headlamp Citroen C8 2008.5 1.G Owner's Manual

Page 5 of 250

Interior
10

5. Control block.

6. Steering wheel audio equipment
controls.

7. Wipers/wash-wipe/trip computer
controls.

8. Gear lever.

9. Ignition.

1. Interior protection alarm
deactivation button.

2. Speed limiter/cruise control
switches.

3. Lights and direction indicators
controls.

4. Driver’s air bag.
Horn.
10. Headlamp height adjustment.

11. a - Dynamic stability control button
(ESP/ASR).
b - Parking assistance button.

12. Steering wheel adjustment control.
INSTRUMENTS AND CONTROLS

Page 9 of 250

53
3
3
Interior
14
173 48
Repositioning
SIT COMFORTABLY
SEE CLEARLY
Adjust the height
and depth of the
steering wheel.
Electric exterior mirrors.
Selection Seat belts
Height adjustment.
Fastening. Lights off
Side lights
Main beam headlamps (blue)
Dipped headlamps (green)
Wipers stalk 45

2 fast.
1 normal.
I intermittent.
0 off.

 single wipe.

AUTO, press the stalk down.

AUTO, automatic switching
on of the lights
Adjustment
86

Page 29 of 250

Instruments and controls
READY TO SET OFF
2
33
Warning light is indicates Solution - action
ESP/ASR fl ashing.
wheel skid avoided. The system optimises the traction and improves
the directional stability of the vehicle.
Chapter 5, "Driving safety" section.
remaining on.
a malfunction of the system.
E.g.: under-infl ation of the tyres. Check the pressure of the tyres. Call a CITROËN
dealer .
remaining on
with the button
(below the
steering wheel
on the left)
pressed. deactivation of the system.
The operation of the system has been
deactivated.
Chapter 5, "Driving safety" section.

Diesel
pre-heating lit. climatic conditions requiring
pre-heating. Wait until the warning light is switched off before
operating the starter.

Dipped
headlamps/
Daytime
lights lit. manual selection or
automatic lighting.
Rotate the ring on the lights stalk to the second
position.
lighting of the dipped headlamps
from the time the ignition is switched
on - daytime lights. Depending on the
country in which the vehicle is sold.
Chapter 3, "Steering wheel controls" section.

Main beam
headlamps
pulling of the stalk towards
you. Pull the stalk to return to dipped headlamps.
and with an
audible signal,
ignition off. opening of the driver’s door
with the lights still on.
Rotate the ring on the lights stalk to position 0.

Direction
indicators fl ashing with
buzzer. change of direction via the
lights stalk, to the left of the
steering wheel. To the Right: control to be pushed upwards.
To the Left: control to be pushed downwards.

Page 30 of 250

Instruments and controls
34
Warning light is indicates Solution - action
Front fog
lamps lit. manual selection. The fog lamps only operate if the side lights or
dipped headlamps are on.

Rear fog
lamps lit. manual selection. The fog lamps only operate if the side lights or
dipped headlamps are on. In conditions of normal
visibility, take care to switch them off on penalty of
being booked. "This light is a dazzling red."
Display is indicates Solution - action
Cruise control lit. cruise control selected. Manual selection. Chapter 3, "Steering wheel
controls" section.

Speed limiter lit. speed limiter selected. Manual selection. Chapter 3, "Steering wheel
controls" section.

Service
spanner lit. service due shortly. Refer to the list of checks in the servicing booklet.
Have the service carried out by a CITROËN
dealer .

Automatic
gearbox displayed. gear lever position selected. Chapter 2, "Instrume
nts and controls" section.

Particle
emission fi lter
saturation
warning displayed and
associated with
the service
warning light. malfunction of the particle
emission fi lter (diesel
additive level, risk of
clogging, ...).
Have the fi lter checked by a CITROËN dealer .
Chapter 7, "Levels" section.

Page 43 of 250

Steering wheel controls
ERGONOMICS and COMFORT
3
47
Automatic "Follow-Me-Home"
lighting

With the ignition off, when you leave your vehicle with the automatic switching on of the lights function activated , the side lights and dipped headlamps remain on for the selected duration.
To deactivate or activate this function, go to the display confi guration menu .

The duration of the timed period must also be set (15, 30, 60 seconds), via the display confi guration menu.
Carry out these operations when the vehicle is stationary. HEADLAMPS BEAM

Depending on the load in your vehicle, the beam setting must be adjusted.
0- 1 or 2 people in the front seats.
1- 5 people.
2- 6 to 8 people.
3- Driver + maximum authorised loads.
Initial setting is position 0.

In foggy weather or in snow,
the brightness sensor can
detect suffi cient light. As a
consequence, the lights will not come
on automatically.
Automatic switching on of the lights Deactivation
Turn the ring forwards or rearwards.
The deactivation of this function is
accompanied by a message on
the display.
The function is deactivated temporarily
when you use the manual lights stalk.

If the brightness sensor does not
function correctly, the lights come on
accompanied by the service warning
light, an audible signal and a message
on the display.
Contact a CITROËN dealer .
Do not cover the brightness
sensor located in the centre of the
fascia. It is used for the automatic
switching on of the lights and for the
automatic wipers.
Activation
Turn the ring to the AUTO position.
The activation of this function is
accompanied by a message on the
display. AUTOMATIC ADJUSTMENT OF
THE XENON HEADLAMPS
headlamps, this system automatically corrects the height of the light beam, regardless of the load in the vehicle. The driver is then guaranteed optimum lighting without dazzling other road users.

Cancelling:

 "fl ash" the headlamps,
 get out of the vehicle and lock it.
If your vehicle is fi tted
with a brightness
sensor, the side lights
and dipped beam
headlamps switch on
automatically if the
light is poor, or during operation of the
windscreen wipers. They switch off
as soon as the light becomes bright
enough or the windscreen wipers stop.
This function is not compatible with the
daytime lights.

Page 44 of 250

48
WINDSCREEN WIPER STALK
Manual windscreen wipers Special position of the
windscreen wipers

In the minute following switching off of the ignition, any action on the stalk positions the wipers against the windscreen uprights.
This action enables you to position the wiper blades for winter parking, cleaning or replacement. Vehicle fitted with the
automatic windscreen
wipers control

Do not cover the rain sensor located in the centre of the fascia.
On vehicles which are fi tted with this control, in the AUTO position, the windscreen wipers operate automatically and adapt their speed to the intensity of the rainfall .
When not in AUTO mode, for the other positions, refer to the manual windscreen wipers section.
The command must be reactivated whenever the ignition has been switched off for more than one minute:
 move the stalk to any position,
 then move it back to the required position.

2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
l Intermittent wipe.
0 Off.
 Single wipe
(press downwards).
Refer to the "Changing a windscreen wiper blade" section of chapter 8.
Wash-wipe and headlamp wash

Pull the stalk towards you, the wash-wipe is accompanied by a timed sweep of the wipers.
If your vehicle is fi tted with this function, the headlamp wash is linked with the wash-wipe, it is triggered if the dipped headlamps are on.

To park the wipers in their normal position after this has been done, switch on the ignition and move the stalk.

To top up the levels, refer to the "Levels" section of chapter 7.

In the I ntermittent position, the wiping speed is in proportion to the vehicle speed.

Page 184 of 250

186
Towing a trailer
On the contrary, use a high gear to
lower the engine speed and reduce
your speed.
In all cases, pay attention to the
coolant temperature.
Brakes: towing increases the braking
distance. Drive at a moderate speed,
change down early and brake
gradually. Please contact a CITROËN dealer fi rst
for further information.
Automatic adjustment
For vehicles with Xenon bulbs, and if
the change in load makes it necessary,
this system automatically corrects the
height of the beam after approximately
2 minutes. The driver is then assured
of having optimum lighting and not
causing a nuisance to other road
users.

In certain cases of particularly
arduous use (towing the
maximum load up a steep slope
in high temperatures), the engine
automatically limits its power.
In this case, cutting off the air
conditioning allows the engine power
to be recovered, and therefore the
towing speed to be signifi cantly
increased (approximately 12 mph
[20 km/h] more). Sequential control
of the gearbox may also become
unavailable. Lighting
Bicycle carrier If you fi t a bicycle carrier on
the tailgate, deactivate the
rear wiper from the display’s
confi guration menu.
Refer to the "Identifi cation
features" section of chapter 9. Refer to the "Steering wheel
controls" section of chapter 3.
When using a trailer connection,
you must add a fuse. Refer to
the "Changing a fuse" section of
chapter 8.

If the coolant temperature warning light
comes on, stop the vehicle and switch
off the engine as soon as possible.

Tyres: check the tyre pressures of
the towing vehicle and of the trailer,
observing the recommended pressure.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed.

Towbar
We recommend the use of original
CITROËN towbars, which have been
tested for endurance from the design
stage of your vehicle.
Towing equipment must be fi tted in
accordance with the manufacturer’s
instructions, with particular attention to
the towing capacities of your vehicle,
the load towed, the nose weight and
the electrical connection. As this fi tting
should be carried out by a professional,
we recommend that you entrust the
fi tting of this equipment to a CITROËN
dealer .
In accordance with the general
instructions referred to above, we draw
your attention to the risk connected
with fi tting a towbar or other electrical
accessory which is not recommended
by the CITROËN network . Fitting such
equipment could result in a failure of
your vehicle’s electronic system. Manual adjustment
Adjust your headlamps so as not to
dazzle other road users. Check the
electrical signalling of the trailer.

Page 193 of 250

197
Levels
CHECKS
Cooling system
Only use the fl uid recommended by the
manufacturer.
Otherwise, you risk seriously damaging
your engine.
When the engine is warm, the
temperature of the coolant is controlled
by the engine fan. As this fan can
operate with the ignition key removed
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by 1/4 of a turn to
release the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and top
up the level with coolant.
If fl uid has to be added frequently,
this indicates a failure which must be
checked by a CITROËN dealer as
soon as possible. Power steering fluid level
The vehicle must be parked on level
ground with the engine cold. Unscrew
the cap integrated with the gauge and
check the level which must be between
the MIN and MAX marks.
During regeneration of the particle
emission fi lter, relay noise may be
heard under the fascia.
If the message is still displayed and
the service warning light remains on,
contact a CITROËN dealer .
Diesel additive level (Diesel with
particle emission filter)
When this occurs with the engine
running, this is due to the start of
saturation of the particle emission fi lter
(exceptionally prolonged urban driving
conditions: low speed, long traffi c
jams, ...).
In order to regenerate the fi lter, you
are advised to drive at a speed of
more than 40 mph (60 km/h) as soon
as possible, when traffi c conditions
permit, for at least fi ve minutes (until
the message disappears and the
service warning light is switched off).
Topping up
The level must be between the MIN
and MAX marks on the expansion
bottle. If more than 1 litre of fl uid is
required to top up the level, have the
system checked by a CITROËN dealer . Windscreen wash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products of the CITROËN range.
To avoid ice forming, do not use water.
Topping up
It is imperative that this additive is
topped up by a CITROËN dealer
without delay.
Used oil
Avoid prolonged contact of used oil
with the skin.
Brake fl uid is harmful to health and
very corrosive.
Do not dispose of used oil, brake
fl uid or coolant into drains or onto
the ground but into the containers
dedicated to this use at CITROËN
dealerships .
The minimum level of this
additive is indicated by
lighting of the service warning
light, accompanied by an
audible signal and a message
on the display.

Page 200 of 250

204
Changing a bulb
CHANGING A BULB
Handle the bulbs with a dry cloth.
Make access easier on the right-
hand side by removing the wash-wipe
pipe and the fuse box cover.
High pressure washing: when using
this type of washing on stubborn dirt,
do not persist on the headlamps, the
lights and their surrounds to avoid
damaging their coating and their seal. 2 - Main beam headlamps
H7 - 55 W or xenon bulb.
- Turn the protective cover corresponding to the faulty bulb
a quarter of a turn to the left and
remove it.
- Disconnect the connector.
- Press the end of the securing clip to free it.
Change the bulb.
When fi tting the new bulb, ensure that
the direction notches are positioned
correctly and the securing clip is fi xed
properly.
- Reconnect the connector.
- Refi t the protective cover, then turn it a quarter of a turn to the right.
3 - Fog lamps
H1 - 55 W 3 W.
FRONT LIGHTS

1. Dipped headlamps

2. Main beam headlamps

3. Fog lamps

4. Side lights

5. Direction indicators 1 - Dipped beam headlamps
H7 - 55 W or xenon bulb. 4 - Side lights
W 5 W.
- Turn the bulb holder a quarter of a turn to the left and remove it.
- Change the bulb.

WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be changed by a
CITROËN dealer .

Page 201 of 250

205
TROUBLESHOOTING
8
Changing a bulb
Rear lights

1. Direction indicators
PY 21 W (amber).

2. Side lights
P21 W.

3. Brake/side lights
P21/5 W.

4. Reversing lights
P21 W.

5. Fog lamps
P21 W.
5 - Direction indicators
PY 21 W (amber).
- Turn the bulb holder a quarter of a turn to the left and remove it.
- Change the bulb.
The headlamps are fi tted with
polycarbonate glass with a
protective coating. Do not clean
them with a dry or abrasive cloth, nor
with a detergent or solvent product.
Use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity), condensation
inside the headlamp glass is normal;
it disappears a few minutes after the
lights are switched on. Direction indicator side repeaters
WY 5 W (amber).
- Push the repeater rearwards and
release it from the mirror.
- Hold the connector and turn the bulb holder a quarter of a turn to
the left.
- Turn the bulb a quarter of a turn to the left, remove it and change it.
When refi tting, engage the repeater
towards the rear and move it towards
the front of the mirror.
Amber coloured bulbs (direction
indicators and side repeaters)
must be changed for bulbs of
identical specifi cation and colour. These 5 bulbs are changed from inside
the vehicle:
- open the tailgate,
- remove the air extraction grille on
the side concerned,

Page:   1-10 11-20 next >