Citroen DS5 HYBRID4 2013 1.G Manual PDF

Monitoring
Service indicator
More than 1 800 miles (3 000 km)remain before the next service is due
When the ignition is switched on, no ser vice information appears in the screen. S
ystem which informs the driver when the next ser vice is due, in accordance with themanufacturer's servicing schedule.
The point at which the ser vice is due is calculated from the last indicator zero reset. Itis determined by two parameters:


- the distance travelled,

- the time elapsed since the last ser vice. Between 600 miles (1 000 km)and 1 800 miles (3 000 km) remain before the next service is due
For 5 seconds after the ignition is switched on, the
spanner symbolising the ser vice operations comes
on. The distance recorder display line indicates the
distance remaining before the next ser vice is due.
Example:
1 700 miles (2 800 km) remain before
the next service is due.
For 5 seconds after the ignition is switched on, thescreen indicates:
5 seconds a
fter the ignition is switched on,the spanner goes off; the distance recorder f
resumes its normal operation. The screen thenindicates the total and trip distances.
Less than 600 miles (1 000 km)
remain before the next service is due
Example:
560 miles (900 km) remain before
the next service is due.
For 5 seconds after the ignition is switched on,
the screen indicates:
5 seconds after the i
gnition is switched on,
the distance recorder resumes its normal
operation. The spanner remains onto indicate
that a service must be carried out soon.


Illumination of the key is accompaniedby a message in the instrument panel screen.

Service overdue
Every time the ignition is switched on, an
overdue service is immediately signaledby flashing of the spanner and the fixed
illumination of the Service warning lamp.

The distance remaining may be weighted by the time factor, dependingon the driving conditions.
Therefore, the spanner may also comeon if you have exceeded the period since the last service, indicated in the maintenance and warranty guide
.

Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account. 5 seconds a
fter the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on.
Service indicator
zero reset
After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the trip distance recorder
zero reset button,) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.
Retrieving the serviceinformation

You can access the service information at
any time. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for a few seconds, then disappears.

Monitoring
Engine oil level indicator
Oil level incorrect
This is indicated by a message in the instrument panel screen.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped up to avoid damage to the engine.

Oil level indicator fault

This is indicated by a message in the
instrument panel screen. Contact a CITROËN
dealer or a qualified workshop.


Dipstick

Refer to the "Checks" section to locate the
dipstick and the oil filler cap on your engine.
System which informs the driver whether theengine oil level is correct or not.
This information is indicated for a few secondswhen the ignition is switched on, after theservice information.

The level read will only be correct if the vehicle is on level ground and the engine has been off for more than30 minutes.
There are
2 marks on the dipstick:


- A= max; never exceed this
level,

-
B= min; top up the level via
the oil filler cap, using the grade of oil suited to your engine.
Oil level correct
This is indicated by a message in the instrument panel screen.

System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
Lighting dimmer

Activation

When the lighting is on:
)press the button to change the brightness
of the instruments and controls,)when the level of brightness required isreached, release the button.

Deactivation

When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,pressing the button does not have any effect.

System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thir ty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelledduring a day or other period since it was reset
to zero by the driver. ) With the ignition on, press the button until
zeros appear.



Trip distance recorder
To c o nform to legislation in the countryyou are crossing, change the units of distance (miles or km) via the configuration menu.

73Monitoring
System allowing cer tain screens to be switched
off for night driving (available only with eMyWay).
The instrument panel remains on with the
vehicle speed, electronic gearbox gear
selected, cruise control or speed limiter
information, if in use, and the low fuel alerts if necessary.
If there is an aler t or a change in a function
or to a setting, the black panel mode isinterrupted.
Black panel (black screen)
w
ith eMyWay

For more information, refer to the eMyWay par t of the "Audio andtelematics" section.

The analogue clock does not have anadjustment button.
To set the time, refer to the section relating to
the screen (audio system) configuration menu.
The clock is synchronised with the screen time;
once the the setting has been confirmed in
the screen, the hands will turn to synchronise
with the screen, and each time the ignition is switched on.

Setting the date and time
Audio system / Bluetooth

Press MENU.


Using the arrows, select " Personalisation-
configuration
" and confirm.
Usin
g the arrows, select "Displayconfiguration" and confirm.

Usin
g the arrows, select "Date and timeadjustment" and confirm.

Select the settin
g to be modified. Confirm
by pressing OK
, then make the change and confirm again to save the modification.

Adjust the settings one by one, confirming by
pressing the OK
button. Next select the " OK"tab on the screen then confirm to exit from the"Date and time adjustment " menu.

75
Monitoring
eMyWay
Press SETUP
to display the "Configuration " menu.
Select "Display configuration
" and confirm.
Select " Set date and time" and confirm.
Select "Synchronize the minutes withGPS" so that setting the minutes is doneautomatically by satellite reception.

Adjust the settings one by one.
Then select " OK" on the screen and confirm to
save the settings.

The clock, located in the dashboard, is synchronised with the time in the screen. It is set once the time is adjusted using
the " SETUP" menu and every time theignition is switched on.
Select the settin
g to adjust. Confirm by pressing OK
, then adjust the setting and confirm again to save the modification.

Tr i p c o m p u t e r
)When the trip required is displayed, press
the control for more than two secondsor use the left hand thumb wheel of the
steering mounted controls.


Instrument panel screen
Information displa
y
)Press the button on the end of the wiper control stalk
to display the various tabs in succession.- Th
e current information tab with:
●
the range,
●
the current fuel consumption,
-
Trip "1"
with:
●
the average speed, for the first trip.
●
the average fuel consumption,


-
Trip "2"with:
●
the average speed, for the second trip.
●
the consumption history (with
16/9 colour screen),
●
the average fuel consumption,




Reset trip
- Radio or media.
- Satellite navigation.

77Monitoring
If dashes are displayed continuously while driving in place of the digits,contact a CITROËN dealer or a qualified workshop.
This value may vary following a change in the style of driving or the relief, resulting in a significant change in the current fuel consumption.
Trip computer, a few definitions…

Range
(miles or km)
This indicates the distance
which can still be travelled with
the fuel remaining in the tank
in relation to the average fuelconsumption over the last few
miles (kilometres) travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
This function is only displayed from20 mph (30 km/h).
Current fuel consumption
(mpg or l/100 km or km/l)This is the average fuel consumption
during the last few seconds.

Average fuel consumption
(mpg or l/100 km or km/l)
This is the average fuel
consumption since the last tripcomputer zero reset.
Average speed
(mph or km/h)
This is the average speed calculated
since the last trip computer zero reset
(ignition on).

Reset history
)With trip 2 displayed, press the button (on
the end of the wiper stalk) for more than
two seconds to reset the history to zero.

Trips
"1"
and "2"are independent but their use
is identical.
For example, trip "1"
can be used for daily figures, and trip "2"
for monthly figures.

002
Access