ESP Citroen DS4 2011 1.G User Guide

83Comfort

2. Driver's side adjustment
4. Automatic visibility
programme
For maximum cooling or heating of the
passenger compar tment, it is possible
to exceed the minimum value 14 or the
maximum value 28.


)
Turn control 2
or 3
to the left until
"LO"
is displayed or to the right
until "HI"
is displayed. See "Front demisting - defrosting".



3. Passenger's side adjustment

The driver and front passenger can
each adjust the temperature to their
requirements.
The value indicated on the display
corresponds to a level of comfor t and not to a
temperature in degrees Celsius or Fahrenheit.


)
Turn control 2
or 3
to the left or to the right
respectively to decrease or increase this
value.
A setting around the value 21 provides
optimum comfort. However, depending on your
requirements, a setting between 18 and 24 is
normal.
You are advised to avoid a left /right setting
difference of more than 3.


Manual operation

If you wish, you can make a different choice
from that offered by the system by changing
a setting. The the "AU TO "
indicator lamps go
off; the other functions will still be controlled
automatically.


)
Pressing the "AU TO "
button returns the
system to completely automatic operation.






With Stop & Star t, when demisting has
been activated, the STOP mode is not
available.

Storing driving positions

System which registers the electrical settings
of the driver's seat and door mirrors. It enables
you to store and recall two positions using the
buttons on the side of the driver's seat.

Storing a position

Using buttons M/1/2



)
Switch on the ignition.

)
Adjust your seat and the door mirrors.

)
Press button M
, then press button 1
or 2

within four seconds.
An audible signal indicates that the position
has been stored.


Recalling a stored position

Ignition on or engine running



)
Press button 1
or 2
to recall the
corresponding position.
An audible signal indicates the end of the
adjustment.
Storing a new position cancels the
previous position. You can interrupt the current movement
by pressing button M
, 1
or 2
or by using
one of the seat controls.
A stored position cannot be recalled
while driving.
Recalling stored positions is
deactivated 45 seconds after switching
off the ignition.

93Comfort











Rear seats
Bench seat with fixed one-piece cushion and split backrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot.


)
Move the corresponding front seat for ward
if necessary.

)
Position the seat belt between the outer
and centre head restraints to avoid trapping
the belt when repositioning the seat
backrest.

)
Place the head restraints in the low
position.

Folding the backrest


)
Pull control 1
for wards to release the seat
back 2
.

)
Fold the seat back 2
on to the cushion.


)
Straighten the seat back 2
and secure it.

)
Check that the red indicator, located next
to the control 1
, is no longer visible.

)
Put the seat belt back in place on the side
of the seat backrest.


Repositioning the seat backrest

When repositioning the seat backrest,
take care not to trap the seat belts.

95Comfort





Mirrors

Each fitted with an adjustable mirror glass
permitting the lateral rear ward vision necessary
for over taking or parking. They can also be
folded for parking in confined spaces.

Demisting - Defrosting
Adjustment



)
Move control A
to the right or to the left to
select the corresponding mirror.

)
Move control B
in all four directions to
adjust.

)
Return control A
to the central position.


Door mirrors

The objects obser ved are, in reality,
closer than they appear.
Take this into account in order to
correctly judge the distance of vehicles
approaching from behind.




Folding



)
From outside: lock the vehicle using
the remote control or the key.

)
From inside: with the ignition on, pull the
control A
in the central position rear wards.


Unfolding



)
From outside: unlock the vehicle using
the remote control or the key.

)
From inside: with the ignition on, pull the
control A
in the central position rear wards. If the mirrors are folded using control A
,
they will not unfold when the vehicle is
unlocked. Pull again on control A
.
The folding and unfolding of the door
mirrors using the remote control can be
deactivated by a CITROËN dealer or a
qualified workshop.
Never fold or unfold the electric folding
mirrors manually.
If your vehicle is fitted with heated
mirrors, the demisting-defrosting
operates with the engine running, by
switching on the heated rear screen
(refer to the "Rear screen demist-defrost"
page).

Automatic tilting in reverse gear

System which provides a view of the ground
during parking manoeuvres in reverse gear.


Programming



)
With the engine running, engage reverse
gear.

)
Select and adjust the left-hand and right-
hand mirrors in succession.
The adjustment is stored immediately.


Switching on



)
With the engine running, engage reverse
gear.

)
Move control A
to the right or to the left to
select the corresponding mirror.
The glass of the mirror selected tilts
downwards, in accordance with its
programming.


Switching off



)
Exit reverse gear and wait ten seconds.
or


)
Return control A
to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initial
position:


- if the speed exceeds 6 mph (10 km/h),

- if the engine is switched off.

This system allows automatic simultaneous locking of the doors and boot as soon as the speed of the vehicle exceeds 6 mph (10 km/h).

Anti-intrusion security


Operation

Activation/Deactivation

You can activate or deactivate this function
permanently.


)
With the ignition on, press this button
until an audible signal star ts and a
corresponding message is displayed. If one of the doors or the boot is open,
the automatic central locking does not take
place.
This is signalled by the sound of the
locks rebounding, accompanied by
illumination of this warning lamp in the
instrument panel, an audible signal
and the display of an aler t message.

Carr ying long and voluminous
objects

If you want to drive with the boot open,
you should press the central locking
button to lock the the doors. Other wise,
every time the speed of the vehicle
exceeds 6 mph (10 km/h), the locks
will rebound and the alerts mentioned
above will appear.
In the event of a serious impact with
deployment of an airbag, the vehicle's
doors unlock automatically to allow the
exit of occupants and access for the
security services.

Pressing the central locking button unlocks
the vehicle.
Above 6 mph (10 km/h), this locking is
temporary. The state of the system stays in memory when
switching off the ignition.

123Visibility


Model without AUTO lighting



Model with AUTO lighting



Manual controls

The lighting commands are issued directly
by the driver by means of the ring A
and the
stalk B
.





Sidelamps (luminous signature).
Automatic illumination of headlamps.

B.
Stalk for switching headlamps: pull the stalk
towards you to switch the lighting between
dipped and main beam headlamps.
In the lamps off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
A.
Main lighting mode selection ring: turn it
to position the symbol required facing the
mark.
Lamps off.
Sidelamps.
Dipped headlamps or main beam
headlamps.

Displays

Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on. Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other users.

This function is assured:


- in countries where it is imposed by
regulations,
by illumination of the dipped beam
headlamps associated with illumination of
the sidelamps and number plate lamps; this
function cannot be deactivated.

- for other countries where it is provided,
by illumination of dedicated lamps
associated with illumination of the
sidelamps and number plate lamps; this
function can be activated or deactivated via
the vehicle configuration menu.

The instruments and controls (multifunction
screen, air conditioning control panel, ...) are
not illuminated, except in night mode with
manual or automatic illumination of headlamps.








Daytime running lamps

The lighting control must be in position "0"
or
"AU TO "
(day mode).

125Visibility

Switching off the lighting
when switching off the ignition
When the ignition is switched off, all
of the lamps switch off immediately,
except for the dipped beam headlamps
if automatic guide-me-home lighting is
activated.
Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.

Switching on



)
With the ignition off, "flash" the headlamps
using the lighting stalk.

)
A fur ther "headlamp flash" switches the
function off.



Switching off

The manual guide-me-home lighting switches
off automatically after a set time.








Manual guide-me-home
lighting

Switching on the lighting
when switching on the ignition
To reactivate the lighting control stalk, turn
the ring A
to position "0"
- lighting off, then
to the position of your choice.
If the lighting is switched on manually after
switching off the ignition, there is an audible
signal when a front door is opened to warn
the driver that they have forgotten to switch
off the vehicle's lighting, with the ignition off.
They switch off automatically after a period
which depends on the state of charge of the
battery (entry to energy economy mode).




















Parking lamps

Side markers for the vehicle by illumination of
the sidelamps on the traffic side only.


)
Within one minute of switching off the
ignition, operate the lighting control stalk up
or down depending on the traffic side (for
example: when parking on the left; lighting
control stalk upwards; the right hand
sidelamps are on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator warning lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the central position.

Cornering lighting


With dipped or main beams, this function
makes use of the beam from a front foglamp to
illuminate the inside of a bend, when the vehicle
speed is below 25 mph (approximately 40 km/h)
(urban driving, winding road, intersections,
parking manouevres...).

Switching on



with cornering lighting


without cornering lighting




Switching off

The system does not operate:


- below a cer tain angle of rotation of the
steering wheel,

- above 25 mph (40 km/h),

- when reverse gear is engaged,

The system is activated by default.



Programming

The system is activated or
deactivated in the vehicle
configuration menu. This function starts:


- when the corresponding direction indicator
is switched on,
or

- from a cer tain angle of rotation of the
steering wheel.

1.
Front cour tesy lamp


2.
Front map reading lamps


3.
Rear courtesy lamp


4.
Rear map reading lamps














Courtesy lamps

In this position, the courtesy
lamp comes on gradually:

Front and rear courtesy lamps



- when the vehicle is unlocked,

- when the key is removed from the ignition,

- on opening a door,

- when the remote control locking button is
used to locate your vehicle.
It switches off gradually:


- when the vehicle is locked,

- when the ignition is switched on,

- 30 seconds after the last door is closed.
Permanently off.
Permanent lighting. In permanent lighting mode, the
lighting time varies according to the
circumstances:


- with the ignition off, approximately
ten minutes,

- in energy economy mode,
approximately thirty seconds,

- with the engine running, unlimited.
When the cour tesy lamp is in the
"permanent lighting" position, the rear
courtesy lamp also comes on, except if
it is in the "permanently off " position.
To switch off the rear cour tesy lamp,
put it in the the "permanently off "
position.


Front and rear map reading
lamps


)
With the ignition on, press the
corresponding switch.

Take care not to put anything in contact
with the cour tesy lamps.