ESP Citroen DS4 2012 1.G User Guide

A few seconds after the ignition is switched
on, the distance recorder resumes its normal
operation.
The spanner remains on.
The distance remaining may be weighted by the time factor, depending on the type of driving.
Therefore, the spanner may also comeon if you have exceeded the two year service interval.
Service indicator zero reset

After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the ".../000"
trip distance
recorder zero reset button, ) switch on the ignition; the distance recorder
display begins a countdown,
) when the screen indicates "=/0"and thespanner disappears, release the button.

This operation cannot be carried out while a reminder of the ser vicing information is being displayed.
Following this operation, if you wish todisconnect the battery, lock the vehicleand wait at least five minutes for thezero reset to be registered.


Recalling the service information

You can recall the ser vice information at anytime. )Briefly press the ".../000"
trip distance recorder zero reset button.
The ser vice information is displayed for afew seconds, in the total distance recorder
line or in the type 2 instrument panel central screen.
Service overdue
For a few seconds after the ignition is switched on,
the spanner flashes
to indicate that the servicemust be carried out as soon as possible. Example:
the ser vice is overdue by 180 miles(300 km).
For a few seconds after the ignition is switched on,
the screen indicates:

Monitoring
Manual test in the type 2 instrument panel central screen
This function allows you to check the status of the vehicle systems (reminder of the "activated"/"deactivated" status of the configurable functions) and to
display the aler ts log.
)With the engine running, to star t a manual
test, briefly press the ".../000"button on
the instrument panel. The followin
g information appears successively in the instrument panel central screen:
- engine oil level indicator(see corresponding section),
- ser vice indicator (see correspondingsection),
- under-inflation detection (if your vehicle
is fitted with this system; see the "Safety"section),
- current warnings and aler t messages,
if any (see corresponding section for the
warning lamp or system concerned),
- status of configurable functions(see "Multifunction screens").

This information also appears everytime the ignition is switched on(automatic test).

Colour screen and map
It displays the following information automatically and directly:
- time,
- date,
- altitude,
- ambient temperature
(the value displayed flashes if there is a risk of ice),
- parking sensor information,
- parking space measurement,
- audio functions,
- directory and telephone information,
- satellite navigation system information.
Displays in the screen
From the navigation system control panel, to
select one of the applications: ) press the dedicated "RADIO"
, "MUSIC","NAV"
, "TRAFFIC", "PHONE"
or "SETUP"
button for access to thecorresponding menu, )
turn the dial A
to select a function, an item in a list,)
press button Bto confirm the selection,
or
) press the "ESC"button to abandon thecurrent operation and return to the previous
display.

Controls

For more information on these applications,
refer to the "Audio and Telematics" section.

83Comfort

2. Driver's side adjustment 4. Automatic visibilityprogramme

For maximum cooling or heating of thepassenger compar tment, it is possibleto exceed the minimum value 14 or themaximum value 28.)
Turn control 2or 3
to the left until
"LO"is displayed or to the right until "HI"
is displayed. See "Front demistin
g - defrosting".

3. Passenger's side adjustment
The driver and front passenger can each adjust the temperature to their requirements.
The value indicated on the displaycorresponds to a level of comfor t and not to a
temperature in degrees Celsius or Fahrenheit.
)Turn control 2or 3to the left or to the right respectively to decrease or increase this
v
alue.
A setting around the value 21 provides optimumcomfort. However, depending on your requirements,
a setting between 18 and 24 is normal. You are advised to avoid a left/right setting
difference of more than 3.

Manual operation

If you wish, you can make a different choice from that offered by the system by changinga setting. The the "AUTO"indicator lamps gooff; the other functions will still be controlled
automatically.
) Pressing the "AUTO"
button returns the system to completely automatic operation.
With Stop & Start, when demisting hasbeen activated, the STOP mode is not available.

Storing driving positions
System which registers the electrical settings of the driver's seat and door mirrors. It enablesyou to store and recall two positions using the buttons on the side of the driver's seat.

Storing a position

Usin
g buttons M/1/2
)
Switch on the ignition. )
Adjust your seat and the door mirrors. )
Press button M
, then press button 1or 2within four seconds.
An audible signal indicates that the position
h
as been stored.
Recalling a stored position

I
gnition on or engine running
)Press button 1
or 2to recall the corresponding position.
An audible signal indicates the end of the
adjustment.
Storing a new position cancels theprevious position.
You can interrupt the current movementby pressing button M, 1
or 2
or by using one of the seat controls.
A stored position cannot be recalled
while driving.
Recalling stored positions is deactivated 45 seconds after switching off the ignition.

93Comfort











Rear seats
Bench seat with fixed one-piece cushion and split backrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot.
)Move the corresponding front seat forward
if necessary. )Position the seat belt between the outer and centre head restraints to avoid trapping
the belt when repositioning the seat backrest. )Place the head restraints in the lowposition.
Folding the backrest
)
Pull control 1
forwards to release the seat
back 2
. )
Fold the seat back 2on to the cushion.

)
Straighten the seat back 2
and secure it. )
Check that the red indicator, located next
to the control 1, is no longer visible.) Put the seat belt back in place on the side of the seat backrest.

Repositioning the seat backrest

When repositioning the seat backrest,take care not to trap the seat belts.

95
Comfort





Mirrors

Each fitted with an adjustable mirror glass permitting the lateral rear ward vision necessary for overtaking or parking. They can also be
folded for parking in confined spaces.

Demisting - Defrosting
Adjustment
)
Move control A
to the right or to the left to select the corresponding mirror. )
Move control B
in all four directions to
adjust. ) Return control Ato the central position.


Door mirrors
The objects obser ved are, in reality, closer than they appear. Take this into account in order to correctly judge the distance of vehicles approaching from behind.




Folding
)
From outside: lock the vehicle usingthe remote control or the key.)
From inside: with the ignition on, pull the control A
in the central position rear wards.


Unfolding
)
From outside: unlock the vehicle usingthe remote control or the key.)
From inside: with the ignition on, pull the control A
in the central position rear wards.

If the mirrors are folded using control A , they will not unfold when the vehicle is unlocked. Pull again on control A.

The folding and unfolding of the door mirrors using the remote control can be deactivated by a CITROËN dealer or a qualified workshop.
Never fold or unfold the electric folding mirrors manually.
I
f your vehicle is fitted with heated
mirrors, the demisting-defrostingoperates by switching on the heatedrear screen (refer to the "Rear screen
demist-defrost" page).
The rear screen demist - defrost can onl
yoperate when the engine is running.

Automatic tilting in reverse gear
System which provides a view of the ground
during parking manoeuvres in reverse gear.
Programming
)
With the engine running, engage reverse gear. )
Select and adjust the left-hand and right-
hand mirrors in succession.
The adjustment is stored immediately.


Switching on
)
With the engine running, engage reverse gear. )
Move control Ato the right or to the left to select the corresponding mirror.
The glass of the mirror selected tiltsdownwards, in accordance with its
programming.


Switching off
)Exit reverse gear and wait ten seconds.
or )Return control A
to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initialposition:


- if the speed exceeds 6 mph (10 km/h),

- if the engine is switched off.

This system allows automatic simultaneous locking of the doors and boot as soon as the speed of the vehicle exceeds 6 mph (10 km/h).
Anti-intrusion security
Operation

Activation
/Deactivation

You can activate or deactivate this function
permanently.
) With the ignition on, press this buttonuntil an audible signal star ts and acorresponding message is displayed. If one of the doors or the boot is open,
the automatic central lockin
g does not take place.
This is signalled by the sound of thelocks rebounding, accompanied byillumination of this warning lamp in the
instrument panel, an audible signal
and the display of an aler t message.
Carrying long and voluminousobjects If you want to drive with the boot open,you should press the central locking button to lock the the doors. Other wise,
every time the speed of the vehicle exceeds 6 mph (10 km/h), the lockswill rebound and the alerts mentioned above will appear.


In the event of a serious impact with deployment of an airbag, the vehicle'sdoors unlock automatically to allow the exit of occupants and access for the security services.

Pressin
g the central locking button unlocks
the vehicle.
Above 6 mph (10 km/h), this locking is
temporary. The state o
f the system stays in memory when
switchin
g off the ignition.

Visibility
Model without AUTO lighting

Model with AUTO li
ghting


Manual controls

The lighting is controlled directly by the driver
by means of the ring A and the stalk B.
Sidelamps (luminous signature).
Automatic illumination of headlamps.
B
. Stalk for switching headlamps: pull the stalk
towards
you to switch the lighting between
dipped and main beam headlamps.
In the lamps off and sidelamps modes, the
driver can switch on the main beam headlamps
temporaril
y ("headlamp flash") by maintaining a
pull on the stalk. A
.Main lighting mode selection ring: turn it
to position the symbol required facing themark.
Lamps o
ff.
Sidelamps.
Di
pped headlamps or main beam headlamps.

Displays

Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
li
ghting selected is on. Da
ytime lighting, compulsory in cer tain countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other users.

Thi
s function is assured:


- in countries where it is imposed byregulations,
by illumination of the dipped beam headlamps associated with illumination of
the sidelamps and number plate lamps;
this function cannot be deactivated.

- for other countries where it is provided,
by illumination of dedicated lamps associated with illumination of the
sidelamps and number plate lamps; this
function can be activated or deactivated viathe vehicle configuration menu.

The instruments and controls
(multifunctionscreen, air conditioning control panel, ...)are not illuminated, except in night mode with
manual or automatic illumination of headlamps.
Daytime running lamps

The lighting control must be in position "0"
or "AUTO"
(day mode).