towing DACIA DUSTER 2009 1.G Heating And Air Conditioning Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 62A-10
AIR CONDITIONING
Condenser: Removal - Refitting
AIR CONDITIONING
62A
Location and specifications (tightening torques, parts
always to be replaced, etc.) (see 62A, Air condition-
ing, Air conditioning: List and location of compo-
nents, page 62A-1) .
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the coolant circuit using the refrigerant
charging station.
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
aRemove the front bumper (see Front bumper as-
sembly: Exploded view) and (see Exterior body
front trim assembly: Exploded view) (55A, Exteri-
or protection).aRemove:
-the air deflector mountings (1) ,
-the air deflector (2) .
aRemove the intercooler (see ) (12B, Turbocharging).
II - REMOVAL OPERATION
aRemove the bolts from the pipes on the condenser
(see 62A, Air conditioning, Air conditioning: List
and location of components, page 62A-1) .
aDisconnect the pipes from the condenser (see 62A,
Air conditioning, Air conditioning: List and loca-
tion of components, page 62A-1) .
aFit blanking plugs on the pipe openings.
aRemove (see 62A, Air conditioning, Air conditio-
ning: List and location of components, page
62A-1) :
-the condenser bolts,
-the condenser. Equipment required
refrigerant charging station
IMPORTANT
To avoid all risk of damage to the systems, apply
the safety and cleanliness instructions and opera-
tion recommendations before carrying out any
repair (see Air conditioning: Precautions for the
repair) .
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
145079
K9K
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.

Downloaded from www.Manualslib.com manuals search engine 62A-12
AIR CONDITIONING
Compressor: Removal - Refitting
AIR CONDITIONING
62A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
aDrain the coolant circuit using the refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) .
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).aRemove:
-the front bumper (see Front bumper: Removal -
Refitting) and (see Exterior body front trim as-
sembly: Exploded view) (55A, Exterior protec-
tion),
-the front right-hand wheel (see Wheel: Removal -
Refitting) (35A, Wheels and tyres),
-the accessories belt (see Accessories belt: Re-
moval - Refitting) (11A, Top and front of engine).
II - REMOVAL OPERATION
aRemove:
-the pipe retaining bracket bolt (1) on the compres-
sor,
-the pipe union bolts (2) on the compressor. Equipment required
refrigerant charging station
Tightening torquesm
compressor bolts21 N.m
pipe union bolts8 N.m
pipe retaining bracket
bolt on the compressor21 N.m
IMPORTANT
Consult the safety instructions and cleanliness
advice and the operation recommendations before
carrying out any repairs (see Air conditioning:
Precautions for repair).
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
K4M
145190

Downloaded from www.Manualslib.com manuals search engine 62A-21
AIR CONDITIONING
Refrigerant circuit pipe: Removal - Refitting
AIR CONDITIONING
62A
Location and specifications (tightening torques, parts
always to be replaced, etc.) (see 62A, Air condition-
ing, Air conditioning: List and location of compo-
nents, page 62A-1) .
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
Drain the coolant circuit using the refrigerant
charging station (see Refrigerant circuit: Drain-
ing - Filling) .
aDisconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
For the pipe between the expansion valve and the
condenser:
aPosition the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).aRemove:
-the front bumper (see Exterior body front trim as-
sembly: Exploded view) and (see Exterior body
front trim assembly: Exploded view) (55A, Exte-
rior protection),
-the air deflector mountings (1) ,
-the air deflector (2) .
For the pipes connected to the expansion valve:
aRemove the front engine cover.
aMove aside the bulkhead soundproofing.
II - REMOVAL OPERATION
a
aRemove the refrigerant circuit pipe (see 62A, Air
conditioning, Air conditioning: List and location
of components, page 62A-1) .
aFit blanking plugs on the pipe openings. Equipment required
refrigerant charging station
IMPORTANT
Consult the safety instructions and cleanliness
advice and the operation recommendations before
carrying out any repairs (see Air conditioning:
Precautions for repair).
WARNING
To prevent moisture from entering the system,
place plugs on the cold loop components which are
open to the air.
Note:
Use blanking plugs for the fuel circuits with part
numbers 77 01 208 229 or 77 01 476 857 to plug
any openings exposed to the open air. They must
be clean. Do not use any which have already been
used to plug a fuel circuit.
WARNING
Consult the device's operating manual to avoid
incorrect use.
145079
K9K
WARNING
In order to avoid any refrigerant leaks, do not
damage (deform, twist, etc.) the pipe.