engine Citroen C5 DAG 2009.5 (RD/TD) / 2.G Owner's Manual

Page 11 of 306

I
29
M O N I T O R I N G

Warning lamp is on Cause Action/Observations

Front
foglamps fi xed.
The front foglamps are switched on. Turn the ring on the stalk rearwards
twice to switch off the front foglamps.

Rear
foglamps fi xed.
The rear foglamps are switched on. Turn the ring on the stalk rearwards
to switch off the rear foglamps.

Diesel engine
pre-heating fi xed. The ignition switch is at the 2nd
position (ignition on). Wait until the warning lamp has
switched off before starting. The duration for which the warning lamp is
on is determined by the climatic conditions.

Parking
brake fi xed.
The parking brake is applied or not
properly released. Release the parking brake to switch
off the warning lamp, keeping your
foot on the brake pedal.
Observe the safety recommendations.
For further information on the
parking brake, refer to the "Driving"
section.
fl ashing.
The parking brake is not fully applied
or is released.

Passenger's
airbag
system fi xed. The control switch, located in the
glove box, is in the "
ON " position.
The passenger's front airbag is
activated.
In this case, do not install a rear-
facing child seat. Turn the control switch to the "
OFF "
position to deactivate the front
passenger's airbag.
In this case you can install a rear-
facing child seat.
The passenger's airbag system is
automatically put into service on
starting the vehicle (" ON " position).

Page 14 of 306

I
32M O N I T O R I N G

Warning lamp is on Cause Action/Observations


Anti-lock
Braking System (ABS) fi xed.
The anti-lock braking system has a
fault. The vehicle retains conventional
braking.
Drive carefully at reduced speed
and contact a CITROËN dealer
without delay.

Electric
parking brake fl ashing. The electric parking brake is not
applied automatically. You must stop immediately where it
is safe to do so.
Park on level ground, switch off the
ignition and contact a CITROËN
dealer.

Electric
parking brake fault fi xed. The electric parking brake is faulty. Contact a CITROËN dealer without
delay.
The parking brake can be released
manually.
For further information about the
electric parking brake, refer to the
"Driving" section.


Deactivation of
the automatic
functions of the electric parking brake fi xed.
The "automatic application" (on
switching off the engine) and
"automatic release" functions are
deactivated or faulty. Activate the function (according to
country) via the vehicle confi guration
menu or contact a CITROËN dealer.

Page 15 of 306

I
33
M O N I T O R I N G


Dynamic
stability control
(ESP/ASR) fl ashing. The ESP/ASR regulation is active.
The system optimises traction and
improves the directional stability of
the vehicle. fi xed, accompanied
by an audiblesignal and a
message on the
instrument panel screen.
Unless it has been deactivated with
the indicator lamp on the button on,
the ESP/ASR system is faulty. Have it checked by a CITROËN
dealer.

Engine
autodiagnosis system fi xed.
The emission control system has a
fault. This lamp should switch off when
the engine is started.
If it does not switch off, contact a
CITROËN dealer urgently.
fl ashing. The engine management system
has a fault. Risk of destruction of the catalytic
convertor.
Have it checked by a CITROËN dealer.

Warning lamp is on Cause Action/Observations

Page 16 of 306

I
34M O N I T O R I N G

Warning lamp is on Cause Action/Observations

Low fuel
level fi xed. When it fi rst comes on there
remains
approximately
5 litres of
fuel in the tank. You must refuel as soon as possible to
avoid running out of fuel.
This warning lamp wil come on every time
the ignition is switched on, until a suffi cient
addition of fuel is made.
Fuel tank capacity: 71 litres.
Never continue to drive until you run out
of fuel, this could damage the emission
control and injection systems.

Maximum
coolant
temperature fi xed red.
The temperature of the
cooling system is too high. Stop as soon as it is safe to do so.
Wait until the engine has cooled down
before topping up the level, if necessary.
If the problem persists, contact a
CITROËN dealer.

Battery
charge fi xed. The battery charging circuit
has a fault (dirty or loose
terminals, slack or cut
alternator belt, ...). This lamp should switch off when the
engine is started.
If it does not switch off, contact a
CITROËN dealer.
+
Seat belt not
fastened/
unfastened fi xed.
The driver and/or the front/
rear passenger has not
fastened or has unfastened
their seat belt. Pull the strap then insert the tongue in the
buckle.

Seat belts
not fastened/ unfastened fi xed, associated
with the seat belt not fastened/unfastened
warning lampl. The illuminated dots represent the not
fastened/unfastened passengers.
They come on:
- fi xed for 30 about seconds on starting the
vehicle,
- fi xed from 0 to 12 mph (0 to 20 km/h) when driving,
-
fl ashing above 12 mph (20 km/h), accompanied
by an audible signal for about 120 seconds.

Page 18 of 306

I
36M O N I T O R I N G
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of the
message "Oil level measurement in-
valid". Consult a CITROËN dealer.

Page 19 of 306

I
36M O N I T O R I N G
Service indicator zero reset
After each service, the service indi-
cator must be reset to zero.
The procedure for resetting to zero
is as follows:

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,

 switch on the ignition; the dis-
tance recorder display begins a
countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of the
message "Oil level measurement in-
valid". Consult a CITROËN dealer.

Page 20 of 306

I
37
M O N I T O R I N G
Engine oil temperature gauge
Under normal operating conditions,
the bars should be within section
1 .
In severe operating conditions, the
bars may extend into section 2 .
In this event, slow down, and if neces-
sary, stop the engine and check the
levels (see corresponding chapter). Coolant temperature
indicator
Under normal operating conditions,
the bars should be within section
1 .
In severe operating conditions, the
bars may extend into section 2 , the
engine coolant temperature warning
lamp A and the STOP warning lamp
will light up, stop immediately .
Switch off the ignition. The cooling
fan may continue to operate for a
certain time .
Consult a CITROËN dealer.
If the SERVICE warning lamp lights
up, check the levels (see correspond-
ing chapter). On horizontal ground, the lighting of
the fuel low warning lamp warns you
that you are at the reserve level.
A message alert is displayed on the
instrument panel.
Fuel gauge indicator

Page 29 of 306

III
46
C O M F O R T
Air conditioning
We recommend use of the automatic
regulation of the air conditioning.
It permits automatic and optimised
control of all of the following func-
tions: air fl ow, temperature in the
passenger compartment and air
distribution, by means of various
sensors (ambient temperature, sun-
shine). This eliminates any need for
you to change your settings other
than the temperature value dis-
played.

 Take care not to cover the sun-
shine sensor A .
If you select the automatic mode (by
pressing the "AUTO" control) and leave
all of the vents open, optimum comfort
will be maintained and humidity and
condensation will be removed regard-
less of the exterior climatic conditions.
The temperature in the passenger
compartment can only be lower than
the ambient temperature if the air
conditioning is on.
HEATING, VENTILATION AND AIR CONDITIONING RECOMMENDATIONS
In order to be effective, the air con-
ditioning must be used with the win-
dows closed. If the vehicle has been
parked in the sun for a long period
and the interior temperature is very
high, fi rst ventilate the passenger
compartment with the windows
open for a few minutes, then close
the windows.
To keep the air conditioning system
in good working order it is essential
that it is operated at least once a
month.
The air conditioning uses engine power
during its operation. As a result, the fuel
consumption of the vehicle increases.
In certain cases of particularly ardu-
ous use (e.g. towing the maximum
load on a steep gradient in high
temperatures), switching off the air
conditioning saves engine power
and improves the towing capacity.
Air inlet
Check that the exterior grille for the
air inlet, at the bottom of the wind-
screen, is clean and free of dead
leaves, snow, etc.
When washing the vehicle using a
high pressure nozzle, avoid spraying
at the air inlet. Air circulation
Maximum comfort is obtained by
means of a good distribution of air in
the passenger compartment, both in
the front and in the rear.
To obtain a uniform distribution of
air, take care not to block the ex-
terior air intake grille located at the
base of the windscreen, the vents,
the air outlets under the front seats
and the air extractor located behind
the fl aps in the boot.
The front and rear vents are fi tted
with thumbwheels to adjust the air
fl ow and direction. We recommend
that you leave all of the vents open.
Dust filter/Odour filter
(active carbon)
There is a fi lter for excluding odours
and dust.
This fi lter must be changed in line
with the vehicle's servicing schedule
(see: "Maintenance and Warranty
Guide").

Page 31 of 306

III
48
C O M F O R T
Control via the manual controls
It is possible to adjust one or more
functions manually, while leaving the
other functions in automatic mode.

 Press one of the controls, with
the exception of that which regu-
lates the temperature 2 . Indicator
lamp A switches off.
Switching to manual mode may
result in discomfort (temperature,
humidity, odour, condensation) and
may not provide optimum comfort.
To return to automatic mode, press
the "AUTO" control.
3. Air distribution adjustment
 Press the controls 3
to change the distri-
bution of the air fl ow. 4. Air conditioning
The air conditioning will only oper-
ate when the engine is running. The
air blower control (air fl ow adjust-
ment) must be active to obtain air
conditioning.
Switching off the ventilation

 Turn control 5 to the
left until the fl ow of
air stops.


Press control 4 . Indicator
light B comes on.
5. Air fl ow adjustment

 Turn control 5 to the
right to increase the
air fl ow or to the left
to reduce it.
6. Front demisting - defrosting
In certain cases, the

"AUTO" mode may not
be suffi cient to demist or
defrost the windows (hu-
midity, several passen-
gers, ice).

 Press control 6 to clear the win-
dows quickly. The indicator lamp
comes on.
The
"OFF" symbol is displayed on
the multifunction screen.
This action switches off the display
and the indicator lamps.
It deactivates all of the system's
functions, with the exception of the
rear screen demisting.
The temperature-related comfort is
no longer controlled (temperature,
humidity, odour, condensation).
Avoid driving for too long with the air
conditioning off.
In order to be effective, the air condi-
tioning must be used with the windows
closed.
Deactivating the air conditioning may
result in discomfort (temperature,
humidity, odour, condensation).
The indicator lamps corresponding
to the distribution chosen come on:
- Windscreen and front side win- dows.
- Front ventilation (central and side vents and air diffusion grille
if open) and rear ventilation.
- Front and rear footwells.
Simultaneous display of the distribu-
tion of air to the windscreen and side
windows and of front and rear venti-
lation is not possible. The air fl ow level is indicated by the
progressive lighting of the blocks of
the bar graph on the control panel
display
9 .
To prevent condensation and dete-
rioration of the quality of the air in
the passenger compartment, ensure
that an adequate fl ow of air is main-
tained.
To reactivate the air conditioning:

 Press control 1 .

Page 32 of 306

III
49
C O M F O R T
It controls the temperature, air fl ow
and intake and distributes the ven-
tilation to the windscreen and front
side windows.
Resuming manual control exits from
"Demisting" mode. It must be can-
celled to permit renewal of the air
in the passenger compartment and
demisting.
Once the screen is clear, press-
ing control 1 returns the system to

"AUTO" mode.

 Press control 7 , with
the engine running,
to demist the rear
screen and the door
mirrors. The indica-
tor lamp comes on.
Demisting is switched off automati-
cally to prevent an excessive con-
sumption of current and in relation
to the ambient temperature.
It may be stopped by pressing con-
trol 7 again or when the engine is
switched off.
7. Rear demisting - defrosting
The heated rear screen operates in-
dependently of the air conditioning
system.
8. Intake of exterior air/
Recirculation of interior air
This function enables you to isolate
the passenger compartment from
exterior fumes and odours. - When starting with the engine
cold, the fl ow will reach its op-
timum level gradually to pre-
vent an excessive distribution
of cold air.
- When entering the vehicle af- ter it has been parked for a
fairly long period, if the inte-
rior temperature is very differ-
ent from your comfort setting
there is no need to change
the temperature displayed
in order to quickly reach the
level of comfort required. The
system automatically uses its
maximum performance to cor-
rect the difference in tempera-
ture as quickly as possible.
- The water resulting from the air conditioning condensation
is discharged via an open-
ing provided for this purpose;
therefore, a puddle of water
may form underneath the ve-
hicle when stationary.
- In all seasons, if the weather is cool, the air conditioning
is useful as it removes the
humidity from the air and the
condensation. Avoid driving
for prolonged periods with the
air conditioning switched off.
However, demisting resumes when
the engine is switched on again.
Switch off the rear screen and door mir-
rors demisting when you consider this
necessary as low current consumption
reduces fuel consumption.

 Press control 8 sev-
eral times to set the
air intake mode, the
indicator lamp comes
on.

It must be cancelled as soon as
possible to permit renewal of the
air in the passenger compartment
and demisting.

Page:   1-10 11-20 21-30 31-40 41-50 ... 80 next >