refi t the connector, until it is all
the way in.

 Refi t the protective cap C .

XI
173
P R A C T I C A L I N F O R M A T I O N
Front foglamp

 Remove the fi xing screw of
cover A using a torx tool, tip the
cover over and remove.

 Remove the fi xing screw of
lamp B using a torx tool and pull
the headlamp unit to remove it
from the bumper.

 Disconnect the connector D .
 Remove the bulb by performing
a quarter of a turn.

 Replace the bulb.

 Refi t the connector D .

 Refi t the headlamp unit in the
bumper.

 Screw the headlamp unit in.

 Position the cover using its guides
and screw in.

Bulbs: H8
Direction indicators

 Remove the fi xing screw of
cover A using a torx tool, tip the
cover over and remove.

 Remove the fi xing screw of
lamp B using a torx tool and pull
the headlamp unit to remove it
from the bumper.

 Detach the bulb C by pressing
on bars 1 and 2 .

 Disconnect the connector (pull
whilst pressing on the grey
tongue using a fl at screwdriver).

 Replace the bulb.

 Refi t the connector (push the
grey tongue in well).

 Refi t the headlamp unit in the
bumper.

 Screw the headlamp unit in.

 Position the cover using its
guides and screw in.

Bulbs: HP24W

XI
174
P R A C T I C A L I N F O R M A T I O N
The side repeater is sealed.
If the bulb is faulty, replace the side
repeater.
Consult a CITROËN dealer.
Side repeaters
Rear lamps (Saloon)
Identify the failed bulb.

1. Stop lamps and sidelamps:
P21 W/5W

2. Sidelamps: R5W

3. Reversing lamp: H21W

4. Foglamps: H21W

5. Direction indicators: P21W
 Open the boot.

 Using a fl at screwdriver, remove
the 3 clips which fi x the trim in
the lamp area.

 Partially remove the trim F .

 Disconnect the connector G .
Boot-mounted lamps

 Detach the bulb holder H .

 Replace the bulb.

 Refi t the bulb holder H .

 Refi t the connector G .

 Replace and fi x the trim F with its
clips.

When refi tting, take care not to
trap the electrical cables.

XI
174
P R A C T I C A L I N F O R M A T I O N
The side repeater is sealed.
If the bulb is faulty, replace the side
repeater.
Consult a CITROËN dealer.
Side repeaters
Rear lamps (Saloon)
Identify the failed bulb.

1. Stop lamps and sidelamps:
P21 W/5W

2. Sidelamps: R5W

3. Reversing lamp: H21W

4. Foglamps: H21W

5. Direction indicators: P21W
 Open the boot.

 Using a fl at screwdriver, remove
the 3 clips which fi x the trim in
the lamp area.

 Partially remove the trim F .

 Disconnect the connector G .
Boot-mounted lamps

 Detach the bulb holder H .

 Replace the bulb.

 Refi t the bulb holder H .

 Refi t the connector G .

 Replace and fi x the trim F with its
clips.

When refi tting, take care not to
trap the electrical cables.

XI
175
P R A C T I C A L I N F O R M A T I O N
Wing-mounted lamps

 Remove the lateral boot trim fl ap A .
To do so, pull it towards the inside
of the boot, then pull it upwards.
 Disconnect connector B .

 Unscrew the 2 fi xings C .

 Remove the lamp from its housing.
 Detach the bulb holder D .

 Replace the bulb.

 Refi t the bulb holder D .

 Place the lamp in its housing.

 Screw in the 2 fi xings C .

 Refi t connector B .

 Refi t the trim A .
You can use the wheelbrace to screw
or unscrew the fi xings C .

XI
176
P R A C T I C A L I N F O R M A T I O N
Boot-mounted lamps

 Open the boot.

 Using a fl at screwdriver, remove
the 3 clips which fi x the trim in
the lamp area.

 Partially remove the trim F .

 Disconnect the connector G .
Rear lamps (Tourer)
Identify the failed bulb.

1. Stop lamps and sidelamps:
P21 W/5W

2. Sidelamps: R5W

3. Reversing lamp: H21W

4. Foglamps: H21W

5. Direction indicators: P21W
 Detach the bulb holder H .

 Replace the bulb.

 Refi t the bulb holder H .

 Refi t the connector G .

 Replace and fi x the trim F with its
clips.