lock DAEWOO MATIZ 2003 Service Manual Online

ENGINE CONTROLS 1F–215
DAEWOO M-150 BL2

The EVAP system in unable to achieve or maintain
vacuum during the diagnostic test. The amount of
decay will vary within the fuel level.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.

Coolant fan turns ON.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Although this DTC is considered a type. A diagnostic, it
acts like a type B diagnostic under certain conditions.
Whenever this diagnostic reports the system has
passed, or if the battery is disconnected, the diagnostic
must fail twice before setting a DTC. The initial failure is
not reported to the diagnostic executive or displayed ona scan tool. A passing system always reports to the
diagnostic executive immediately.
Check for the following conditions :
Missing or damaged fuel cap.
Missing or damaged O-rings at fuel vapor and EVAP
purge line canister fittings.
Cracked or punctured EVAP canister.
Damaged source vacuum line, EVAP purge line, EVAP
vent hose or fuel tank vapor line.
Poor connection at the ECM. Inspect the harness con-
nectors for the following conditions.

Backed-out terminals.

Improper mating.

Broken locks.

Improperly formed.

Damaged terminals.

Poor terminal-to-wire connection.

Damaged harness. Inspect the wiring harness to the
EVAP vent solenoid, EVAP canister purge valve, and
the fuel tank pressure sensor for an intermittent open
or short circuit.

Kinked, pinched or plugged vacuum source, EVAP
purge, or fuel tank vapor line. Verify that the lines are
not restricted.
DTC P0445 – EVAP Purge Control Circuit Fault
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Disconnect the evaporative emission (EVAP)
canister purge valve connector.
2. Measure the resistance of the EVAP canister
purge valve connector.
Does the resistance measure near within the value
specified?
30ΩGo to Step 3Go to Step 9
3
Connect a test light between EVAP canister purge
valve connector terminal 2 and ground.
Is the test light ON?
–
Go to Step 4Go to Step 6
4
1. Disconnect the ECM connector.
2. Connect a test light between the ECM connector
terminal 66 and ground.
Is the test light ON?
–
Go to Step 5Go to Step 7

1F–218 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F250
DIAGNOSTIC TROUBLE CODE (DTC) – P0462 FUEL LEVEL SENSOR LOW
V O LTA G E
Circuit Description
The engine control module(ECM) uses the fuel level in-
put from the Fuel Level Sensor to calculate expected va-
por pressures within the fuel system. Vapor pressure
vary as the fuel level changes. Vapor pressure is critical
in determining if the evaporative emission (EVAP) sys-
tem is operating properly. Fuel Level is also used to de-
termine if the Fuel level is too high or too low to be able
to accurately detect EVAP system faults. This Diagnos-
tic Trouble Code(DTC) detects a stuck fuel level sender.
Conditions for Setting the DTC

Fuel Level Sensor voltage is less than 0.05V.

Fuel Level Sensor circuit low voltage.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminal, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal-to-wire connection.
Inspect the wiring harness for damage.
A stuck Fuel Level Sensor may cause the DTC to set. If
DTC P0463 cannot be duplicated, the information in-
cluded in the Freeze Frame data can be useful in deter-
mining vehicle operating conditions when the DTC was
first set.
Resistance check for the Fuel Level Sensor.
Empty = 100 ohms or over.
Half full = about 32.5 ohms.
Full = 10 ohms or less.

1F–222 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F250
DIAGNOSTIC TROUBLE CODE (DTC) – P0463 FUEL LEVEL SENSOR HIGH
V O LTA G E
Circuit Description
The engine control module(ECM) uses the fuel level in-
put from the Fuel Level Sensor to calculate expected va-
por pressures within the fuel system. Vapor pressure
vary as the fuel level changes. Vapor pressure is critical
in determining if the evaporative emission (EVAP) sys-
tem is operating properly. Fuel Level is also used to de-
termine if the Fuel level is too high or too low to be able
to accurately detect EVAP system faults. This Diagnos-
tic Trouble Code(DTC) detects a stuck fuel level sender.
Conditions for Setting the DTC

Fuel Level Sensor voltage is higher than 4.9V.

Fuel Level Sensor circuit high voltage.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminal, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal-to-wire connection.
Inspect the wiring harness for damage.
A stuck Fuel Level Sensor may cause the DTC to set. If
DTC P0463 cannot be duplicated, the information in-
cluded in the Freeze Frame data can be useful in deter-
mining vehicle operating conditions when the DTC was
first set.
Resistance check for the Fuel Level Sensor.
Empty = 100 ohms or over.
Half full = about 32.5 ohms.
Full = 10 ohms or less.

ENGINE CONTROLS 1F–227
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0480 – Low Speed Cooling Fan Relay Circuit Fault (WITHOUT A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in low speed relay control circuit, at
terminal 39 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 87 and 39 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 30 and 87 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 39 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12

ENGINE CONTROLS 1F–231
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0480 – Low Speed Cooling Fan Relay Circuit Fault (with A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in low speed relay control circuit, at
terminal 10 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 5 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 5 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12

ENGINE CONTROLS 1F–235
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (without A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in high speed relay control circuit, at
terminal 5 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 5 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 5 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12

ENGINE CONTROLS 1F–239
DAEWOO M-150 BL2
a Freeze Frame conditions (rpm, load, vehicle speed, temperature, etc.) that .are noted. This will isolate when
the DTC failed.
DTC P0481 – High Speed Cooling Fan Relay Circuit Fault (with A/C)
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Turn the ignition switch to ON with the engine
OFF.
2. Install a scan tool.
3. Command the relay ON and OFF.
Does the relay turn ON and OFF when
commanded?
–
Go to Step 3Go to Step 5
3
1. Turn the ignition switch to LOCK.
2. Disconnect the engine control module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Using a digital voltmeter(DVM), measure the
current in high speed relay control circuit, at
terminal 39 to ground for 2 minutes.
Does the amperage measure less than the specified
value?
0.75 amps
Go to
“Diagnostic
Aids”
Go to Step 4
4
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 39 in the high speed cooling fan
relay control circuit in the ECM harness connector
to ground.
Does the DVM display infinite resistance?
–
Go to Step 12Go to Step 10
5
1. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil
terminals 86 and 85 in the relay harness
connector.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON and
OFF.
Does the test light turn ON and OFF with each
commanded?
–
Go to Step 8Go to Step 6
6
With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?
–
Go to Step 7Go to Step 11
7
1. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 10 in the
ECM harness connector.
Does the relay operate?
–
Go to Step 9Go to Step 10

1F–242 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F280
DIAGNOSTIC TROUBLE CODE (DTC) – P0501 VEHICLE SPEED NO SIGNAL
(M/T ONLY)
Circuit Description
Vehicle speed information is provided to the engine con-
trol module (ECM) by the voltage speed sensor (VSS) is
a permanent magnet generator that is mounted in the
transaxle and produces a pulsing voltage whenever ve-
hicle speed is over 3 mph (5km/h). The A/C voltage level
and the number of pulses increase with vehicle speed.
The ECM converts the pulsing voltage into mph (km/h)
and than supplies the necessary signal to the instrument
panel for speedometer / odometer operation and to the
cruise control module and multi-function alarm module
operation. The Diagnostic Trouble Code (DTC) will de-
tect if vehicle speed is reasonable according to engine
rpm and load.
Conditions for Setting the DTC

Vehicle speed is not change at least 10 seconds.

Engine speed is greater than 2,100rpm.

MAF is greater than 152mg/tdc.
Action taken when The DTCs Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

Using the scan tool can clear DTC(s).
Diagnostic Aids
An Intermittent problem may be caused by a poor con-
nection, rubbed through wire insulation, or wire that is
broken inside the insulation.
VSS signal circuit should be thoroughly checked for the
following conditions

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminals to wire connection

Physical damage to the wiring harness
Ensure the VSS is correctly torqued to the trnasaxle
housing.
Refer to “intermittents” in this Section.

ENGINE CONTROLS 1F–251
DAEWOO M-150 BL2
DTC P1535 – Evaporator Temperature Sensor High Voltage
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD II) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1.. Turn the ignition switch to LOCK.
2. Disconnect the evaporator temperature sensor.
3. Measure the resistance between evaporator
temperature sensor terminals 1 and 2.
Does the resistance within the specified value?
0ΩGo to Step 7Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 4Go to Step 5
4
Repair a short to battery between the terminal 46 of
ECM and A/C compressor relay terminal 2.
Is the repair complete?
–
Go to Step 9
–
5
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 6Go to Step 8
6
Repair a short to battery between the ECM wiring
connector terminal 46 and evaporator temperature
sensor terminal 2.
Is the repair complete?
–
Go to Step 9
–
7Replace the evaporator temperature sensor.
Is the replacement complete?–Go to Step 9–
8
1. Turn the ignition switch to LOCK.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 9
–
9
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs)
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 10Go to Step 2
10
Check if any additional DTCs are set.
Are any DTCs displayed that that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

ENGINE CONTROLS 1F–253
DAEWOO M-150 BL2
DTC P1536 – Evaporator Temperature Sensor Low Voltage
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD II) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
2.. Turn the ignition switch to LOCK.
2. Disconnect the evaporator temperature sensor.
3. Measure the resistance between evaporator
temperature sensor terminals 1 and 2.
Does the resistance within the specified value?
0ΩGo to Step 7Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 4Go to Step 5
4
Repair a short to battery between the terminal 46 of
ECM and A/C compressor relay terminal 2.
Is the repair complete?
–
Go to Step 9
–
5
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 6Go to Step 8
6
Repair a short to battery between the ECM wiring
connector terminal 46 and evaporator temperature
sensor terminal 2.
Is the repair complete?
–
Go to Step 9
–
7Replace the evaporator temperature sensor.
Is the replacement complete?–Go to Step 9–
8
1. Turn the ignition switch to LOCK.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 9
–
9
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs)
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 10Go to Step 2
10
Check if any additional DTCs are set.
Are any DTCs displayed that that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK