fuse chart DAEWOO MATIZ 2003 Service Repair Manual

ENGINE CONTROLS 1F – 55
DAEWOO M-150 BL2
DIAGNOSTIC TROUBLE CODE DIAGNOSIS
CLEARING TROUBLE CODES
Notice: To prevent Engine Control Module (ECM) dam-
age, the key must be OFF when disconnecting or recon-
necting the power to the ECM (for example battery
cable, ECM pigtail connector, ECM fuse, jumper cables,
etc.).When the ECM sets a Diagnostic Trouble Code
(DTC), the Malfunction Indicator Lamp (MIL) lamp will
be turned on only for type A, B and E but a DTC will be
stored in the ECM’s memory for all types of DTC. If theproblem is intermittent, the MIL will go out after 10 sec-
onds if the fault is no longer present. The DTC will stay
in the ECM’s memory until cleared by scan tool. Remov-
ing battery voltage for 10 seconds will clear some stored
DTCs.
DTCs should be cleared after repairs have been com-
pleted. Some diagnostic tables will tell you to clear the
codes before using the chart. This allows the ECM to set
the DTC while going through the chart, which will help to
find the cause of the problem more quickly.
DIAGNOSTIC TROUBLE CODES
DTCFunctionError TypeIlluminate MIL
P0107Manifold Absolute Pressure Sensor Low VoltageAYES
P0108Manifold Absolute Pressure Sensor High voltageAYES
P0112Intake Air Temperature Sensor Low VoltageEYES
P0113Intake Air Temperature Sensor High voltageEYES
P0117Engine Coolant Temperature Sensor Low VoltageAYES
P0118Engine Coolant Temperature Sensor High voltageAYES
P0122Throttle Position Sensor Low VoltageAYES
P0123Throttle Position Sensor Hig voltageAYES
P0131Oxygen Sensor Low VoltageAYES
P0132Oxygen Sensor High VoltageAYES
P0133Oxygen Sensor No ActivityEYES
P0137Heated Oxygen Sensor Low VoltageEYES
P0138Heated Oxygen Sensor high voltageEYES
P0140Heated Oxygen Sensor No ActivityEYES
P0141Heated Oxygen Sensor Heater MalfuctionEYES
P0171Fuel Trim System Too LeanEYES
P0172Fuel Trim System Too RichEYES
P1230Fuel Pump Relay Low VoltageAYES
P1231Fuel Pump Relay High VoltageAYES
P0261Injector 1 Low VoltageAYES
P0262Injector 1 high voltageAYES
P0264Injector 2 Low VoltageAYES
P0265Injector 2 high voltageAYES
P0267Injector 3 Low VoltageAYES
P0268Injector 3 high voltageAYES
P0300Multifle Cylinder MisfireA/EBLINKING/ON
P1320Crankshatft Segment Period Segment Adaptation At LimitEYES
P1321Crankshatft Segment Period Tooth ErrorEYES
P0327Knock Sensor Circuit FaultEYES
P0335Magnetic Crankshaft Position Sensor Electrical ErrorEYES

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–61
DAEWOO M-150 BL2
DTC 25 – Warning Lamp Failure
Step Action Value(s) Yes No

1

Turn the ignition ON.
Is the warning lamp constantly ON?
–

Go to Step 2

Go to Step 9

2

Make sure the SDM connector is attached correctly.
Does the warning lamp turn OFF?
–


Go to
Diagnostic
System Check
Go to Step 3





3





1. Check for indications of the diagnostic trouble
code (DTC) other than the code 25.
2. Go to the appropriate DTC charts and repair each
additional problem.
3. Do the diagnostic system check.
Does the scan tool still indicate the code 25?



–




Go to Step 4




System OK









4









Check for a short to ground between the SDM and
the warning lamp using the following method:
1. Turn the ignition OFF.
2. Disconnect the connector C208.
3. Connect one ohmmeter lead to ground.
4. Touch the other ohmmeter lead to the terminal 3
of the connector C208 on the instrument harness
side.

Refer to ‘‘Diagnostic Illustration 14’’ in this
section.
Does the ohmmeter indicate the specified value?







∞








Go to Step 6








Go to Step 5



5



Repair the short to ground in the instrument
harness.
Is the repair complete?

–



Go to
Diagnostic
System Check

–






6






1. The connector C208 remains disconnected.
2. One lead of the ohmmeter remains connected to
ground.
3. Move the ohmmeter lead at the connector C208
to the SDM side of the connector.

Refer to ‘‘Diagnostic Illustration 13’’ in this
section.
Does the ohmmeter indicate the specified value?




∞





Go to Step 7





Go to Step 8

7


Replace the SDM.
Is the repair complete?

–


Go to
Diagnostic
System Check

–



8




1. Disconnect the negative battery cable.
2. Replace the SIR wiring harness.
3. Do the diagnostic system check.
Does the code 25 still show?



–



Go to Step 5



System OK

9

Check the fuse F1.
Is the fuse F1 blown?
–

Go to Step 10

Go to Step 11





10





1. With the connector C208 temporarily
disconnected, check for a short to ground
between the fuse F1 and the warning lamp.
2. Make a repair, if needed.
3. Replace the fuse F1.
Is the repair complete?



–





Go to
Diagnostic
System Check




–

DAEWOO M-150 BL2
SECTION 9A
BODY WIRING SYSTEM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9A-2. . . . . . . . . . . . . . . . . .
How to Read Electrical Wiring Diagram 9A-2. . . . . . .
How to Check Terminal Number of Connector 9A-4.
Special Tools and Equipment 9A-5. . . . . . . . . . . . . . .
Special Tools Table 9A-5. . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9A-6. . . . . . . . . . .
Wire Color Chart 9A-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Power Distribution Schematic 9A-7. . . . . . . . . . . . . . .
Relay & Fuse Box Locator (Engine Room) 9A-8. . . .
Fuse Box Locator
(Passenger Compartment) 9A-9. . . . . . . . . . . . . . . . Fuse Chart 9A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Harness Routing 9A-11. . . . . . . . . . . . . . . . . . . .
Engine Harness Routing 9A-12. . . . . . . . . . . . . . . . . . .
Instrument Harness Routing 9A-14. . . . . . . . . . . . . . .
Airbag Harness Routing 9A-16. . . . . . . . . . . . . . . . . . .
Body Harness Routing 9A-17. . . . . . . . . . . . . . . . . . . .
Front Door Harness Routing 9A-19. . . . . . . . . . . . . . .
Rear Door Harness Routing 9A-20. . . . . . . . . . . . . . . .
Tailgate Harness Routing 9A-21. . . . . . . . . . . . . . . . . .

BODY WIRING SYSTEM 9A–3
DAEWOO M-150 BL2
Contents of Electrical Wiring Diagram
PositionExplanation
A
–The box above the fuse box: Power supply lines
–Power supply lines: 30, 15, 15A, Ka, 58, 50
–Refer to “Circuit Identification Symbol” in this section for more details.
B
–Ef10 or F3: Fuse Number

Ef10: Fuse No 10 in the engine room fuse box

F3: Fuse No 3 in the passenger room fuse box
–40A: Fuse Capacity
–Refer to “Relay Box Locator” and “Fuse Box Locator” in this section.
C
–Connector
–Connector No C202, terminal No 10
–Refer to “How to Check Terminal Number of Connect” in this section
D–Internal circuit of component (Relay)
(Component Name, Terminal Number)
E–Internal circuit of component (Switch)
(Terminal Number)
F–Wiring Harness Color
–Refer to “Wire Color Chart” in this section
G
–Ground line.
–G402: Ground Position
–In case of the ground numberless, this means the body ground.
Circuit Identification Symbol
Identification SymbolMeaning
CConnector
EfFuse in engine room fuse box
FFuse in passenger compartment fuse box
GGround

9A–10 BODY WIRING SYSTEM
DAEWOO M-150 BL2
FUSE CHART
FuseRating/ SourceCircuit
Ef1 (Engine Fuse)50ABATABS
Ef240ABATIgnition Switch, Instrument Panel Fuse Block
(F5, F11 ~ F13)
Ef310ABATFuel cut-off Switch (Inertia Switch)
Ef410AIGN 1Fuel, EBCM, Generator, VSS, Fuel Pump Relay, Main Relay,
Ignition Coil
Ef5––Not Used
Ef620ABATBlower Motor
Ef715ABATRear Window Defogger
Ef810ABATHeadlamp Hi Beam, Right Side
Ef910ABATHeadlamp Hi Beam, Left Side
Ef1010ABATHeadlamp Lo Beam, Right Side
Ef1110ABATHeadlamp Lo Beam, Left Side
Ef1210A58Tail and Illumination Lamps, Right Side
Ef1310A58Tail and Illumination Lamps, Left Side
Ef1410ABATA/C Compressor
Ef1530ABATRadiator Fan
Ef1610A–Spare
Ef1710ABATHorn
Ef1820ABATHeadlamp Relay, Hi Beam Passing, DRL Module
Ef1915ABATECM, Main Relay
Ef2015ABATFront Fog Lamp
Ef2115A–Spare
F1 (Fuse)10AIGN 1Cluster, Clock, IMMO, Anti-Theft Control Unit,
DRL Relay
F210AIGN 1SDM
F325AIGN 1Hazard Switch, DRL Module
F410AIGN 1Turn Signal Lamp
F515ABATStop Lamp
F610AACCAudio
F720AACCCigar Light
F815AIGN 2Wiper
F915AIGN 2Rear Wiper Motor, Front & Rear Washer, Backup Lamp
F1010AIGN 2Auto Miror Switch
F1110AEf2IMMO, Audio, Room Lamp
F1215AEf2Hazard, Clock
F1320AEf2Anti-Theft Control Unit, Door Lock
F1420ASTStarter Motor