height Citroen C6 DAG 2007 1.G Owner's Manual

II
1111
A
B
C
EFD
G21
IN BRIEF
FRONT SEATS
C. Adjustment of the backrest angle.
D. Adjustment of the backrest lum-bar support.
E. Seat height and slide adjust-ments.
F. Adjustment of the seat cushion angle.
G. Memorisation of dashboard adjustments:
- Driver's seat.
- Steering wheel.
- Exterior rear view mirrors.
- Head-up display.
You have the possibility to mem-orise two driving positionsusing buttons 1 and 2.
ELECTRICAL ADJUSTMENTS
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
MANUAL STEERING COL-UMN ADJUSTMENT
A. Adjustment of the backrest angle.
B. Controls for the heated seats.
282927
G E T T I N G S T A R T E D

I
12
12
IN BRIEF
While the vehicle is stationary, adjust the height or the reach of the steering wheel by moving the control:forward or rearward to adjust the reach,
up or down to adjust the height.

27
II
S T E E R I N G C O L U M N A D J U S T M E N T – S E A T
B E L T H E I G H T A D J U S T M E N T
MANUAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT AND REACH
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
ELECTRICAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT OR REACH
While the vehicle is stationary, adjust the height or the reach of the steering wheel by moving the control:forward or rearward to adjust the reachup or down to adjust the height.
The steering wheel adjustment is memorised with the driving posi-tion (See “Memorisation”).

28
II
1
3
2
F R O N T S E A T S
ADJUSTMENT OF THE BACKREST ANGLE
Action the control 1 and adjust the angle of the backrest.
It is possible to tilt the backrest 45° forwards until it locks. To unlock it, press control 1.
ADJUSTMENTS TO THE HEIGHT AND ANGLE OF THE HEAD RESTRAINT
To raise it, pull upwards.
To lower it, press on the control 2 to unlock it, and simultaneously on the head restraint itself.
To adjust the angle of the head restraint, tilt it forwards or rearwards at the bottom.
To raise it, press control 2 to unlock it, then pull it upwards.
CONTROLS FOR THE HEATED SEATS
The front seats can be heated independently of each other . On the con-trols for the heated seats 3 located on the outer side of the seats, rotate the knob to select any of three heat intensities:
0: Off.
1: Slight heat.
2: Medium heat.
3: Maximum heat.
Note: The heated seats only operate when the engine is running.
SEAT HEIGHT AND SLIDE ADJUSTMENTS
See following page.

29
II
A
B
C
D
A
BCD
F R O N T S E A T S
Do not drive the vehicle with the head restraints removed; these must be in place, correctly adjusted.
ELECTRICAL ADJUSTMENTS
Adjustment of the backrest angle
To adjust the angle of the backrest, press button A.
Lumbar adjustment
To adjust the backrest lumbar support, press button B.
Seat height and slide adjustments
To slide the seat, press on the horizontal arrows on control C.
To adjust the seat for height, press on the vertical arrows on control C.
Adjustment of the seat cushion angle
To adjust the seat cushion angle, press on control D.
Note: These adustments remain available for a limited time:After you have opened a doorAfter
After you have switched off the ignitionAfter

55
II2
1
43
H E A D - U P D I S P L A Y
The Head-up display projects essential driving data into the driver's fi eld of vision. This enables the driver never to take his eyes off the road.
ACTIVATION/DEACTIVATION
To activate/deactivate the Head-up display: when you switch on the ignition, press on button 1.
The function status (activated/deac-tivated) when you stop the engine is retained when you restart.
ADJUSTMENTS OF THE HEAD-UP DISPLAY
Height adjustment
To adjust the height for the Head-up display, press on buttons 2 and 3.
It is recommended to adjust it as low as possible.
Brightness adjustment
The Head-up display has a bright-ness sensor so that the information can be seen to the best advantage, whatever the ambient brightness.
You can enhance the display brightness at any time by rotating the control 1.
Note:In certain extreme weather con-ditions (rain and/or snow, strong sunlight), the Head-up display may be momentarily subject to interference.
When emerging from a tunnel, there is a certain delay before the system can re-adapt the display brightness to the out-side conditions.
Remark: Certain types of specta-cles may disperse the light coming from the Head-up display.
There is memorisation of driving positions as well as those for the Head-up dis-play
The adjustments you have made for the Head-up display are adopted alongside the driving posi-tion memorisations (see “Memori-sation”): they are:Height adjustment.
Brightness.The types of information selected.

79
II
FEATURES
With dipped beams or main beams, the Directional headlamps function turns the headlamps in the direction the road ahead is taking.
Your vision on bends is considerably enhanced.Note: An automatic correction of the beam height enables you not to dazzle other drivers.
X E N O N D U A L F U N C T I O N D I R E C T I O N A L
H E A D L A M P S
Function activatedFunction deactivated
ACTIVATION/DEACTIVATION
Activated by default, this function can be activated/deactivated in the “Main menu” on the multifunc-tion screen. See “Multifunction dis-play”.
The activated/deactivated status is retained when you switch off the engine.Note: This function is not active when the vehicle is stationary, moving at very low speed, or in reverse gear.
Should there be a malfunction the “Dipped beams” fl ashes. Have the system checked by a CITROËN dealer.
It is recommended to change both Xenon bulbs at the same time if there is a failure of one of them.

93
IIIC
D
R E A R S E A T S
REAR HEAD RESTRAINTS
The rear head restraints have two positions:A stowed position for when the Aseat is not occupied.
A deployed position for safety of Apassengers, locking into place including for a forward-fac-ing child seat.
To lower the head retraints, press on the tab at the base.
To raise them, pull them upwards to their maximum height, pressing the unlocking button.

103
III
G R O U N D C L E A R A N C E A D J U S T M E N T
AUTOMATIC CORRECTION OF GROUND CLEARANCE
Your vehicle has active suspension with variable damping which is electronically controlled. This automatically regu-lates the ground clearance according to the vehicle speed and the road surface conditions.
Limits on access to the posi-tions
Maximum height:
Impossible if speed > 10 km / h (6 mph).
Intermediate position:
Impossible if speed > 40 km / h (24 mph).
Normal road position: Always permitted.
Minimum height:
Impossible if speed > 10 km / h (6 mph).Note: If the speed authorised for a particular position is exceeded, the vehicle reverts automatically to the normal road position.
Signalling of a requested position not authorised
On the display:
The display indicates for a short time, via a message or by hatching on the requested position, that the adjustment is impossible.
The vehicle remains in the position that is authorised and the display confi rms this position.
Automatic variation of ground clearanceIf your speed Ifexceeds110 km / h (68 mph), on a good road, the ground clearance is lowered.
The vehicle reverts to the normal road position if the road deteri-orates or if your speed comes below 90 km/h (56 mph).When the vehicle is stationary the ground clearance is low-ered to the parking position.

157
VI
4
Before positioning the jack, always adjust the vehicle's ground clearance to the “maximum height” position and reta in this adjustment for as long as the jack is under the vehicle (do not use the hydraulic adjustments).
Never get underneath the vehicle if it is supported only by the jack.
The jack and all the tools are designed specifi cally for use on your particular vehicle. Do not use them for any other a pplications.
Have the original wheel repaired and refitted as so on as possible.
It is imperative not to exceed a speed of 80 km / h (50 mph) on the spare wheel.
REMOVAL1. Park the vehicle on stable, fi rm ground that is not slippery. Ap ply the parking brake.2. With the engine idling, adjust the ground clearance to maximum height. See “Comfort” and “Adjusting the ground clearance”. Switch off the igni-tion and engage fi rst gear or reverse gear depending on any slope (for a vehicle with automatic gearbox, select position P).3. Position the chock at the wheel that is diametrically opposite the one to be replaced.4. Position the jack at one of the four jacking-points provided on the sub-frame close to the wheels, then use the handle to unwind the jack until it reaches the ground.5. Slide the removal tool 4 into the notch and lever vigorously to detach the anti-theft bolt protector. See illustration. You can use the handle at the extremity of the tool 4.6. Slacken the wheel bolts.7. Continue to extend the jack until the wheel is a few cen timetres off the ground.8. Undo the bolts, remove the wheel.
C H A N G I N G A W H E E L