Control Citroen DS3 2010 1.G Service Manual

89Access
Do not make any modifications to the alarm system, this could cause malfunctions.
Alarm System which protects and provides a deterrent against the theft of your vehicle. It provides two types of protection, exterior and interior, as well as a self-protection function.
Exterior perimeter
protection
The system detects opening of the vehicle. The alarm is triggered if anyone tries to enter the vehicle by forcing a door, the boot or the bonnet.
Interior volumetric
protection
The system detects any variation in the volume in the passenger compar tment. The alarm is triggered if anyone breaks a window or moves inside the vehicle. If you wish to leave a pet in the vehicle or a window par tially open, deactivate the interior volumetric protection.
Self-protection function
The system detects the putting out of ser vice of its components. The alarm is triggered if anyone tries to put the wires of the siren, the central control or the battery out of ser vice.

If an opening - door or boot - is not closed fully, the vehicle is not locked,
but the exterior perimeter protection will be activated after 45 seconds at the same time as the interior volumetric protection.
To be effective, this deactivation must be carried out each time the ignition is switched off.
Locking the vehicle with full
alarm
Activation
 Switch off the ignition and get out of the vehicle.  Lock or deadlock the vehicle using the locking button on the remote control. The alarm is activated; the indicator lamp on button A flashes once per second. The exterior perimeter protection is activated, 5 seconds after the locking button on the remote control is pressed. The interior volumetric protection is activated, 45 seconds after the locking button on the remote control is pressed.
Deactivation
 Unlock the vehicle using the unlocking button on the remote control. The alarm is deactivated; the indicator lamp on button A switches off.
Locking the vehicle with exterior
perimeter protection only
Deactivation of the interior volumetric protection
 Switch off the ignition.  Within ten seconds, press button A until the indicator lamp is lit continuously.  Get out of the vehicle.  Lock or deadlock the vehicle without delay using the locking button on the remote control. The exterior perimeter protection alone remains activated; the indicator lamp on button Aflashes once per second.
Reactivation of the interior volumetric protection
 Unlock the vehicle using the unlocking button on the remote control.
 Relock the vehicle using the remote control. The alarm is activated again with both types of protection; the indicator lamp on button Aflashes once per second.

91Access
If the alarm is triggered ten times in succession, the eleventh time will result in it becoming inactive. If the indicator lamp on button A flashes rapidly, this indicates that the alarm
was triggered during your absence. When the ignition is switched on, this flashing stops immediately. To avoid triggering the alarm when washing your vehicle, lock it using the key in the driver’s door lock.
Triggering of the alarm
This is indicated by sounding of the siren and flashing of the direction indicators for approximately thir ty seconds. After it has been triggered, both types of protection are again operational.
Failure of the remote control
 Unlock the vehicle using the key in the driver’s door lock.  Open the door; the alarm is triggered.  Switch on the ignition; the alarm stops.
Locking the vehicle without
activating the alarm
 Lock or deadlock the vehicle using the key in the driver’s door lock.
Malfunction
When the ignition is switched on, lighting of the indicator lamp on button A for ten seconds indicates a siren fault. Have it checked by a CITROËN dealer.
* According to country.
Automatic activation *
2 minutes after the last door or the boot is closed, the alarm is activated automatically.  To avoid triggering the alarm on entering
the vehicle, first press the unlocking button on the remote control.

1. Driver's electric window switch.2. Passenger's electric window switch.
Window controls System which opens or closes a window manually or automatically. It is fitted with anti-pinch protection on the driver's side.
The electric window switches
remain operational for approximately 45 seconds after the ignition is switched off or until a door is opened. If, during this period of 45 seconds, you open a door while operating a window, the window stops. Any new operation of the window switch will only be taken into account after the door has closed.
 Press or pull the switch. The window stops as soon as the switch is released.
Passenger's electric
window
There are two methods of operation:
Driver's electric window
- manual mode Press or pull the switch without passing the point of resistance. The window stops as soon as the switch is released.
- automatic mode
 Press or pull the switch fully. The window opens or closes completely when the switch is released.
 Pressing or pulling the switch again stops the movement of the window.

Doors
Opening
From outside
 After unlocking the vehicle using the remote control or the key, pull the door handle.
From inside
 Pull the door lever to open the door; this unlocks this vehicle completely.
Closing
When a door is not closed correctly:
- when the engine is running , this warning lamp comes on, accompanied by a message on the multifunction screen for a few seconds,
- when the vehicle is moving (speed higher than 6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message on the multifunction screen for a few seconds.
Version with deadlocking
The interior door controls do not operate when the vehicle is deadlocked.

95Access
System which provides full manual locking or unlocking of the doors from the inside.
Manual centralised control
Locking
 Press button A to lock the vehicle.
The red indicator lamp on the button comes on.
Unlocking
 Press button A again to unlock the vehicle. The red indicator lamp on the button switches off.
If one of the doors is open, central
locking from the inside does not take place.
If the vehicle is locked from the outside, the red indicator lamp flashes and button A is inactive.  In this case, use the remote control or the key to unlock the vehicle.
Automatic centralised
control
System which provides full automatic locking or unlocking of the doors and the boot while driving. You can activate or deactivate this function.
Locking
When the speed exceeds 6 mph (10 km/h), the doors and the boot lock automatically.
Unlocking
 Above 6 mph (10 km/h), press button A to unlock the doors and the boot temporarily.
If one of the doors is open, the automatic central locking does not take place. If the boot is open, the automatic central locking of the doors is active.

Activation
 Press button A for more than two seconds. A confirmation message appears on the multifunction screen, accompanied by an audible signal.
Deactivation
 Press button A again for more than two seconds. A confirmation message appears on the multifunction screen, accompanied by an audible signal.
To lock or unlock the doors mechanically in the event of a central locking system failure or flat battery.
Emergency control
Locking the driver’s door
 Inser t the key in the lock, then turn it to the left.
Unlocking the driver’s door
 Inser t the key in the lock, then turn it to the right.
Locking the passenger’s door
 Remove the black cap, on the edge of the door, using the key.  Inser t the key in the cavity, then turn it fully.  Remove the key and refit the cap.
Unlocking the passenger’s door
 Pull the interior door opening control.
In the event of a fault with the central locking system, you must disconnect the battery to lock the boot and so ensure the complete locking of the vehicle.

97Access
Boot
Opening
 After unlocking the vehicle using the remote control or the key, pull the handle and raise the tailgate.
Closing
 Lower the tailgate using the interior grab handle.
If the tailgate is not closed correctly:
- when the engine is running , this warning lamp comes on, accompanied by a message on the multifunction screen for a few seconds,
- when the vehicle is moving (speed above 6 mph (10 km/h)), this warning lamp comes on, accompanied by an audible signal and a message on the multifunction screen for a few seconds.
System for mechanical unlocking of the boot in the event of a battery or central locking malfunction.
Tailgate release
Unlocking
 Fold back the rear benchseat to gain access to the lock from inside the boot.  Inser t a small screwdriver into hole A of the lock to unlock the tailgate.

Lighting controls System for selection and control of the various front and rear lamps providing the vehicle's lighting.
The various front and rear lamps of the vehicle
are designed to adapt the driver's visibility progressively according to climatic conditions: - sidelamps, to be seen, - dipped beam headlamps to see without dazzling other drivers, - main beam headlamps to see clearly when the road is clear.
Main lighting
Other lamps are installed to fulfil the requirements of par ticular conditions of
visibility: - a rear foglamp to be seen from afar, - front foglamps for improved vision. - LED lamps to be seen during the daytime.
Additional lighting
Various automatic lighting control modes
are also available according to the following options: - guide-me-home lighting, - automatic illumination of headlamps.
Programming
In some weather conditions (e.g. low
temperature or humidity), the presence of misting on the internal sur face of the glass of the headlamps and rear lamps is normal; it disappears after the lamps have been on for a few minutes.

103Visibility
Model without AUTO lighting
Model with AUTO lighting
Manual controls
The lighting commands are issued directly by
the driver by means of the ring A and the stalk AB .
Automatic illumination of headlamps.
B. Stalk for switching the headlamp beam: pull the stalk to switch between dipped and main beam headlamps. In the lamps off and sidelamps modes, the driver can switch on the main beam headlamps temporarily ("headlamp flash") by maintaining a pull on the stalk.
A. Main lighting mode selection ring: turn it to position the symbol required facing the mark.
Lamps off.
Sidelamps only.
Dipped headlamps or main beam headlamps.
Displays
Lighting of the corresponding indicator lamp on
the instrument panel confirms the switching on of the lighting selected. The instrument panel has permanent back-lighting. Illumination of the instrument panel is therefore not linked to the exterior lighting.