engine Citroen CX 1977 1.G Service Manual

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 01 : 1’. I, -1’ IO c ( lOi, o/ I/J<, c~lcrlricnl /l/lilS. Op. MA. 01 1 PROTECTION OF THE ELECTRICAL UNITS
PRECAUTIONS WHEN CARRYING OUT WORK ON THE CAR
1. Battery :
a) Disconnect the negative terminal first, then the positive one.
b) Ensure the battery is properly connected, with the negative terminal being connected
to earth.
c) Carefully connect both leads to the battery terminals, the negative lead being connected
last.
Before connecting the negative lead ensure that there is no flow of current. This can
be established by briefly touching the negative terminal pith the lead end : sparks
indicate a short circuit which must be corrected first.
d) Before using the starter ensure that the two leads are correctly tightened on their
respective terminals. $ 2. Alt ernator-Regulator :
a) Do not rotate the alternator unless it is connected to the battery.
0
2
2 b) Before connecting the alternator ensure that the battery is correctly connected
2 (negative terminal to earth ).
c) Do not check the operation of the alternator by short-circuiting either the positive or
the u EXC )) terminals and the earth terminal.
d) Take care not to reverse the leads connected to the regulator.
e) Do not attempt to re-energize the alternator : this is never necessary and in any case
would damage both the alternator and the regulator.
f ) Do not connect a suppressor capacitor at the u EXC )) terminal of the alternator or the
regulator.
g) Do not connect a charging unit to the battery and never carry out arc welding ( or spot
welding) on the car chassis unless both the positive and the negative leads are
disconnected from the battery. 3. Ignition coil :
4. Q.I. Headlamps :
a) Connect the supply lead of the coil to the external ballast resistor terminal and not to
the coil itself.
b) Connect the suppressor with a jump lead to the feed terminal of the coil. Only fit the
suppressor recommended by the factory.
a) Only replace a Q.I. bulb with the headlamps switched off. After having used the head-
lamps, it is wise to let them cool down for five minutes before handling.
b) Do not touch a Q.I. bulb with bare fingers. Any fingerprints on the bulb must be cleaned
off with soapy water and the bulb dried with a lint-free cloth.

Downloaded from www.Manualslib.com manuals search engine 1. HYDRAULIC FLUID :
\~ir/~rol 6jr/rol,/ir j111icl ( LHM ) is the only suitable type and must be used to the exclusion of all others in the
hydraulic system of the car.
This LHM fluid is gt~‘~,l
iv c-o/or/~ and similar to engine oil.
The use of nr!~’ oih~~- rc,otll$
twirl the rubber rinqs and seals in the system 2. RUBBER UNITS AND PARTS :
Suitable components are identified by their grcc’r/ colo/~r and may only be replaced by gc~rttri~ro wplor-c~t~~c~nf
col,,pollc,l/fs painted or marked in green.
All rubber components (joints, hoses, diaphragms, etc . . . ) are of a
spvcirfl qtrnlif), ior ~/.SCJ wifh idlfM (Iuid and are
identified by their white or green colour, 3. STORAGE :
ix Components must be stosed /11i1 o/ /Irlirl nr~tl blor~k~rl o!j: Like the piping they must be protected against shock
E and the inqress of dust
7 Rubber tubing and joints must be stored away from dust. air, light and heat.
al
co
0 LHM hydraulic fluid must be stored in its original containers carefully sealed We advise the use of litre ( for
: toppinq up ) or five litre containers ( for refillinq ) to avoid havinq to keep opened containers.
2
2 T-, 4. CHECKS BEFORE CARRYING OUT WORK :
Z +
c
E Before working on the hydraulic system in case of incorrect operation, ensure the following :
a
a a) T/FOI the c-r>ufrol.y or f/l<, rnc~ch~uir~~l livkrrgc~s o/ //I(’ uuits or f/lo gmltp o/ h\~d~c~u/i~ ~~~~it.s in(nln>d are HO/
lt?
sfi]/ it) o/~c,rnfiou.
b) and that the 111’ c-ire-/ii/ is ////(/(jr /~I.(Jss/II.(J. as follows :
With the engine at idling speed :
- Unscrew the pressure-release screw on the pressure requlator by one or one and one half turns : a sound
, of leakage should be heard from the requlator.
= Retighten the release screw : cut-out must occur which results in a reduction in the running noise
emitted by the H P pump.
If not check in the following sequence
- that there is sufficient fluid in the reservoir,
- that the reservoir filter is clean and in good condition,
= that the H.P pump is primed and there is no air leak on the suction side of the pump,
- that the release screw of the pressure requlator is correctly tightened

Downloaded from www.Manualslib.com manuals search engine 2
OPERATION No MA. 02 : I!‘orki//g OI/ hyc/rt/t/lic s\,s/vN/.
5. PRECAUTIONS TO BE TAKEN BEFORE WORKING ON THE HYDRAULIC SYSTEM :
a) (.~rvJuI/)~ CIVOII the area of work, the unions and the unit to be removed
Disconnect the lead from the negative terminal of the battery
Only use petrol or lead-free petrol for cleaning.
b ) I~~J/VNSO
the /)twsure in the circuits
- Place the vehicle in the G /arc B
position. stop the engine.
- Slacken the Pressure Requlator release screw.
Wait until the front of the car has reached the low position 6, PRECAUTIONS TO BE TAKEN DURING REMOVAL :
a) t3lnuk o!! the w~~tnl pi/~es with plugs, and rubber tubes with round pins of the correct diameter
b)
t3lmk of/ //IV op,c,/li,lg.s of components with pluqs of the correct diameter
NOTE : Plugs and pins must be carefully cleaned before insertion. 7.. CHECK OR TEST OF HYDRAULIC UNITS :
- Use 3654-T t~sf hc~~c-h equipped and designed for use with LHM fluid
This bench is /)ciitltc’d ~IY’~‘~/ and its accessories are marked in green.
- Never use the bench with another fluid or for testing components operating with another fluid (units of a (( D ))
car using LHS2 for instance ).
NOTE The (< Le Bozec )) pump used on test benches for checking DIESEL injectors can be resorted to for
testing components operating with LHM mineral fluid provided that the bench is cleaned first. 8. PRECAUTIONS TO BE TAKEN DURING REFITTING :
E steel pipes must be blown through with compressed air,
5 rubber tubes and joints must be washed in petrol or white spirit and then dried with compressed air,
= hydraulic units must also be cleaned with petrol or white spirit and blown through with compressed air.
NOTE Renew all joints and seals during refittinq .
b
) 12rlbrijicntim :
- Follow the indications as stated in the operations in the Manual..
- Joints and internal parts must be liqhtly oiled hefore fitting ( use mineral fluid LHM only )
L If parts in contact with hydraulic units have to be qreased use a mineral grease only ( as employed for
Cardan shafts or bearings ).

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 02 : I+ 4’ 0, “‘g 01, Ill<, l1\~c!).ollli(- s\‘sfell~. Op. MA. 02
I To connect a union proceed as follows :
- Position sleeve-seal (( a u lightly coated with
L,HM fluid; this sleeve seal must not reach the
extremity of pipe (( b )).
- Centre the pipe in the housinq by lininq it up
with the axis of the hole, avoidinq all stress.
( Ensure that the end u b )I of the pipe enters
into the smali bore C< c )> j.
Start screwing in the union nut by hand.
- Tiqhten nut moderately : excessive force could
cause a leak because of deformation of the pipe
NOTE Tiqhteninq torques :
3.5 -mm pipe t 5.8 to 6 6 ft lbs
4 5 mm pipe 5 8 to 0 mN ( 0.8 to.0 9 ‘1 kg )
6 6 to 8 0 ft.lbs
6. O-mm pipe
1
9 to 11 mN (0 9 to 1 1 m.kg ) c ) Fittilzg :
I Only use joints of a quality compatible with LHM mineral fluid.
The design of the various seals ensures that their sealing action increases with fluid pressure The oiltiqhtness e
is therefore not improved by greater tiqhtness of the unions
2 To connect a rubber tube a rubber rinq of suitabie diameter has to be positioned between thr, tube and the hose
:
E clip.
0
x
a
A 9, CHECKS ON COMPLETION OF WORK
On completion of work on hydraulic units or the system itself check the followinq :
h) ‘1’11~ C./CJ~~~IIC-C, I~c,lrt,c,c,rt I/J<
pipvs : pipes must not touch one another or any other component, nor may any other
unit, whether fixed or movable, exert any stress on them.

Downloaded from www.Manualslib.com manuals search engine 4 II - REPAIRS PLASTIC TUBING.
OBSERVATIONS :
a) This operation can be sarried out by sleeving the damaged tube
b) If two sleeves are to be located on one length of tube the interval between them must be about 30 in in order
to retain the flexibility of the tubing.
c) Obtain a bottle of Rilsan adhesive ( 125 cc ) sold by the BOYRIVEN firm , 37 bis rue de Villiers _
92200 u NEUILLY sur SEINE - Tel. 624-36-11
( Rilsan adhesive harms the skin : avoid touching it with the fingers, use a wooden spatula instead
1. Cut the tubing and roughen the ends over a lenqth of some 3.5 in. with abrasive paper N” 600
2. Carefully deqrease the roughened ends and the sleeve with trichlorethylene
3. Heat the Rilsan adhesive in a water-bath to raise its temperature to 60°C.
Do root c~sc-c~c~d /his Icv~p~~rntriw.
NOTE : This operation is essential to cut down drying time
4, Coat the ends of the tube and the inside of the sleeve with adhesive.
Leave the parts to dry for a few minutes.
Insert the ends of the tube into the sleeve.
).
Allow the assembly to dry for three to four hours before using the repaired tube aqain.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 03 : ~e~ommwd~d ntaterials. Op. MA. 03
BASE
‘ainted
metal
‘ainted
metal
rrdboard
Felt
Glass
olyester MATERIAL TO
BE BONDED
Targa
Rubber
Finishing strip
Vinyl
Cloth
Felt
Aluminium
( Lower edge
of windows )
Base of mirror
stems
Rilsan
(runners )
Klegecel
Polyurethane
foam MAIN RECOMMENDED MATERIALS
I. ADHESIVES. METHOD OF
APPLICATION
Coating of the base
Coating of the material
Drying
Positioning
Smoothing
Coating of the base
Coating of the material
Drying
Positioning
Smoothing
Coating of the base
Drying
Positioning
Smoothing
Preparation of adhesive
Preparation of surfaces
Coating of both faces
Application of pressure
Bonding time
Preparation of surfaces
Coating of material
Positioning
Application of pressure
Coating of base
Coating of material
Drying
Positioning
Application of pressure
Coating of base
Coating of material
Drying ( 3-8 mins )
Positioning
Application of pressure
Coating of the base
Drying
Positioning
Smoothing TYPE OF ADHESJVE
( Examples )
REST-AGRAF
Neoprene
Ref. Choisyprene
TEROSON
Ref. Terokal 2444
MINNESOTA
synthetic rubber adhesive
Ref. : EC 1236
MIPLACOL
Acrylo-nitrite Ref. : HS 3688
S.E.R.
ONFROY
Ref. : 306
BOSTIK
Natural rubber adhesive
Ref. : 1313
TEROSON
EPOXY
Ref. : Terokal
COLFIX
Ref. : Mastic01
COMET
Special
Ref. : Glass/metal kit
COLFIX
Neoprene
Ref. : 550
MINNESOTA
Ref. : EC 1099
BOSTIK
Neoprene
Ref. : 1400
MINNESOTA
Ref. : EC 1099
COLFIX
Neoprene
Ref. : 180
MINNESOTA
Ref. : Spray Pavillon 77 RECOMMEND
SOLVENTS
Petrol
Trichlorethane 11’
Trichlorethane 11
Petrol
Warm water before
polymerisation
Super-clean
Petrol
Trichlorethane 11.
Trichlorethane 11
Solvent S
(P.C.A.S. )
Petrol
Trichlorethane

Downloaded from www.Manualslib.com manuals search engine 2 OPERATION No MA. 03 : I~grhdicwts prdcomis&.
II. CLEANSING PRODUCTS
-
USAGE PRODUCT
R insing LHM hydraulic
Pi
ping
D egreasing of mechanical
a: ssemblies, when cold
oint face cleanser
‘leaning of carburettors CHARACTERISTICS
I MANUFACTURERS.
I
TOTAL
Hydro-rincage
MAGNET 6
OIL AND GREASE
REMOVER
PROTOLAN 3 D
RAVITOL X
MAGSTRIP
SUPER-CLEAN
Carburettor cleaner
P.D.R.
Carbuclin For a thorough rinse, leave the
product in the circuit for 1000 km
(600m) TOTAL
C.F.R.
Insoluble, in water, dries rapidly
has high insulating qualities MAGNUS
Let the product act
(undiluted in solvent ) then
rinse with water MULLERANDCO
Is used undiluted and must be
rinsed with water
Gelatineous liquid for removing
liquid gaskets and non-metal
gaskets Ets N BREGER
Ets RAVICOLOR
MAGNUS
Dry cleanser to be used before
application of Loctite products COMET
Department D.A.V.A. /
III. SEALING PASTES.
PRODUCT
PROTO-JOINT
CURTYLON
LOWAC
FRENETANCH
FRENEBLOC
FORMAJOINT
SILICOMET
noir
(blark ) CHARACTERISTICS
Resist mechanical stress, and
oil-derived products MANUFACTURERS USAGE
JEAN - BRASSART
CEFILAC
Department Joint Curty Clean with alcohol -
Resists hydrocarbons
SEBIS
Locks and seals any assembly
which is screwed on, but must
remain removable Sealing of joint faces,
screws, studs and nuts
Locks and seals studs, screws
and nuts with maximum
effectiveness COMET
Department D.A.V.A.
NOTE : These five
products are available as
a kit, with in addition
SCELBLOC (to be used
when securing bearings,
bushes etc.. ) and SUPER-
CLEAN (cleansing pro-
duct ) Seals joint faces and unions
Seals joint faces, as replacement
of ordinary gaskets
Sealing of door and wind-
screen sealing rubbers

Downloaded from www.Manualslib.com manuals search engine Op. MA. 03 3
SEALING PASTES (continued)
USAGE
Sealing of porous
sections of casings
Sealing of the pipes
warning the inlet
manifold PRODUCT CHARACTERISTICS MANUFACTURERS
COMET
DEVCON F
Department D.A.V.A.
Aluminium based
METALIT DISEMPEX
METOLUX A Light metal based
METOLUX
SILASTIC 732 R.T.V. Remains supple after drying DOW CORNING S.A.R.L.
Refractory adhesive
paste Ref. 1500 Ets BARTHELEMY
(COLLAFEU ) . IV. PENETRATING OILS.
2 6 , USAGE PRODUCT CHARACTERISTICS MANUFACTURERS
7
a,
Rusty or corroded DEGRIPPANT Aerosol MOLYDAL
‘-
-6 components, or assemblies
: DEGRIPPANT MO Aerosol or 5 litre can SOFRALUS-BARDAHL
2- rusted in position V. GREASES AND LUBRICANTS.
USAGE PRODUCT CHARACTERISTICS MANUFACTURERS
RHONE-POULENC
Greasing of (< fluid-bloc )) S.I. 33 LAMBERT-RIVIERE
suspension bushes Silicone grease
GRAISSE 33
(MEDIUM ) DOW CORNING S.A.R.L.
GRAISSE 1495 Highly adhesive universal
MOLYDAL
grease
Greasing of drive-shafts MOLYKOTE
LONGTERM 2 Extreme pressure grease, good
DOW CORNING S.A.R.L.
adhesive, and is waterproof
TOTAL MULTIS MS Universal grease TOTAL C.F.R.
Lubricant for rubber and
plastic REDEX-SILICONE Aerosol REDEX - FRANCE
Aerosol lubricant; resists salt
Components operating
HI _ LUB - HTC
under difficult conditions and fresh water at high pressures COMET
and temperatures (Department D.A.V.A. )
Lubricant for spark-plug
threads NO-BIND Anti-locking lubricant ; resists
high temperatures CEFILAC
(Department Joint Curty )

Downloaded from www.Manualslib.com manuals search engine 4
OPERATION No MA. 03 : K C’C c ,I,,, ~,~‘,r’dVd nln/c~rinls
NAME
AGIR
BARTHELEMY
BOSTIK S.A.
BRASSART J
ETN BREGER
CEFILAC
( Department joint Curty )
C.F.R. ( TOTAL )
COMET
(Department D.A.V.A. 1
COLFIX ( SCHULTZ )
DISIMPEX
DOW-CORNING S.A.R.L.
LAMBERT-RIVIERE
MAGNUS
METOLUX S.A. FRANCE
(Societe Henri Lecocq 1
MINNESOTA DE FRANCE
MIPLACOL
MOLYDAL
MULLER & Cie
ONFROY
P.C.A.S.
RAVICOLOR
REDEX--FRANCE
REST-AGRAF
S.E.B.I.S.
SOFRALUS-BARDAHL
TEROSON LIST dF MANUFACTURERS
ADDRESS
6936G SEREZIN du RHDNE .......
61, rue Defiance 943G0 VINCENNES ...........................................
5, route de St Leu 95360 MONTMAGNY ......................................
44, rue de la Boetie 75008 PARIS ...............................................
Le Pasty St Aubin de Luigne 49190 ROCHEFORT LOIRE .......
25, rue Aristide Briand 69800 SAINT PRIEST ..........................
or 7 a 11, rue de la Py 75020 PARIS ..........................................
11, rue du Docteur Lancereaux 75381 PARIS CEDEX 08 .......
10, rue Eugene Cazeau 60300 Z.I. de SENLIS ...........................
43, route de la Metzeau 68100 MULHOUSE ................................
1, rue Goethe 75016 PARIS ...........................................................
140, avenue Paul Doumer 92500 RUEIL MALMAISON ..............
16, rue de Miromesnil 75008 PARIS .............................................
12, rue du Moulin de Cage 92390 VILLENEUVE LA GARENNE
167, rue de Fontenay 94300 VINCENNES ...................................
135, boulevard Serurier 75019 PARIS, ..........................................
52, avenue de la Concorde 93270 SEVRAN ................................
60, rue des Orteaux 75020 PARIS ................................................
28, avenue de 1 Opera 75002 PARIS ............................................
35, rue L. Sampaix 75010 PARIS .................................................
23, rue Bossuet 91160 LONGJUMEAU ........................................
32, rue de Mulhouse .. 68304 St LOUIS ...........................................
86, avenue de la Republique 93300 AUBERVILLIERS .............
6, place du General Leclerc 92300 LEVALLOIS .......................
3 a 5, rue de Metz 75010 PARIS ...................................................
27, boulevard du General Leclerc BP 29 - 59051 ROUBAIX .....
175 a 179, avenue J. Jaures _ 75019 PARIS ................................. TELEPHONE
( 78 ) 49.80.27
328.42.87
964.64.12
359.54.82
(41 1 41.73.03
(78 ) 20.08.94
797.01.49
267.15.00
453.13.20
( 89 ) 42.10.84
727.89.59
977.00.40
265.16.50
798.13.30
808.55.11
202.80.80
939.85.36
797.28.30
742.58.36
206.84.70
909777.85
(89) 67.13.37
352.75.94
757.67.34
770.13.08
(20 ) 70.02.1
202.50.72