Citroen C6 DAG 2009 1.G Owner's Guide

Page 31 of 189

47
II
T R I P C O M P U T E R
Wheel not detected
The SERVICE warning lamp comes on and a vehicle outline is displayed.
The wheel(s) concerned can be identifi ed from the vehicle outline, on which it (they) will be missing. If you have not changed a wheel, such information indicates that the system is malfunctioning.
Contact a CITROËN dealer to have the faulty sensor(s) replaced.
Colour screen CNaviDrive colour display
The defl ation detection system is a driving aid, but which does not absolve the driver from the need to be vigilant and responsible.
This system does not remove the need to check the tyres on a regula r basis (see "Vehicle identifi cation"), to make sure that the vehicle is behaving correctly and to avoid premature tyre wear arising from driving too fast etc.
Do not forget to check the pressure in the spare wheel.
Any repair or replacement of a tyre on a wheel that is equipped with a sensor must be carried out by a CITROËN dealer.Any repair or replacement repair or
The system may suffer from temporary interference caused by radio transmissions on neighbouring frequencies.

Page 32 of 189

48
II
S I G N A L L I N G
DIRECTION INDICATORS
Left, downwards.
Right, upwards.
For a change of direction, move the control stalk beyond the tight spot. Stops automatically with the return of the steering wheel.
Visible alert/headlamp fl ash
Pull the control towards you.
The headlamp fl ash can be made even with the ignition switched off.
Horn
Press at the centre of the steering wheel.
HAZARD WARNING LAMPS
This operates all the direction indi-cators simultaneously.
Only use them to indicate dan-ger, for an emergency stop or for driving in abnormal conditions.
The hazard lamps can also be used with the ignition switched off.
SOUND SIGNAL FOR HEADLAMPS LEFT ON
This operates when the driver's door is opened, ignition off, to indi-cate that the vehicle lamps are still on.
It stops when you close the door, switch off the lamps or switch on the ignition.
This signal does not operate if the automatic lighting of headlamps or the guide-me-home lighting are active.
EMERGENCY OPERATION OF HAZARD WARNING LAMPS
A sudden deceleration of the vehi-cle causes the hazard lamps to come on automatically.
They will cease to operate auto-matically, or manually if you press the hazard lamps button on the dashboard.
The direction indicators cannot operate if the hazard warning lamps are on.

Page 33 of 189

49
II
A
S I G N A L L I N G
GUIDE-ME-HOME LIGHTING
This function switches on your headlamps, to light your way when you wish to walk from a carpark, for example.
This function is activated:Manually by pulling the control A towards you, with the ignition switched off.
Automatically, provided:The automatic lighting of headlamps is activated.To activate the guide-me-home lighting function, select in the "Main menu", then in "Personalisation/Confi guration", the sub-menu for lighting and signalling, then activate the function.
See "Multifunction displays".Note: It is possible to modify the dura-tion of the guide-me-home lighting (approx. 60, 30 or 15 seconds) in the menu "Personalisation/Confi guration".

Page 34 of 189

50
II
C
S I G N A L L I N G
Front foglamps on
Front foglamps and rear foglamps on
Rotate the ring C forwards.
Switching off
First action rearwards, rear foglamps off.
Second action rearwards, front and rear foglamps off.Note: the foglamps should be used only in fog or in other conditions of poor visibility.
FRONT AND REAR FOGLAMPS (RING C)
Lighting
With dipped/main beams on:
Rotate the ring C forwards.
DAYTIME-RUNNING LAMPS
These come on automatically when the engine is running:If the function is activated in the Main Menu. See "Multifunction displays".
Provided the lighting control stalk is on position 0 and all the headlamps are off.
If the daytime-running lamps are active, the sidelamps will also be on (depending on country specifi -cation).

Page 35 of 189

51
II
FEATURES
With dipped beams or main beams, the Directional headlamps function turns the headlamps in the direction the road ahead is taking.
Your vision on bends is considerably enhanced.Note: An automatic correction of the beam height enables you not to dazzle other drivers.
X E N O N D U A L F U N C T I O N D I R E C T I O N A L
H E A D L A M P S
Function activatedFunction deactivated
ACTIVATION/DEACTIVATION
Activated by default, this function can be activated/deactivated in the "Main menu" on the multifunc-tion screen. See "Multifunction dis-plays".
The activated/deactivated status is retained when you switch off the engine.Note: This function is not active when the vehicle is stationary, moving at very low speed, or in reverse gear.
Should there be a malfunction the "Dipped beams" warning lamp fl ashes. Have the system checked by a CITROËN dealer.Should there be a malfunction the "Dipped beams" warning lamp fl ashes. Have the system checked Should there be a malfunction the "Dipped beams" warning lamp fl ashes. Have the system checked
It is recommended to change both Xenon bulbs at the same time if there is a failure of one of them.

Page 36 of 189

52
II
W I P E R S
CONTROL POSITIONS2: Rapid wipe.
1: Normal wipe.
I: Intermittent wipe.0: Off.
One press downwards:AUTO: Automatic wipe activated.Single wipe.

Page 37 of 189

53
II
CHANGING THE WIPER BLADES
If you have to replace them, the wiper blades have to be parked in the maintenance position. For this, switch off the ignition and then within one minute move the wiper control stalk. The wipers stand up in a vertical position.
After replacement, switch on the ignition and move the wiper control stalk so that the wipers resume their normal position.Note: this action places the Piloted Defl ector in the maintenance position.
WINDSCREEN WASH
To operate the windscreen wash, pull the wiper stalk towards you.
The screen wash is accompanied by a timed wipe of the windscreen , the headlamp wash also activates if the dipped beams are on.
The display of a message indicates that there is only approx. one litre of screen wash fl uid remaining.
In freezing conditions, always check that the wiper blades are free to operate.
Remove any accumulation of snow at the base of the windscreen.

Page 38 of 189

54
II
A
W I N D O W S
After a battery disconnection or if there has been a malfunction, you have to reinitialise the anti-pinch function for each window:Lower the window fully using the control, then close. It will rise only a few centimetres. Press repeatedly on the control until the window is fully closed.
Keep the control pressed for at least a few seconds after the window has fully closed.
WARNING
During this operation, the anti-pinch protection does not work.

Page 39 of 189

55
II
S T E E R I N G C O L U M N A D J U S T M E N T –
S E A T B E L T H E I G H T A D J U S T M E N T
MANUAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT AND REACH
While the vehicle is stationary, unlock the steering wheel by push-ing the lever forward.
Adjust the height and the reach of the steering wheel, then lock the position by pulling the lever upwards.
ELECTRICAL ADJUSTMENT OF THE STEERING WHEEL FOR HEIGHT OR REACH
While the vehicle is stationary, adjust the height or the reach of the steering wheel by moving the control:forward or rearward to adjust the reachup or down to adjust the height.
The steering wheel adjustment is memorised with the driving posi-tion (See "Memorisation").

Page 40 of 189

56
II
1
3
2
F R O N T S E A T S
ADJUSTMENT OF THE BACKREST ANGLE
Action the control 1 and adjust the angle of the backrest.
It is possible to tilt the backrest 45° forwards until it locks. To unlock it, press control 1.
ADJUSTMENTS TO THE HEIGHT AND ANGLE OF THE HEAD RESTRAINT
To raise it, pull upwards.
To lower it, press on the control 2 to unlock it, and simultaneously on the head restraint itself.
To adjust the angle of the head restraint, tilt it forwards or rearwards at the bottom.
To raise it, press control 2 to unlock it, then pull it upwards.
CONTROLS FOR THE HEATED SEATS
The front seats can be heated independently of each other. On the controls for the heated seats 3 located on the outer side of the seats, rotate the knob to select any of three heat intensities:
0: Off.
1: Slight heat.
2: Medium heat.
3: Maximum heat.
Note: The heated seats only operate when the engine is running.
SEAT HEIGHT AND SLIDE ADJUSTMENTS
See following page.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80 ... 190 next >