warning Citroen DS3 DAG 2010 1.G User Guide

35Monitoring
Airbags
temporarily. This lamp comes on for a few seconds
when you turn on the ignition,then switches off.
This lamp should switch off when the engine is star ted.
If it does not switch off, contact a CITROËN dealer.
fixed. One of the airbag or seat belt pretensioner systems has a fault. Have it checked by a CITROËN dealer.
Warning lampis onCauseAction/Obser vations
Seat belt not fastened/unfastened
fixed then flashing accompanied by an increasing audible signal.
The driver and/or the front passenger has not fastened or has unfastened their seat belt.
Pull the strap then inser t the tongue in the buckle.
Power steering fixed. The power steering has a fault. Drive carefully at reduced speed. Have it checked by a CITROËN dealer.

With the engine running, when the needle is: - in zone A , the temperature is correct,
- in zone B , the temperature is too high; the central STOP warning lamp and the maximum temperature warning lamp 1 light up in red, accompanied by an audible signal and a message on the multifunction screen. You must stop as soon as it is safe to do so. Wait a few minutes before switching off the engine. Consult a CITROËN dealer.
Coolant temperature
indicator
After driving for a few minutes, the temperature and pressure in the cooling system increase.
To top up the level:  wait for the engine to cool down,  unscrew the cap by two turns to allowthe pressure to drop,  when the pressure has dropped, remove the cap,  top up the level to the "MA X" mark.

39Monitoring
System which informs the driver whetherthe engine oil level is correct or not. This information is indicated for a few seconds when the ignition is switched on, after the ser vice information.
Engine oil level indicator
The level read will only be correct if the vehicle is on level ground and the engine has been off for more than 15 minutes.
Oil level correct
Lack of oil
This is indicated by the flashing of "OIL" , linked with the ser vice warning lamp, accompanied by an audible signal and a message on the multifunction screen. If the lack of oil is confirmed by a check using the dipstick, it is essential that the level is topped up to prevent damage to the engine.
Oil level indicator fault
This is indicated by the flashing of "OIL- -" . Consult a CITROËN dealer.
There are 2 marks on the
dipstick: - A = max; never exceed this level (risk of damage to the
engine), - B = min; top up the level via the oil filler cap, using the
grade of oil suited to your engine.
Dipstick
Refer to the "Checks" section to locate the dipstick and the oil filler cap on your engine.

Monochrome screen A
This displays the following information: - time, - date, - ambient temperature (this flashes if there is a risk of ice), - status of the doors and boot, - audio sources (radio, CD...), - trip computer (refer to the "Instruments and Controls" section). Warning messages (e.g.: "Emission control
system faulty") or information messages (e.g.: "Boot open") may appear temporarily. These can be cleared by pressing the "ESC"button.
Displays on the screen
From the control panel of your Audio system, you can:  press the "MENU" button to gain access to the main menu ,
 press the "  " or "  " buttons to scroll through the items on the screen,  press the "MODE" button to change
the permanent application (date, audio source...),  press the "  " or "  " buttons to change a setting value,  press the "OK" button to confirm, or  press the "ESC" button to abandon the
operation in progress.
Controls
 Press the "MENU" button to gain access to the main menu , then press the "  " or "  " buttons to scroll through the various menus: - radio- CD, - vehicle configuration, - options, - display settings, - languages, - units.  Press the "OK" button to select the menu required.
Main menu

51Multifunction screens
Monochrome screen C
This displays the following information: - time, - date, - ambient temperature (this flashes if there is a risk of ice), - status of doors and boot, - audio sources (radio, CD, USB por t, jack socket etc.), - trip computer (refer to the "Instruments and controls" section).
Warning messages (E.g. "Emisions control system faulty") or information messages (E.g.: Automatic headlamps active") may appear temporarily. These can be cleared by pressing the "ESC" button.
Displays on the screen
From your Audio system control panel, you can:  press the "MENU" button to gain access to the main menu ,  press the "  " or "  " buttons to scroll through the items on the screen,  press the "MODE" button to change the permanent application (trip computer, audio source...),  press the "  " or "  " buttons to change a setting value,
 press the "OK" button to confirm, or  press the "ESC" button to abandon the operation in progress.
Controls
 Press the "MENU" button to gain access to the main menu : - audio functions, - the trip computer, - personalisation-configuration, - telephone (hands-free kit).  Press the "  " or "  " buttons to select the menu required, then confirm by pressing the "OK" button.
Main menu

With the Audio system switched on, once this menu has been selected you can activate
or deactivate the functions linked with use of the radio (RDS, REG, RadioText), the CD (introscan, shuffle, CD repeat) or the MP3 player (USB por t /jack socket). For more information on the "Audio functions" application , refer to the Audio system par t of the "Audio and Telematics" section.
"Audio functions"
menu
"Trip computer" menu
Once this menu has been selected, you can consult information concerning the status of the
vehicle (warnings log, status of functions, etc.)
Alert log
This summarises the active warning messages, displaying them in succession on the multifunction screen.
Status of functions
This summarises the status (active or inactive) of the vehicle's functions.
Enter distance to destination
This allows you to enter an approximate distance until your final destination.
 Press the "MENU" button to gain access to the general menu.
 Press the arrows, then the "OK" button to select the "Trip computer" menu.
 In the "Trip computer" menu, select one of the following applications:

55Multifunction screens
16/9 colour screen (MyWay)
It displays the following information automatically and directly: - time, - date, - altitude, - ambient temperature (the value displayed flashes if there is a risk of ice),
- check of the doors, - warning and vehicle function status messages, displayed temporarily,
- audio functions, - trip computer information (see the "Monitoring" section), - satellite navigation system information.
Displays on the screen
MyWay To select one of the applications, at the control panel:  press the dedicated "R ADIO" , "MUSIC" , "NAV" , "TR AFFIC" , "SETUP" or "PHONE" button for access to the corresponding menu,  turn the dial to change the selection,  press the dial to confirm the selection, or  press the "ESC" button to abandon the
current operation and return to the previous display.
Controls
For more information on these applications, refer to the "Audio and Telematics" section or to the specific user guide given to you with the other owner's documents.

Front demist - defrost
With the heating/ventilation
system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.
These markings on the control panel indicate the control positions for rapid demisting or defrosting of the windscreen and side windows.
With the manual air
conditioning system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.  Switch on the air conditioning by pressing the "A /C" button; the associated green
warning lamp comes on.
With Stop & Star t, when the demisting, air conditioning and air flow functions are activated, STOP mode is not available.

Front demist - defrost
With the heating/ventilation
system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.
These markings on the control panel indicate the control positions for rapid demisting or defrosting of the windscreen and side windows.
With the manual air
conditioning system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.  Switch on the air conditioning by pressing the "A /C" button; the associated green
warning lamp comes on.
With Stop & Star t, when the demisting, air conditioning and air flow functions are activated, STOP mode is not available.

Front demist - defrost
With the heating/ventilation
system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.
These markings on the control panel indicate the control positions for rapid demisting or defrosting of the windscreen and side windows.
With the manual air
conditioning system
 Put the temperature and air flow controls to the dedicated marked position.  Put the air intake control to the "Exterior air intake" position (manual control to the right or electric control with indicator lamp off).  Put the air distribution control to the " Windscreen" position.  Switch on the air conditioning by pressing the "A /C" button; the associated green
warning lamp comes on.
With Stop & Star t, when the demisting, air conditioning and air flow functions are activated, STOP mode is not available.