Citroen DS5 HYBRID4 2013 1.G Owner's Manual

Front seats
Manual
1.Adjustments to the height and angleof
the head restraintTo raise it, pull upwards.
To lower it, press on the lug and the headrestraint at the same time.2.Adjustment of the backrest angleTurn the wheel to adjust the angle of thebackrest. 3.Adjustment of the seat heightRaise or lower the control lever the number
of times required to obtain the desiredposition.4.Forwards-backwards adjustment of the
seat position Lift the control bar and slide the seatforwards or backwards.5.Adjustment of the driver's lumbar
supportTurn the wheel to obtain the desired level of lumbar support.

Comfort
Switch on the ignition or star t the engine if the vehicle has gone intoeconomy mode.
The electric functions of the driver's seat are active for about 45 secondsafter opening the front door. They are deactivated about 45 seconds after switching off the ignition and in economy mode.

To reactivate them, switch on the ignition.

Electric
1.Adjustment of the seat cushion angleand height, and for wards-backwards adjustment)Raise or lower the front of the control to adjust the seat cushion angle. )Raise or lower the rear of the control to raise or lower the seat.)Simultaneously raise or lower the frontand rear of the control in order to raise or lower the entire seat. 2.Adjustment of the backrest angle Move the control forwards or backwards to adjust the backrest angle. 3.Adjustment of driver's lumbar support Press the control switches to obtain the
desired level of lumbar suppor t.
4. Manual adjustment of the cushion
Pull on the grip to adjust the length of thecushion.

Storing driving positions
System which stores the electrical settings
of the driver's seat and the head-up display settings. It enables you to store up to two positions using the buttons on the side of the driver's seat.

Storing a position usingbuttons M / 1 / 2

)
Switch on the ignition. )
Adjust your seat and the head-up display.)
Press button M
, then press button 1or 2within four seconds.
An audible signal indicates that the positionhas been stored.
Storing a new position cancels the previous
position.

Recalling a stored position
)Briefly press button 1
or 2to recall the corresponding position.
An audible signal indicates the end of the
adjustment.
You can interrupt the current movementby pressing button M, 1
or 2
or by using one of the seat controls. A stored position cannot be recalled while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.

Comfort
The head restraint is fitted with a framewith notches which prevents it from lowering; this is a safety device in caseof impact.
The adjustment is correct when theupper edge of the head restraint is level with the top of the head.Never drive with the head restraints removed; they must be in place andadjusted correctly.

Head restraint height and
angle adjustment
)To raise a head restraint, pull it upwards. )To remove the head restraint, press thelug A
and pull the head restraint upwards. )To put the head restraint back in place,
engage the head restraint stems in the
openings keeping them in line with the seat back. )To lower the head restraint, press the lug Aand push down on the head restraint at thesame time. )To a djust the angle of the head restraint, tilt
its lower part forwards or rearwards.

Massage function
This function provides the driver with a back
massage. It only operates when the hybridsystem is active or in STOP mode of the Stop & Start system.

Activation
)
Press this switch.


Its indicator lamp comes on and the massa
ge
function is activated for a period of 1 hour.
Durin
g this time, massage is per formed in 6 cycles of 10 minutes (6 minutes of massage
followed by 4 minutes break).
After one hour, the function is deactivated, the
indicator lamp goes off.


Deactivation

You can deactivate the massage
function at an
y time by pressing this
switch, its indicator lamp goes off.
Heated seats control
With the hybrid system active, the front seatscan be heated individually.
)Use the adjustment wheel to switch on and
select the level of heating required:

0: Off.1:
Low. 2
:
Medium. 3
: High.

105
Comfort








Rear seats
Bench seat with split cushion and backrest (left hand 2/3, right hand 1/3) which can be folded individually to adapt the load space in the boot.
)Move the corresponding front seat forward
if necessary. )Place the head restraints in the low position or remove them. )Remove the seat belt from its guide.
Folding the cushion
and backrest
)
Lift the cushion 1by hand, lifting from therear.

)
Tip the seat cushion 1
fully against the frontseat.
)
Keep the seat belt guide 2
held against the
vehicle.

)
Pull control 3forwards to release the seatback 4.)
Fold the seat backrest 4.

Repositioning the seat
backrest and cushion
)Keep the seat belt guide 2 held against the
vehicle to avoid trapping the seat belt whenrepositioning the seat. )Straighten the seat back 4while refitting
the head restraints and secure it.)Check that the red indicator, located next to
the control 3 , is no longer visible.

)
Reposition the cushion 1.)
Release the seat belt guide 2.)
Put the seat belt back in place in the guide.

When repositioning the seat backrest,take care not to trap the seat belts.
)Remove the seat cushion 1
from its fixings by pulling upwards.






Removing the seat cushion

Refittin
g the seat cushion
)Position the seat cushion 1
ver tically in itsfixings.

107
Comfort
These have one position for use (up) and a stowed position (down).
They can also be removed.
To remove a head restraint: ) release the backrest using control 1,)
tilt the backrest 2
slightly forwards, )
pull the head restraint upwards to the stop, )
then, press the lug A.
Rear head restraints

Never drive with the head restraintsremoved; they must be in place and correctly adjusted.









Fan cooling of the high voltage battery


This system does not work continuously,
but adapts the force of the fan cooling to the
requirements of the battery.
Its operation can be heard at the rear, even if
the vehicle is stopped after a run.
If the air intake is blocked, the batter
y mayoverheat, damaging the battery and causing a
loss of performance of the hybrid system.
For the best use of the high voltage battery, please follow these recommendations: - do not obstruct the air intake with loose ar ticles, other wise, the battery may overheat, causing a loss of performance of the hybrid system- do not spill fluids, as this may cause damage to the battery.
The high voltage battery has an air cooling system, comprising an air intake
(located on the side of the left hand rear seat) and a fan (located behind the lefthand boot trim panel).

Mirrors
Each fitted with an adjustable mirror glassproviding the lateral rearward vision necessaryfor overtaking or parking. They can also be
folded for parking in confined spaces.
Door mirrors

If the mirrors are folded using control A ,they will not unfold when the vehicle is unlocked.


The folding and unfolding of the door mirrors using the electronic key can bedeactivated by a CITROËN dealer or a qualified workshop.
Fold the mirrors when putting your vehicle through an automatic car wash.
The objects observed are, in reality, closer than they appear.Take this into account in order to correctly judge the distance of vehicles approaching from behind.

Demisting - Defrosting
Ad
justment
)
Turn control A
to the right or to the left toselect the corresponding mirror. )
Move control Ain all four directions toadjust. )
Return control Ato the central position.
Folding
Automatic: lock the vehicle using the electronickey.


Unfolding
Automatic: unlock the vehicle using the electronic key.
Manual: with the ignition on, move control Adownwards.
Manual: with the i
gnition on, move control Aupwards.
Demisting-defrosting of the door
mirrors operates by switching on
the heated rear screen.
The rear screen demisting - defrostingcan only operate when the hybridsystem is active. For more in
formation, refer to the "Rear screen demist-defrost" section.