lock Citroen XSARA PICASSO 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine XSARA 2, all types
Operation to reconnect the battery after a vehicle repair
WARNING
If the battery has been disconnected, after reconnecting it is ESSENTIALto wait 1 minutebefore switching on the ignition,
otherwise the engine ECU will lock up.
If the ECU has locked up :
Switch off the ignition.
Wait
1 minute.
Switch the ignition back on, the ECU is unlocked.

Downloaded from www.Manualslib.com manuals search engine OPERATIONS TO BE CARRIED ORT AFTER A REPAIR
C2 C3
4
GENERAL
IMPERATIVE:All these operations are to be performed following a reconnection of the battery.
Antiscanning function.
It is necessary to wait 1 minute after the battery has been disconnected in order to be able to start the vehicle.
Tailgate.The opening of the tailgate is deactivated on reconnection of the battery.
Perform locking/unlocking to activate the opening of the tailgate.
Overspeed check.The vehicle’s overspeed values have to be reinitialised.
The button on the wiper stalk (multifunction display B or C)or the button on the dashboard (multifunction display A or clock)operates the following
functions:
Activation of the vehicle’s overspeed function.
Programming of the overspeed alert.
Electric windows.It may be necessary to reinitialise the sequential and antipinch functions.
NOTE:If the window is open at the time the battery is reconnected, action the window switch several times to close it, then reinitialise.
Open the window fully.
Action and release the window switch until the window is complandely closed.
This operation has to be carried ort on each electric window.

Downloaded from www.Manualslib.com manuals search engine 68
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
EnginesHFX KFV NFU
Crankshaft
Accessories drive pulley2,5 ± 0,2
Pinion fixing on crankshaft
Tightening4 ± 0,4
Angular tightening45° ± 4°
Cylinder block
Sump0,8 ± 0,2
Timing belt tensioner roller2,1 ± 0,2
Accessories belt guide roller2,5 ± 0,2
Alternator support2,5 ±0,2
Alternator TU1JPTU3JP
Pretightening
1 ±
Tightening3,7 ± 0,3
Alternator TU5JP4
Pretightening
1 ±
Tightening4 ±,04
Aircon compressor support 2,2 ± 0,2
Aircon compressor2,3 ± 0,2
C2

Downloaded from www.Manualslib.com manuals search engine 72
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engine8HX
Crankshaft
Bearing cap fixing screws
Pretightening
1 ± 0,2
Slackening180°
Tightening3 ± 0,3
Angular tightening140°
Con rod screws
Tightening
1 ± 0,1
Angular tightening100° ± 5°
3 ± 0,3
Angular tightening180° ± 5°
Cylinder block
Sump1,3 ±0,1
Timing belt guide roller2,3 ± 0,2
Timing belt tensioner roller3,7 ± 0,3
C2

Downloaded from www.Manualslib.com manuals search engine 74
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engine8HX
Lubrication circuit
Oil pump assembly
Pretightening
0,5 ± 0,1
Tightening0,9 ± 0,1
Coolant/oil heat exchanger1 ± 0,1
Diesel injection circuit
Sphericalbase screws for diesel injection fixing fork2,5 ± 0,2
Fuel high pressure common injection rail on engine block2,2 ± 0,2
Unions on fuel high pressure common injection rail2,5 ± 0,2
Diesel injection pump on support2,2 ± 0,2
Union on diesel injection2,5 ±0,2
Diesel injection pump pulley5 ± 0,5
Union on diesel high pressure pump2,5 ± 0,2
Cooling circuit
Coolant pump
Pretightening
0,3 ±0,1
Tightening0,9 ± 0,1
Coolant outlet housing
Pretightening
0,3 ±0,1
Tightening0,7 ± 0,1
C2

Downloaded from www.Manualslib.com manuals search engine 76
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Crankshaft
Engine types HFX KFV NFU
Accessories drive pulley0,8 ± 0,2
Pinion fixing on crankshaft10 ± 1 2,5 ± 0,2
Cylinder block
Sump0,8 ± 0,2
Timing belt tensioner roller2 ± 0,2 2,2 ± 0,2
Accessories belt tensioner roller2 ± 0,2 2,5 ± 0,2
Alternator support fixing1,7 ±0,3
Alternator fixing on support3,7 ± 0,3
Cylinder head
Coolant outlet housing0,8 ± 0,2
Camshaft bearing cap
Tightening
2 ± 0,2 2 ± 0,2
Angular tightening44°±4°50° ± 5°
0,8 ± 0,2
Exhaust manifold1,7 ± 0,3 2 ± 0,2
Valve rockers adjusting screw1,75 ±0,25
Sparking plugs2,75 ± 0,25
Camshaft pulley screw8 ± 0,8
C3

Downloaded from www.Manualslib.com manuals search engine 79
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
EngineKFU
Crankshaft
Accessories drive pulley0,8 ± 0,2
Pinion fixing on crankshaft
Pretightening
4 ± 0,4
Angular tightening45 ± 4°
Cylinder block
Sump0,8 ± 0,2
Accessories belt guide roller4 ± 0,4
Timing belt tensioner roller2,1 ± 0,2
Accessories belt tensioner roller2,5 ± 0,2
Alternator support2,5 ± 0,3
Crankshaft bearing caps
Tightening
2 ±0,3
Angular tightening44°(reused screws cleaned and greased)
Cylinder head
Coolant outlet housing0,8 ± 0,2
Camshaft bearing caps1 ± 0,2
Camshaft bearing cap covers0,9 ± 0,1
Inlet manifold0,8 ± 0,2
C3

Downloaded from www.Manualslib.com manuals search engine 83
ENGINE
83
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines 8HX 8HW 8HZ
Crankshaft
Bearing cap fixing screw
Pretightening1
SlackeningYES
Tightening3
Angular tightening140°
Con rod nuts
Pretightening1
SlackeningYES
Tightening1,5 ± 0,1
Angular tightening100°±5°
Accessories drive pulley
Pretightening3 ±0,4
Angular tightening180°±5°
Cylinder block
Sump1 ± 0,1
Timing belt guide roller 4,5 ± 0,4 3,7 ± 0,4Timing belt tensioner roller3 ± 0,3 2,3 ± 0,3
C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 85
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines8HX 8HW 8HZ
Diesel injection circuit
Sphericalbase screws for diesel injection fixing fork 0,3 ± 0,1Fuel high pressure common injection rail on engine block 2 ± 0,2
Unions on fuel high pressure common injection rail
Pretightening1,7± 0,2
Tightening2,25 ± 0,2
Diesel injection pump on support
Union on diesel injection 2,25 ± 0,2
Diesel injection pump pulley 5 ± 0,5
Union on diesel high pressure pump2,25 ±0,2
Cooling circuit
Coolant pump
Pretightening0,3 ± 0,06
Tightening1 ± 0,1
Coolant outlet housing
Pretightening0,3 ± 0,06
Tightening0,7 ±0,08
C3 C3 PLURIEL XSARA

Downloaded from www.Manualslib.com manuals search engine 87
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Engines8HV 8HY
Crankshaft
Bearing cap fixing screw
Tightening3 ± 0,3
Angular tightening140° ± 1°,4’
Crankshaft pullet hub
Angular tightening180°±5°
Cylinder block
Oil sump1 ±0,1
Timing belt tensioner roller 4 ± 0,4
Timing belt guide roller
2,5 ±0,2
Timing belt guide roller support
Cylinder head
Camshaft bearing cap cover
1 ±0,1
Inlet manifold
Exhaust manifold2,5 ± 0,2
Cylinder head cover Screws (M6) to 1 ± 0,2
Camshaft pinion4,3 ± 0,4
Fuel high pressure pump pinion 5 ± 0,5
C3