hood release DAEWOO MATIZ 2003 Service Repair Manual

9E–12 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B515A
Installation Procedure
1. Connect the electrical connector and the speedom-
eter cable.
2. Install the instrument cluster assembly to instrument
panel with screws.
3. Install the instrument cluster trim panel to the instru-
ment panel. Refer to “Instrument Cluster Trim Pan-
el” in this section.
4. Connect the negative battery cable.
D109B516
INSTRUMENT PANEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the driver’s airbag module from the steer-
ing wheel. Refer to Section 8B, Supplemental Inflat-
able Restraints (SIR) (For the vehicle equipped with
the airbag).
3. Remove the steering wheel from the steering col-
umn. Refer to Section 6E, Steering Wheel and Col-
umn.
4. Remove the steering column trim cover. Refer to
Section 6E, Steering Wheel and Column.
5. Remove the signal lamp switch and the wiper
switch. Refer to Section 6E, Steering Wheel and
Column.
6. Pry off the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
7. Remove the instrument cluster trim panel from the
instrument panel.

Remove the screws (1)

Using a flathead screwdriver, remove the instru-
ment cluster trim panel (2).
Notice: To prevent the instrument panel damage, cover
the flathead screwdriver with a soft cloth.
D109B517
8. Remove the hood latch release lever from the in-
strument panel. Refer to Section 9R, Body Front
End.
9. Remove the glove box assembly from the instru-
ment panel. Refer to “Glove Box” in this section.
10. Remove the passenger’s airbag module from the in-
strument panel. Refer to Section 8B, Supplemental
Inflatable Restraints (SIR) (For vehicle equipped
with the airbag).
11. Put aside the floor console after removing the
screws (1).

9E–14 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
7. Install the instrument cluster assembly. Refer to “In-
strument Cluster” in this section.
8. Install the floor console with the screws.
9. Install the passenger’s airbag module to the instru-
ment panel. Refer to Section 8B, Supplemental In-
flatable Restraints (SIR) (For vehicle equipped with
the airbag).
10. Install the glove box assembly to the instrument
panel. Refer to “Glove Box” in this section.
11. Install the hood latch release lever to the instrument
panel. Refer to Section 9R, Body Front End.
12. Install the instrument cluster trim panel to the instru-
ment cluster trim panel with the screws.
13. Install the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
14. Install the signal lamp switch and the wiper switch.
Refer to Section 6E, Steering Wheel and Column.
15. Install the steering column trim cover. Refer to Sec-
tion 6E, Steering Wheel and Column.
16. Install the steering wheel to the steering column.
17. Install the driver’s airbag module to the steering
wheel. Refer to Section 8B, Supplemental Inflatable
Restraints (SIR) (For vehicle equipped with the air-
bag).
18. Connect the negative battery cable.
D109B522
TIE–BAR
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument panel assembly. Refer to “In-
strument Panel” in this section.
3. Remove the defroster duct hose from the tie–bar.

Remove the screws (1).

Remove the defroster duct hose (2).
D19B547A
4. Remove the nuts and the steering column. Refer to
Section 6E, Steering Wheel and Column.
5. Disconnect the electrical connectors and electrical
wiring harness after removing the electrical wiring
harness strips.

Remove the electrical wiring harness strip.

Disconnect the brake switch connector (1).

Disconnect the thermostat connector (2).

Disconnect the blow motor connector (3).

Disconnect the blow motor resistance connector
(4).

Disconnect the electrical wiring harness (5).

DAEWOO M-150 BL2
SECTION 9R
BODY FRONT END
TABLE OF CONTENTS
Description and Operation 9R-2. . . . . . . . . . . . . . . . . .
Body Front End 9R-2. . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9R-3. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9R-3. . . . . . . . . . . . . . . . . . . . . . . . . .
Lubrication 9R-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fasteners 9R-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anticorrosion Materials 9R-3. . . . . . . . . . . . . . . . . . . . .
Front End Sealing 9R-4. . . . . . . . . . . . . . . . . . . . . . . . . Cowl Vent Grille 9R-4. . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 9R-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood Hinge 9R-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood Prop Rod 9R-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood Latch 9R-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood Latch Release Lever 9R-8. . . . . . . . . . . . . . . . . .
Hood Latch Release Cable 9R-9. . . . . . . . . . . . . . . . .
Fender 9R-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BODY FRONT END 9R–7
DAEWOO M-150 BL2
D109C531
3. Remove the hood prop rod from the hood prop.
a. Hood prop rod.
D109C532
Installation Procedure
1. Install the hood prop rod to the hood prop.
2. Install the hood prop to the hood with the pins.
D109C533
HOOD LATCH
Removal Procedure
1. Open the hood.
2. Remove the hood latch.

Remove the screws (1).

Disconnect the hood latch release cable (2).

Remove the hood latch (3).
D109C534
Installation Procedure
1. Connect the hood latch release cable to the latch.
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fasteners to prevent premature corrosion.
2. Install the hood latch with the screws.

9R –8 BODY FRONT END
DAEWOO M-150 BL2
D109C535
HOOD LATCH RELEASE LEVER
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the hood latch nut into the instrument panel.
a. Hood latch nut.
D109C536
2. Remove the hood latch release lever.

Disconnect the cable (1).

Remove the hood latch release lever (2).
D19C536A
Installation Procedure
1. Connect the hood latch release cable to the hood
latch lever.
D109C537
Notice: Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use the correct
fasteners to prevent premature corrosion.
2. Install the hood latch lever release to the instrument
panel with the hood latch nut.

BODY FRONT END 9R–9
DAEWOO M-150 BL2
D109C538
HOOD LATCH RELEASE CABLE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the hood latch release cable from the instru-
ment panel. Refer to “Hood Latch Release Lever” in
this section.
2. Push the cable toward the engine compartment
through the body hole.
a. Hood latch lever cable.
D19C539B
3. Open and suitably support the hood.
4. Disconnect the hood latch release cable from the
hood latch. Refer to “Hood Latch” in this section.
5. Remove the hood latch release cable after removing
the plastic strip.
a. Hood latch release cable.
D19C539C
Installation Procedure
1. Connect the hood latch release cable to the hood
latch. Refer to “Hood Latch” in this section.
2. Arrange the hood latch release cable with the plastic
strip.
3. Push the cable toward the passenger compartment
through the body hole.
4. Connect the hood latch release cable to the hood
latch release lever. Refer to “Hood Latch Release Le-
ver” in this section.
D19C501A
FENDER
Removal Procedure
1. Raise and suitably support the vehicle.
2. Remove the wheelhouse splash shield.

Remove the clip and the bolt.
a. Clip and bolt.

Remove the wheel house splash shield.
a. Wheel house splash shield.