engine oil CITROEN JUMPY 2022 Owners Manual
Page 9 of 324
7
Eco-driving
Eco-driving
Eco-driving refers to a range of everyday 
practices that allow the motorist to optimise 
the vehicle's energy consumption (fuel and/or 
electricity) and CO
2 emissions.
Optimise your use of the gearbox
With a manual gearbox, move off gently and 
change up promptly. While accelerating, change 
up early.
With an automatic gearbox, favour automatic 
mode. Do not depress the accelerator pedal 
heavily or suddenly.
The gear shift indicator prompts you to engage 
the most suitable gear. Whenever this indication 
is displayed on the instrument panel, follow it 
straight away.
With an automatic gearbox, this indicator 
appears only in manual mode.
Drive smoothly
Maintain a safe distance between vehicles, use 
engine braking rather than the brake pedal and 
press the accelerator gradually. These practices 
help to save on energy consumption, reduce 
CO
2 emissions and decrease general traffic 
noise.
When the traffic is flowing smoothly, select the 
cruise control.
Control the use of electrical equipment
Before moving off, if the passenger compartment 
is too warm, ventilate it by opening the windows 
and air vents before using the air conditioning.
At speeds above 31
  mph (50   km/h), close the 
windows and leave the air vents open.
Consider using equipment that can help keep 
the temperature in the passenger compartment 
down (e.g.
  sunroof blind, window blinds).
Unless automatically regulated, switch off the air 
conditioning as soon as the desired temperature 
has been reached.
Switch off the demisting and defrosting functions, 
if they are not managed automatically.
Switch off the heated seat as soon as possible.
Adapt your use of the headlamps and/or 
foglamps to the level of visibility, in accordance 
with current legislation in the country in which 
you are driving.
Avoid running the engine before moving off, 
particularly in winter (other than in severe wintry 
conditions: temperature below -23°C). The 
vehicle will warm up much faster while driving.
As a passenger, avoid connecting your 
multimedia devices (e.g.
  film, music, video 
game) to help reduce the consumption of energy.
Disconnect all portable devices before leaving 
the vehicle.
Limit the causes of excess consumption
Spread loads throughout the vehicle. Place the 
heaviest items in the boot as close as possible to 
the rear seats. Limit the loads carried in the vehicle and 
minimise wind resistance (e.g.
  roof bars, roof 
rack, bicycle carrier, trailer). Preferably, use a 
roof box.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and refit 
summer tyres.
Comply with the servicing instructions
Check tyre pressures regularly, with the tyres 
cold, referring to the label in the door aperture on 
the driver's side.
Carry out this check in particular:
–
 
before a long journey
 .
–
 
at each change of season.
–
 
after a long period out of use.
Do not forget the spare wheel and, where 
applicable, the tyres on your trailer or caravan.
Have your vehicle serviced regularly (e.g.
  engine 
oil, oil filter, air filter, passenger compartment 
filter, etc.). Observe the schedule of operations in 
the manufacturer's service schedule.
With a BlueHDi Diesel engine, if the SCR system 
has a fault, your vehicle will emit pollution. Visit 
a CITROËN dealer or a qualified workshop 
as soon as possible to restore your vehicle's 
nitrogen oxide emissions to legal levels.
When filling the fuel tank, do not continue after 
the third cut-out of the nozzle, to avoid overflow.
You will only see the fuel consumption of your 
new vehicle settle down to a consistent average 
after the first 1,900 miles (3,000 kilometres).   
Page 12 of 324
10
Dashboard instruments
1.Cruise control or speed limiter settings
Display of speed limit signs
2. Gear shift indicator (Diesel)
Gear with an automatic gearbox (Diesel) or 
Drive selector position (Electric)
3. Digital speedometer (mph or km/h) with LCD 
and LCD text instrument panel (Diesel)
Display area with matrix instrument panel: 
alert or function status message, trip 
computer, digital speedometer (mph or km/h), 
power flow/vehicle charge state (Electric), 
etc.
4. Service indicator, then total distance recorder 
(miles or km)
Trip distance recorder (miles or km) (Diesel)
Remaining range/Driving mode selected 
(Electric)
Display area with LCD text instrument 
panel: alert or function status message, trip 
computer, etc.
5. Engine coolant temperature gauge
6. Engine oil level indicator
7. Fuel gauge
Control buttons 
 
With LCD display    
 
With LCD text display 
 
With matrix display 
 
With matrix display (Electric) 
 
A.
Resetting the service indicator.
Temporary reminder of servicing information.
Reminder of driving range with the AdBlue
® 
system.
Depending on version: go back up a level or 
cancel the current operation.
B. General lighting dimmer.
Depending on version: browse a menu or list, 
or change a value.
C. Resetting the trip distance recorder.
Depending on version: enter the configuration 
menu (long press), confirm a choice (short 
press).
D.Reminder of servicing information or driving 
range with the SCR system and the
 AdBlue®.
Resetting the selected function (service 
indicator or trip distance recorder).
Depending on version: enter the configuration 
menu (long press), confirm a choice (short 
press).
With the touch screen, it is also possible 
to adjust the lighting dimmer.
Rev counter 
 
Rev counter (x 1000 rpm).
Power indicator (Electric) 
 
Power indicator  CHARGE, ECO, POWER or 
NEUTRAL.
For more information on the Indicators , 
please refer to the corresponding 
section.    
Page 13 of 324
11
Dashboard instruments
1Warning and indicator 
lamps
Displayed as symbols, the warning and indicator 
lamps inform the driver of the occurrence of a 
malfunction (warning lamps) or of the operating 
status of a system (operation or deactivation 
indicator lamps). Certain lamps light up in two 
ways (fixed or flashing) and/or in several colours.
Associated warnings
The illumination of a lamp may be accompanied 
by an audible signal and/or a message displayed 
in a screen.
Relating the type of alert to the operating status 
of the vehicle allows you to determine whether 
the situation is normal or whether a fault has 
occurred: refer to the description of each lamp 
for further information.
When the ignition is switched on
Certain red or orange warning lamps come on 
for a few seconds when the ignition is switched 
on. These warning lamps should go off as soon 
as the engine is started.
For more information on a system or a function, 
refer to the corresponding section.
Persistent warning lamp
If a red or orange warning lamp comes on, there 
may be fault which needs further investigation.
If a lamp remains lit
The references (1), (2) and (3) in the warning 
and indicator lamp description indicate whether 
you should contact a qualified professional in 
addition to the immediate recommended actions.
(1): You must stop the vehicle.
Stop as soon as it is safe to do so and switch off 
the ignition.
(2): Contact a CITROËN dealer or a qualified 
workshop.
(3): Visit a CITROËN dealer or a qualified 
workshop.
List of warning and 
indicator lamps
Red warning/indicator lamps
STOP
Fixed, associated with another warning 
lamp, accompanied by the display of a 
message and an audible signal.
A serious fault with the engine, braking system, 
power steering or automatic gearbox or a major 
electrical fault has been detected.
Carry out (1) and then (2).
Maximum engine coolant temperatureFixed (warning lamp or LED), with 
the needle in the red zone 
(depending on version).
The temperature of the cooling system is too 
high. Carry out (1), then wait until the engine has 
cooled down before topping up the level, if 
necessary (Diesel). If the problem persists, carry 
out (2).
Engine oil pressureFixed.
There is a fault with the engine lubrication 
system.
Carry out (1) and then (2).
System malfunction (Electric)Fixed.
A fault involving the electric motor or 
traction battery has been detected.
Carry out (1) and then (2).
Cable connected (Electric)Fixed when the ignition is switched on.
The charging cable is connected to the 
vehicle's connector.
Fixed when the ignition is switched on, 
accompanied by a message.
It is not possible to start the vehicle while the 
charging cable is connected to the vehicle’s 
connector.
Disconnect the charging cable and close the 
flap.
Battery chargeFixed.
The battery charging circuit has a fault 
(dirty terminals, slack or cut alternator belt, etc.).
Clean and retighten the lugs. If the warning lamp 
does not go off when the engine is started, carry 
out (2).    
Page 20 of 324
18
Dashboard instruments
Checking
After driving for a few minutes, the temperature 
and pressure in the cooling system increase.
To top up the level:
► 
wait at least one hour for the engine to cool,
►
 
unscrew the cap by two turns to allow the 
pressure to drop,
►
 
when the pressure has dropped, remove the 
cap,
►
 
top up the level to the "MAX" mark.
For more information on  Checking levels
, refer 
to the corresponding section.
Be aware of the risk of scalding when 
topping up the coolant. Do not fill above 
the maximum level (indicated on the 
reservoir).
Engine oil level indicator
(Depending on version)
On versions fitted with an electric gauge, the 
engine oil level status is displayed on the 
instrument panel for a few seconds when the 
ignition is switched on, at the same time as the 
servicing information.
The level read will only be correct if the  vehicle is on level ground and the engine 
has been off for more than 30 minutes.
Oil level correct 
 
This is indicated by a message on the instrument 
panel.
Low oil level 
 
This is indicated by a message on the instrument 
panel.
If a low oil level is confirmed by a check using 
the dipstick, the level must be topped up to avoid 
damage to the engine.
For more information on  Checking levels, refer 
to the corresponding section.
Oil gauge malfunction 
 
This is indicated by the display of a message on 
the instrument panel.
Contact a CITROËN dealer or a qualified 
workshop.
In the event of a malfunction of the 
electric gauge, the oil level is no longer 
monitored.
If the system is faulty, you must check the 
engine oil level using the manual dipstick 
located in the engine compartment.
For more information on  Checking levels, 
refer to the corresponding section.
AdBlue® range indicators 
(BlueHDi)
The Diesel BlueHDi engines are equipped with 
a system that associates the SCR (Selective 
Catalytic Reduction) emissions control system 
and the Diesel particle filter (DPF) for the 
treatment of exhaust gases. They cannot 
function  without AdBlue
® fluid.
When the level of AdBlue® falls below the 
reserve level (between 1,500 and 0 miles (2,400 
and 0
 
km)), a warning lamp lights up when 
the ignition is switched on and an estimate 
of the distance that can be travelled before 
engine starting is prevented is displayed in the 
instrument panel.
The engine starting prevention system  required by regulations is activated 
automatically once the AdBlue
® tank is empty. 
It is then no longer possible to start the 
engine until the minimum level of AdBlue
® has 
been topped up.    
Page 102 of 324
100
Safety
reduction in the resistance of the pedal and an 
increase in braking efficiency.
Anti-slip regulation (ASR)/Dynamic stability control 
(DSC)
Anti-slip regulation (or traction control) optimises 
traction by using engine braking and by applying 
the brakes on the driving wheels to avoid one 
or more wheels spinning. It also enhances the 
vehicle's directional stability.
If there is a difference between the vehicle’s 
trajectory and the path desired by the driver, the 
dynamic stability control system automatically 
uses engine braking and the brakes on one or 
more wheels to return the vehicle to the desired 
path, within the limits of the laws of physics.
These systems are activated automatically every 
time the vehicle is started.
These systems are activated in the event of a problem with grip or trajectory 
(confirmed by this warning lamp flashing on the 
instrument panel).
Deactivation/Reactivation
In exceptional conditions (moving a vehicle that 
is bogged down in mud, stuck in snow, on loose 
soil, etc.), it may prove useful to deactivate the 
DSC/ASR systems, so that the wheels can move 
freely and regain grip.
However, it is recommended that the systems be 
reactivated as soon as possible.
Only the ASR system can be deactivated 
from the touch screen.
Deactivating using the button or Advanced 
Grip Control
Press this button or turn the thumbwheel 
to this position.
The indicator lamp in the button or thumbwheel 
comes on: the DSC/ASR systems no longer 
have an effect on engine operation.
Deactivating using the touch screen
In the "Driving/Vehicle" menu, deactivate 
the ASR  system.
A confirmation message is displayed and  this warning lamp on the instrument panel 
comes on.
The ASR system no longer acts on the operation 
of the engine.
Reactivating using the button or Advanced 
Grip Control
Press this button.  
Or
Turn the thumbwheel to this position. 
The indicator lamp in the button or thumbwheel 
goes off.
Reactivating using the touch screen
In the "Driving/Vehicle" menu, activate 
the ASR  system.
A confirmation message is displayed and  this warning lamp on the instrument panel 
goes off.
These systems are reactivated automatically 
every time the ignition is switched off, or at 
speeds over 31 mph (50
  km/h).
Below 31 mph (50
  km/h), these systems must be 
reactivated manually.
Malfunction
In the event of a malfunction, this warning 
lamp lights up on the instrument panel, 
accompanied by the display of a message and 
an audible signal.
Have it checked by a CITROËN dealer or a 
qualified workshop.
ASR/DSC
These systems enhance safety during 
normal driving, but should not encourage 
the driver to take extra risks or drive at high 
speed.
It is in conditions of reduced grip (rain, snow, 
ice) that the risk of loss of grip increases. It 
is therefore important for your safety to keep 
these systems activated in all conditions, and 
particularly in difficult conditions.
Correct operation of these systems depends 
on compliance with the manufacturer's 
recommendations relating to the wheels 
(tyres and rims), braking and electronic 
components, as well as the assembly and 
repair procedures provided by CITROËN 
dealers.
In order to ensure that these systems remain 
effective in wintry conditions, the use of snow    
Page 179 of 324
 
 
177
Practical information
7
 
FILL UP WITH  
CONFIDENCE
 
WITH QUARTZ LUBRICA\BNT\f
* 1L & 5L produced in Europe
Part\bers  for  more  tha\b  50  years,  Citroën  & 
TotalEnergies share \fommon values\b te\fhnology, 
\freativity, innovation. TotalEnergies equips Citroën 
vehi\fles with  Quartz lubrica\bts from their first filling 
in the fa\ftory to approved maintenan\fe networks to 
guarantee them optimal performan\fe on a daily basis. 
Espe\fially  designed  for  Citroën  vehi\fles,  Quartz 
lubri\fants make them even more powerful, more fuel 
effi\fient and more environmentally friendly. For your 
\far maintenan\fe, fill up with \fonfiden\fe with Quartz 
lubri\fants !Keep your e\bgi\be you\B\bger for lo\bger !
Quartz  I\beo  Xtra  First  0W-20  is  a  very  high 
performan\fe lubri\fant resulting from the joint work of 
the Citroën and TotalEnergies R&D teams. Its innovative 
te\fhnology extends your engine’s life while rea\fhing 
signifi\fant fuel savings and thus limiting CO
2 emissions. 
The produ\ft is now available in new pa\fkaging* made 
of 50% re\fy\fled mate\hrial and 100% re\fy\fl\hable.
 
Compatibility of fuels  
Diesel fuels conforming to the EN590, EN16734 
and EN16709 standards and containing up to 
7%, 10%, 20% and 30% fatty acid methyl ester 
respectively. The use of B20 or B30 fuels, even 
occasionally, imposes special maintenance 
conditions referred to as "Arduous conditions".
  
Paraffinic Diesel fuel conforming to the EN15940 
standard.
The use of any other type of (bio) fuel 
(e.g.   pure or diluted vegetable or animal 
oils, domestic fuel) is strictly prohibited - risk 
of damaging the engine and fuel system!
The only Diesel fuel additives authorised  for use are those that meet the B715000 
standard.
Diesel at low temperature
At temperatures below 0 °C (+32 °F), the 
formation of paraffins in summer-type Diesel 
fuels could prevent the engine from operating 
correctly
. In these temperature conditions, use 
winter-type Diesel fuel and keep the fuel tank 
more than 50
  % full.
At temperatures below -15 °C (+5 °F) to avoid 
problems starting, it is best to park the vehicle 
under shelter (heated garage).
Travelling abroad
Certain fuels could damage your vehicle’s 
engine.
In certain countries, the use of a particular 
fuel may be required (specific octane rating, 
specific trade name, etc.) to ensure correct 
operation of the engine.
For all additional information, consult a dealer.
Refuelling
Fuel tank capacity: approximately 69 litres.
Reserve level: approximately 6 litres.
Low fuel level
When the low fuel level is reached, 
one of these warning lamps lights 
up on the instrument panel, accompanied by the 
display of a message and an audible signal. 
When it first comes on, about 8 litres of fuel 
remain.
You must refuel as soon as possible to avoid 
running out of fuel.
For more information on  Running out of fuel 
(Diesel), refer to the corresponding section.
A small arrow by the warning lamp  indicates which side of the vehicle the 
fuel filler flap is located on.
Stop & Start
Never refuel with the engine in STOP 
mode; you must switch off the ignition.
Refuelling
At least 8 litres of fuel must be added, in order to 
be registered by the fuel gauge.
Opening the filler cap may create a noise caused 
by an inrush of air. This is entirely normal and 
results from the sealing of the fuel system.
To refuel in complete safety:
►
 
Always switch off the engine.
►
 
Unlock the vehicle using the Keyless Entry 
and Start.
 
 
► Open the fuel filler flap.    
Page 195 of 324
193
Practical information
7or in certain moving components - risk of 
strangulation and serious injury!
Electric motor
Take care with objects or clothing that 
could be caught in the blades of the cooling 
fan or in certain moving components - risk of 
strangulation and serious injury!
Before carrying out any work under the 
bonnet, you must switch off the ignition, check 
that the READY indicator lamp is off on the 
instrument panel and disconnect the nozzle 
from the charging connector if it is connected.
The location of the interior bonnet  release lever prevents the bonnet being 
opened when the left-hand front door is 
closed.
When the engine is hot, handle the 
exterior safety catch and the bonnet stay 
with care (risk of burns), using the protected 
area.
When the bonnet is open, take care not to 
damage the safety catch.
Do not open the bonnet under very windy 
conditions.
Cooling of the engine when stopped
The engine cooling fan may start after 
the engine has been switched off.
Take care with objects or clothing that 
could be caught in the blades of the fan!
Opening
► Open the door . 
 
► Pull the release lever  1 , located at the bottom 
of the door frame, towards you.
►
 
T
 ilt the safety catch 2 upwards, then raise the 
bonnet.
►
 
Unclip the stay 
 3 from its housing and place it 
in the support slot to hold the bonnet open.
Closing
► Hold the bonnet and  pull out the stay from the 
support slot.
►
 
Clip the stay in its housing.
►
 
Lower the bonnet and release it near the end 
of its travel.
►
 
Pull on the bonnet to check that it is locked 
correctly
.
Because of the presence of electrical 
equipment under the bonnet, it is strongly 
recommended that exposure to water (rain, 
washing, etc.) be limited. 
Engine compartment
The engine shown here is an example for 
illustrative purposes only.
The locations of the following components may 
vary:
–
 
Air filter
 .
–
 
Engine oil dipstick.
–
 
Engine oil filler cap.
–
 
Priming pump.   
Page 196 of 324
194
Practical information
Diesel engine 
 
1.Screenwash fluid reservoir
2. Engine coolant reservoir
3. Brake fluid reservoir
4. Battery
5. Remote earth point (-)
6. Fusebox
7. Air filter
8. Engine oil filler cap
9. Engine oil dipstick
10. Priming pump*
11 . Power steering fluid reservoir
Diesel fuel system
This system is under very high pressure.
All work must be carried out only by a 
CITROËN dealer or a qualified workshop
* Depending on engine.
Electric motor 
 
1. Screenwash fluid reservoir
2. Engine coolant reservoir (level only)
3. Brake fluid reservoir
4. Battery/Fuses
5. Remote earth point (-)
6. Fusebox
7. 400
  V electrical circuit
8. Emergency circuit-breaker for emergency 
services and maintenance technicians
9. Power steering fluid reservoir
For more information on the  Charging system 
(Electric), refer to the corresponding section.
Checking levels
Check all of the following levels regularly in 
accordance with the manufacturer's service 
schedule. Top them up if required, unless 
otherwise indicated.
If a level drops significantly, have the 
corresponding system checked by a CITROËN 
dealer or a qualified workshop.
The fluids must comply with the  manufacturer's requirements and with 
the vehicle's engine.
Take care when working under the  bonnet, as certain areas of the engine 
may be extremely hot (risk of burns) and the 
cooling fan could start at any time (even with 
the ignition off).
Used products
Avoid prolonged contact of used oil or  fluids with the skin.
Most of these fluids are harmful to health and 
very corrosive.
Do not discard used oil or fluids into 
sewers or onto the ground.
Empty used oil into the containers reserved 
for this purpose at a CITROËN dealer or a 
qualified workshop.
Engine oil
The level is checked, with the engine  having been switched off for at least 30 
minutes and on level ground, either using the oil 
level indicator in the instrument panel when the    
Page 197 of 324
195
Practical information
7ignition is switched on (for vehicles equipped 
with an electric gauge), or using the dipstick.
It is normal to top up the oil level between two 
services (or oil changes). It is recommended 
that you check the level, and top up if necessary, 
every 3,000 miles (5,000 km).
In order to maintain the reliability of the 
engine and emissions control system, 
never use additives in the engine oil.
Checking using the dipstick
For the location of the dipstick, please refer 
to the illustration of the corresponding engine 
compartment.
►
 
Grasp the dipstick by its coloured grip and 
pull it out completely
.
►
 
Wipe the end of the dipstick using a clean, 
lint-free cloth.
 
 
► Reinsert the dipstick and push fully down, 
then pull it out again to visually check the oil 
level: the correct level is between marks
 
A
  (max) 
and
  B (min).
Do not start the engine if the level is:
–
 
above mark
   A: contact a CITROËN dealer or a 
qualified workshop.
– below mark  B : top up the engine oil 
immediately.
Oil grade
Before topping up or changing the 
engine oil, check that the oil is suitable 
for your engine and complies with the 
recommendations in the service schedule 
supplied with the vehicle (or available from 
your CITROËN dealer or qualified workshop).
Use of non-recommended oil may invalidate 
your warranty in the event of engine failure.
Topping up the engine oil level
For the location of the engine oil filler cap, please 
refer to the corresponding engine compartment 
illustration.
►
 
Add oil in small quantities, avoiding any spills 
on engine components (risk of fire).
►
 
W
 ait a few minutes before checking the level 
again using the dipstick.
►
 
T
 op up the level if necessary.
►
 
After checking the level, carefully screw the 
oil filler cap back on
  and replace the dipstick in 
its tube.
The oil level indication displayed on the  instrument panel when the ignition is 
switched on is not valid for 30 minutes 
following an addition of oil. 
Brake fluid
The level of this fluid should be  close to 
the "MAX" mark. If not, check the brake 
pads for wear.
To know how often the brake fluid should be 
replaced, refer to the manufacturer's servicing 
schedule.
Clean the cap before removing it to refill. 
Use only DOT4 brake fluid from a sealed 
container.
Power steering fluid
The level of this fluid should be close to  the "MAX" mark. Check it, with the 
vehicle parked on level ground and with the 
engine cold, by reading the level on the filler 
neck.
Engine coolant
(Diesel)
It is normal to top up this fluid between 
two services.
The check and top-up must only be done with 
the engine cold.
A level of coolant that is too low risks causing 
major damage to the engine; the coolant level 
must be close to the "MAX" mark without ever 
going above it.
If the level is close to or below the " MIN" mark, it 
is essential to top it up.   
Page 199 of 324
197
Practical information
7Versions equipped with Stop & Start are 
fitted with a 12  V lead-acid battery with 
special technology and specifications.
Its replacement should be carried out only by 
a CITROËN dealer or a qualified workshop.
Passenger compartment 
filter
Depending on the environment and the 
use of the vehicle (e.g. dusty atmosphere, 
city driving), change it twice as often, if 
necessary .
A clogged passenger compartment filter 
can adversely affect air conditioning 
system performance and generate 
undesirable odours.
Air filter
Depending on the environment and the 
use of the vehicle (e.g. dusty atmosphere, 
city driving), change it twice as often, if 
necessary .
Oil filter
Change the oil filter each time the engine 
oil is changed.
Particle filter (Diesel)
 / The start of clogging of the 
particle filter is indicated by the 
temporary lighting of this warning lamp, 
accompanied by an alert message.
As soon as traffic conditions allow, regenerate 
the filter by driving at a speed of at least 37
  mph 
(60
  km/h), with an engine speed above 2,500 
rpm, for about 15 minutes (until the warning lamp 
goes out).
If it is not possible to reach 37
  mph (60   km/h), 
leave the engine running at idle for about 15 
minutes, then drive with an engine speed
  above 
2,500 rpm for 15 minutes.
Do not switch off the engine until the filter 
is fully regenerated; repeated intervals 
can degrade the engine oil prematurely.
Regenerating the filter while the vehicle is 
stationary is not recommended.
Following prolonged operation of the 
vehicle at very low speed or at idle, you 
may, in exceptional circumstances, notice 
water vapour coming from the exhaust while 
accelerating. These emissions have no 
impact on the vehicle’s behaviour and the 
environment.
New vehicle
During the first few particle filter 
regeneration operations, you may notice a 
"burning" smell. This is perfectly normal.
Manual gearbox
The gearbox does not require any  maintenance (no oil change).
Automatic gearbox
The gearbox does not require any maintenance (no oil change).
Drive selector
The drive selector does not require any maintenance.
Manual parking brake
If you notice excessive brake lever travel 
or decreased effectiveness, the parking 
brake must be adjusted, even between two 
services.
This system must be checked by a CITROËN 
dealer or a qualified workshop.
Electric parking brake
This system does not require any routine  servicing. However, in the event of a 
problem, do not hesitate to have the system 
checked by a CITROËN dealer or a qualified 
workshop.
For more information on the  Electric 
parking brake, refer to the 
corresponding section.