reset Citroen DS5 HYBRID4 2013 1.G Owner's Manual

49Hybrid system








Consumption of your hybrid in the screen

Average consumption over the last 5 minutes.
"60 % H
ybrid Use" corresponds to 60 % of the cumulative
running time with the addition of the hybrid system and
40 % of the time with the Diesel engine only (with no contribution from the hybrid system).


For more information on the trip computer, refer to the corresponding section.
Resetting the history

With the hybrid system active, when trip 2 displayed, press
the control for 2 seconds to reset the history to zero.

Instrument panel
1.
Energy consumption / generation indicator (available power as a percentage).
For more information refer to the "H
ybrid
system" section.2. Fuel gauge.3.Engine coolant temperature gauge. 4.
Speedometer (mph or km/h).5.
Cruise control or speed limiter
settings.A
.Main lighting and controls dimmer.
B.- Successive shor t presses: under-inflation
detection, recall servicin
g information, alert
log.
- Long press: reset the function selected to
zero (ser vice indicator or trip recorder). 6
. Gear engaged.
7.Instrument panel screen: electrical flow,
trip recorder, aler t messa
ges or state of functions (e.g.: oil pressure, battery, door open, ...), trip computer, media, satellite
navigation.8. Digital speedometer (mph or km/h). 9.Ready lamp: indicates that the vehicle is
ready to drive.
Dials and screens
Control buttons

Monitoring
Service indicator
More than 1 800 miles (3 000 km)remain before the next service is due
When the ignition is switched on, no ser vice information appears in the screen. S
ystem which informs the driver when the next ser vice is due, in accordance with themanufacturer's servicing schedule.
The point at which the ser vice is due is calculated from the last indicator zero reset. Itis determined by two parameters:


- the distance travelled,

- the time elapsed since the last ser vice. Between 600 miles (1 000 km)and 1 800 miles (3 000 km) remain before the next service is due
For 5 seconds after the ignition is switched on, the
spanner symbolising the ser vice operations comes
on. The distance recorder display line indicates the
distance remaining before the next ser vice is due.
Example:
1 700 miles (2 800 km) remain before
the next service is due.
For 5 seconds after the ignition is switched on, thescreen indicates:
5 seconds a
fter the ignition is switched on,the spanner goes off; the distance recorder f
resumes its normal operation. The screen thenindicates the total and trip distances.
Less than 600 miles (1 000 km)
remain before the next service is due
Example:
560 miles (900 km) remain before
the next service is due.
For 5 seconds after the ignition is switched on,
the screen indicates:
5 seconds after the i
gnition is switched on,
the distance recorder resumes its normal
operation. The spanner remains onto indicate
that a service must be carried out soon.


Illumination of the key is accompaniedby a message in the instrument panel screen.

Service overdue
Every time the ignition is switched on, an
overdue service is immediately signaledby flashing of the spanner and the fixed
illumination of the Service warning lamp.

The distance remaining may be weighted by the time factor, dependingon the driving conditions.
Therefore, the spanner may also comeon if you have exceeded the period since the last service, indicated in the maintenance and warranty guide
.

Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account. 5 seconds a
fter the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on.
Service indicator
zero reset
After each ser vice, the ser vice indicator mustbe reset to zero.
The procedure for resetting to zero is as
follows: ) switch off the ignition,)
press and hold the trip distance recorder
zero reset button,) switch on the ignition; the distance recorder
display begins a countdown,
) when the display indicates "=0", release
the button; the spanner disappears.
Retrieving the serviceinformation

You can access the service information at
any time. )Press the trip distance recorder zero reset button.
The ser vice information is displayed for a few seconds, then disappears.

System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.
Lighting dimmer

Activation

When the lighting is on:
)press the button to change the brightness
of the instruments and controls,)when the level of brightness required isreached, release the button.

Deactivation

When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,pressing the button does not have any effect.

System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thir ty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelledduring a day or other period since it was reset
to zero by the driver. ) With the ignition on, press the button until
zeros appear.



Trip distance recorder
To c o nform to legislation in the countryyou are crossing, change the units of distance (miles or km) via the configuration menu.

Tr i p c o m p u t e r
)When the trip required is displayed, press
the control for more than two secondsor use the left hand thumb wheel of the
steering mounted controls.


Instrument panel screen
Information displa
y
)Press the button on the end of the wiper control stalk
to display the various tabs in succession.- Th
e current information tab with:
●
the range,
●
the current fuel consumption,
-
Trip "1"
with:
●
the average speed, for the first trip.
●
the average fuel consumption,


-
Trip "2"with:
●
the average speed, for the second trip.
●
the consumption history (with
16/9 colour screen),
●
the average fuel consumption,




Reset trip
- Radio or media.
- Satellite navigation.

77Monitoring
If dashes are displayed continuously while driving in place of the digits,contact a CITROËN dealer or a qualified workshop.
This value may vary following a change in the style of driving or the relief, resulting in a significant change in the current fuel consumption.
Trip computer, a few definitions…

Range
(miles or km)
This indicates the distance
which can still be travelled with
the fuel remaining in the tank
in relation to the average fuelconsumption over the last few
miles (kilometres) travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
This function is only displayed from20 mph (30 km/h).
Current fuel consumption
(mpg or l/100 km or km/l)This is the average fuel consumption
during the last few seconds.

Average fuel consumption
(mpg or l/100 km or km/l)
This is the average fuel
consumption since the last tripcomputer zero reset.
Average speed
(mph or km/h)
This is the average speed calculated
since the last trip computer zero reset
(ignition on).

Reset history
)With trip 2 displayed, press the button (on
the end of the wiper stalk) for more than
two seconds to reset the history to zero.

Trips
"1"
and "2"are independent but their use
is identical.
For example, trip "1"
can be used for daily figures, and trip "2"
for monthly figures.

01 FIRST STEPS
Short press: select a preset
radio station.
Long press: store thecurrent radio station.
TA
(Traffi c
Announcement) function On / Off. Displa
y the list of radio stations received, CD/MP3/Apple®
player tracks or folders.®

Long press: management of the classifi cation of MP3/WMA fi les/update the list of stations received.

A
ccess to "Audio
settings ": musical
ambiences, bass, treble,
loudness, distribution, left/right balance, front/rear fader, automatic volume
adjustment.
Select the FM waveband(AM not available on Hybrid vehicles).

Press and hold: reinitialisethe system.

Select the source: CD,USB, AUX, Apple®player,
Bluetooth Streaming, Radio.
Abandon the current
operation, go up one level.
Lon
g press: return topermanent display.
On / Off.
MOD
Ebutton: select the type
of permanent display.

Rotation: ad
just volume(each source is independent,
including TA messages and navigation instructions).
Select:
- the previous/next line in a list or menu.
- the previous next media
folder.
- step by step previous
/next radio frequency.
- previous
/next MP3 folder.
Move u
p/down, in "Move the map
" mode.
Select:
- automaticall
y the previous/next radio frequency.
- the previous
/next CD, MP3 or media track.
Move le
ft/right, in "Move the map
" mode.
Display black screen.

Short press: mute /
r
estore sound.

SRC

02


-
+
STEERING MOUNTED CONTROLS


- Rotation
R
adio -automatic selection of next /
previous frequency.
Media: previous
/ next track.

- Press then rotation: access to
6 preset stations.


-
Change the audio source.


- TEL button
(short press):
Accept an incomin
g call
Call in pro
gress: access to telephone
menu: hang up, secret mode, hands-free
mode.


- TEL button
(long press):
Reject an incoming call or end a call in
progress.
When not makin
g a call, access to the
telephone menu (Dial, Contacts, Calls log,
Voice mailbox).


- In
crease volume.

- D
ecrease volume.


- Radio: displa
y the list of stations.
Media: displa
y the list of tracks.

08
295
RADIO
By alphabetical list
Pr
ess RADIOor LIST , select the station
of your choice and confi rm.
B
y automatic frequency search
Press or for the automatic searchfor a lower or higher radio frequency.
Or turn the thumb wheel at the steeringmounted controls.
B
y manual frequency search
Pr
ess or to adjust the radiofrequency step by step.
Pr
ess the button on the numerical keypad to recall a preset station.

Or press then turn the thumb wheel at
the steering mounted controls.








SELECTING A STATION


The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode. This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audiosystem.


PRESETTING A STATION


After selecting a station, press one of
the buttons on the numerical keypad for 2 seconds to preset the current station.
An audible si
gnal confi rms that thestation has been preset. The qualit
y of reception is represented by the number of active waves in this symbol.