ignition Citroen DS3 RHD 2015 1.G Owner's Guide

Page 120 of 387

There is a risk of damage to the gearbox:
-  i f   you   press   the   accelerator   and  
b

rake   pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   selector   in
 t

he
n  

position   and   apply   the   parking   brake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from  n to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop
 
as   soon   as   possible.
F
Sel
ect position M for sequential c
hanging o
f
 
the
 
four
 
gears.
F
 
P

ush
 
the
 
selector
 
towards
 
the
 
+
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F
 
P

ull
 
the
 
selector
 
towards
 
the
 
-
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or

to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

Page 122 of 387

Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable   for   a   few   seconds   after  
c

oming   out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "ECO" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-
 
w

ith a manual gearbox ,
 
at
 
speeds
 
below
 
1

2
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever
 
into
 
neutral,
 
and
 
you
 
release
 
the
 
c

lutch
 
pedal.
-
 
w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
y

ou
 
press
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
s

elector in position
n
.
A

 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 
during
 a

 
journey.
 
It
 
rests
 
itself
 
to
 
zero
 
every
 t

ime
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t

he
 
key. STOP
  mode   is   not   invoked   when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "ECO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

Page 124 of 387

The system is reactivated automatically at   every   new   start   using   the   key.
Reactivation
This system requires a battery with a special specification   and   technology   (reference  
n

umbers   available   from   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop).
Fitting
  a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
In
 
the
 
event
 
of
 
a
 
fault
 
with
 
the
 
system,
 
the
 
"

ECO OFF"
 
switch
 
warning
 
lamp
 
flashes
 
then
 
c

omes
 
on
 
continuously.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
the
 
v

ehicle
 
may
 
stall.
 
All
 
of
 
the
 
instrument
 
panel
 
w

arning
 
lamps
 
come
 
on.
 
It
 
is
 
then
 
necessary
 
t

o
 
switch
 
off
 
the
 
ignition
 
and
 
start
 
the
 
engine
 
a

gain
 
using
 
the
 
key.
Operating fault Maintenance
Before doing anything under the b
onnet,   deactivate   the   Stop   &   Start  
s

ystem   to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
The
  Stop   &   Start   system   makes   use  
o

f   advanced   technology.   All   work  
o

n   this   type   of   battery   must   be   done  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Press the "ECO OFF"
 
switch
 
again.
The
 
system
 
is
 
active
 
again;
 
this
 
is
 
confirmed
 
b

y
 
the
 
switch
 
warning
 
lamp
 
going
 
off,
 
a

ccompanied
 
by
 
a
 
message
 
in
 
the
 
screen.

Page 126 of 387

System which prevents the vehicle from exceeding   the   speed   programmed   by   the  
d

river.
When
  the   programmed   speed   limit   is   reached,  
p

ressing   the   accelerator   pedal   in   the   normal  
m

anner   no   longer   has   any   effect.
The
  speed   limiter   is   switched on
 m
anually:
 it r

equires   a   programmed   speed   of   at   least  
20
  mph   (30   km/h).
The
  speed   limiter   is   switched off
 
by   manual  
o

peration   of   the   control.
The
  programmed   speed   can   be   exceeded  
t

emporarily   by   pressing   the   accelerator   firmly.
To
  return   to   the   programmed   speed,   simply  
s

low   down   to   a   speed   below   the   programmed  
s

peed.
The
 
p
rogrammed  
s
peed  
r
emains  
i
n  
t
he  
m
emory  
w

hen   the   ignition   is   switched   off.
Speed limiter
The speed limiter cannot, in any circumstances,   replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A
.
1.
 S
peed   limiter   mode   selection   thumb   wheel.
2.
 V
alue   decrease   button.
3.
 V
alue   increase   button.
4.
 S
peed   limiter   on   /   off   button.
Steering mounted controls
The programmed information is grouped t
ogether   in   the   instrument   panel   screen.
5.
 S

peed   limiter   on   /   off   indication.
6.
 S

peed   limiter   mode   selection   indication.
7.
 P

rogrammed   speed   value.
displays in the instrument panel

Page 128 of 387

Cruise control
System which automatically maintains the speed   of   the   vehicle   at   the   value   programmed  
b

y   the   driver,   without   any   action   on   the  
a

ccelerator
 ped
al.
The cruise control is switched on
 m

anually:
 it r

equires   a   minimum   vehicle   speed   of   25   mph  
(

40   km/h),   as   well   as   the   engagement   of:
-
 
f
ourth   gear   on   a   manual   gearbox,
-
 
s
econd   gear   on   a   or   automatic   or   electronic  
g

earbox,   in   sequential   mode,
-
 
p
osition   A   on   an   electronic   gearbox   or  
p

osition d  on   an   automatic   gearbox.
The cruise control is switched off
 m

anually
 o

r   by   pressing   the   brake   or   clutch   pedal   or   on  
t

riggering   of   the   trajectory   control   systems   for  
s

afety   reasons.
It
  is   possible   to   exceed   the   programmed   speed  
t

emporarily   by   pressing   the   accelerator   pedal.
To
  return   to   the   programmed   speed,   simply  
r

elease   the   accelerator   pedal.
Switching
  off   the   ignition   cancels   any  
p

rogrammed   speed   value. The
  controls   of   this   system   are   grouped  
t

ogether   on   stalk   A.
1.
 C

ruise   control   mode   selection   thumb   wheel.
2.
 V

alue   decrease   button.
3.
 V

alue   increase   button.
4.
 C

ruise   control   off/resume   button.Steering mounted controls
The cruise control cannot, in any
circumstances,  replace   the   need   to r

espect   speed   limits,   nor   can   it   replace   the
 n

eed   for   vigilance   on   the   part   of   the   driver.The
  programmed   information   is   grouped  
t

ogether   in   the   instrument   panel   screen.
5.
  C
ruise   control   off/resume   indication.
6.
  C
ruise   control   mode   selection   indication.
7.
  P
rogrammed   speed   value.
displays in the instrument panel

Page 131 of 387

129
ProgrammingOperating faults
If there is an operating fault, when r
everse   gear   is   engaged   this w

arning
 
lamp   comes   on   in   the   instrument   panel,
 a

ccompanied   by   an   audible   signal   (short   beep)
 a

nd
 
a
 
message   in   the   multifunction   screen.
You
 
can
 
activate
 
or
 
deactivate
 
the
 
system
 
by
 m
eans
 
of
 
the
 
multifunction
 
screen
 
configuration
 
m

enu.
 
The
 
system
 
state
 
is
 
memorised
 
when
 
s

witching
 
off
 
the
 
ignition.
For
 
more
 
information
 
on
 
access
 
to
 
the
 
parking
 
s

ensors
 
menu,
 
refer
 
to
 
" Vehicle
 
configuration"
 
o

r
 
" Vehicle
 
parameters"
 
section
 
for
 
your
 
m

ultifunction
 s

creen.
The
 
system
 
will
 
be
 
deactivated
 
a

utomatically
 
when
 
towing
 
a
 
trailer
 
or
 
w

hen
 
a
 
bicycle
 
carrier
 
is
 
fitted
 
(vehicle
 
f

itted
 
with
 
a
 
towbar
 
or
 
bicycle
 
carrier
 
r

ecommended
 
by
 
CITROËN). In
 
bad   or   wintry   weather,   ensure   that  
t

he
 
sensors   are   not   covered   with   mud,  
f

rost
 
or   snow.
driving

Page 138 of 387

C. Foglamp  selection   ring.
The   foglamps   operate   with   the   dipped   and   main  
b

eam
 h
eadlamps.
Rotate
  and   release   the   ring   C:
F
 
f
or wards   a   first   time   to   switch   on   the   front  
fo

glamps,
F
 
f
or wards   a   second   time   to   switch   on   the  
r

ear
 fo
glamp,
F
 
r
ear wards   a   first   time   to   switch   off   the   rear  
fo

glamp,
F
 
r
ear wards   a   second   time   to   switch   of   the  
f

ront   fog   lamps.
Model with front foglamps
and a rear foglamp Lighting on audible warning
When the ignition is switched off, all o
f   the   lamps   switch   off   automatically,  
u

nless   guide-me-home   lighting   is  
a

ctivated.
If
  the   lighting   is   switched   on   manually  
a

fter   switching   off   the   ignition,   there  
i

s   an   audible   signal   when   a   front   door  
i

s   opened   to   warn   the   driver   that  
t

hey   have   forgotten   to   switch   off   the  
v

ehicle's   lighting,   with   the   ignition   off.
In
  good   or   rainy   weather,   by   both   day  
a

nd   night,   the   front   foglamps   and   the  
r

ear   foglamp   are   prohibited.   In   these  
s

ituations,   the   power   of   their   beams  
m

ay   dazzle   other   drivers.
Do   not   forget   to   switch   off   the   front  
f

oglamps   and   the   rear   foglamp   when  
t

hey   are   no   longer   necessary.
Front
 
and
 
rear
 
foglamps
When
 
the
 
lighting
 
is
 
switched
 
off
 
automatically
 
(

with
 
AUTO
 
model)
 
or
 
when
 
the
 
dipped
 
h

eadlamps
 
are
 
switched
 
off
 
manually,
 
the
 
f

oglamps
 
and
 
sidelamps
 
will
 
remain
 
on.
F
 
T

urn
 
the
 
ring
 
rear wards
 
to
 
switch
 
off
 
the
 f

oglamps,
 
the
 
sidelamps
 
will
 
then
 
switch
 
off.

Page 139 of 387

137
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction   on   the   part   of   the   driver,   when   a   low   level  
o

f   external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   an  
a

dequate   level   or   after   the   windscreen   wipers  
a

re   switched   off,   these   lamps   are   switched   off  
a

utomatically   and   the   daytime   running   lamps  
c

ome   on.
Automatic illumination of
headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
ctivation   of   the   function   is   confirmed   by  
t

he   display   of   a   message.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  T
he   deactivation   of   the   function   is  
c

onfirmed   by   the   display   of   a   message.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting   come  
o

n,   this   warning   lamp   is   displayed  
o

n   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,  
a

ccompanied   by   an   audible   signal.
Contact
 
a
 
CITROËN   or   a   qualified   workshop  
w

orkshop.
Visibility

Page 140 of 387

LED daytime running lampsThis daytime lighting, a signature of the vehicle, comprises   two   sets   of   light-emitting   diodes  
(

LEDs),   located   in   vertical   housings   below   each  
h

eadlamp.
On
  starting   the   vehicle,   in   daylight   the   daytime  
r

unning   lamps   come   on   automatically,   if   the  
l

ighting   stalk   is   in   position   "0" or "AUTO" .
If
  the   sidelamps   and   headlamps   are   switched  
o

n   manually   or   automatically,   the   daytime  
r

unning   lamps   go   off.
In
 
fog
 
or
 
snow,
 
the
 
sunshine
 
sensor
 
m

ay
 
detect
 
sufficient
 
light.
 
Therefore,
 
t

he
 
lighting
 
will
 
not
 
come
 
on
 
au

tomatically.
Do
 
not
 
cover
 
the
 
sunshine
 
sensor,
 
c

oupled
 
with
 
the
 
rain
 
sensor
 
and
 
l

ocated
 
in
 
the
 
centre
 
of
 
the
 
windscreen
 
b

ehind
 
the
 
rear
 
view
 
mirror;
 
the
 
a

ssociated
 
functions
 
would
 
no
 
longer
 
be c

ontrolled.
Automatic guide-me-home
lighting
When the automatic illumination of headlamps f unctions   is   activated,   if   the   ambient   light   level  
i

s   low   the   dipped   beam   headlamps   remain   on  
w

hen   switching   off   the   ignition.
Settings
Activation and deactivation, as well as the duration   of   the   guide-me-home   lighting   can   be  
s

et   in   the   vehicle   configuration   menu   (except  
f

or   the   monochrome   screen   A,   for   which   the  
d

uration   is   fixed   at   60   seconds).

Page 144 of 387

Automatic rain sensitive
windscreen wipers
The windscreen wipers operate automatically, without   any   action   on   the   part   of   the   driver,   if  
r

ain   is   detected   (sensor   behind   the   rear   view  
m

irror),   adapting   their   speed   to   the   intensity   of  
t

he   rainfall.
Activation
This is controlled manually by the driver by pushing s talk A to the "AUTO" p osition.
It
  is   accompanied   by   the   illumination  
o

f   this   indicator   lamp   in   the  
i

nstrument   panel   and   a   message   in  
t

he   multifunction   screen.
Switching off
This is controlled manually by the driver by   moving   stalk   A   upwards,   returning   it   to  
p

osition

"0".
It
  is   accompanied   by   the   indicator   lamp
 i

n   the   instrument   panel   going   off   and   a
 m

essage   in   the   multifunction   screen.The
  automatic   wiping   must   be  r
eactivated   if   the   ignition   has   been   off  
f

or   more   than   one   minute,   by   pushing  
s

talk   A   downwards.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 61-70 71-80 ... 80 next >