lug pattern DAEWOO MATIZ 2003 Service Repair Manual

1F–288 ENGINE CONTROLS
DAEWOO M-150 BL2
LACK OF POWER, SLUGGISHNESS, OR SPONGINESS
Definition: The engine delivers less than expected pow-
er. There is little or no increase in speed when the accel-
erator pedal is partially applied.
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Verify the customer’s complaint.
2. Compare the performance of the customer’s
vehicle with a similar unit.
Does the problem exist?
–
Go to Step 3System OK
3
1. Inspect the air filter for excessive contamination.
2. Replace the air filter as needed.
3. Check the transaxle shift pattern and down shift
operation.
Does the transaxle operate properly?
–
Go to Step 4Go to Step 5
4Check the fuel system pressure.
Is the fuel system pressure within specifications?380 kPa
(55 psi)
Go to Step 7Go to Step 6
5Repair the transaxle as needed.
Is the repair complete?–System OK–
6Repair the fuel system as needed.
Is the repair complete?–System OK–
7Check for a restricted fuel filter or contaminated fuel.
Is the problem found?–Go to Step 8Go to Step 9
8Repair or replace any components as needed.
Is the repair complete?–System OK–
9
1. Check the ignition system output for all of the
cylinders using a spark tester.
2. Check for proper ignition control operation.
Is the ignition system operating properly?
–
Go to Step 10Go to Step 11
10
1. With the engine at normal operating temperature,
connect a vacuum gauge to a vacuum port on the
intake manifold.
2. Operate the engine at 1000 rpm.
3. Record the vacuum reading.
4. Increase the engine speed to 2500 rpm.
5. Note the vacuum reading at a steady 2500 rpm.
Does the vacuum decrease more than the value
specified?
10 kPa
(3 in Hg)
Go to Step 12Go to Step 15
11
Repair or replace any ignition system components
as needed.
Is the repair complete?
–
System OK
–
12
Inspect the exhaust system for restrictions and
damaged or collapsed pipes.
Is the problem found?
–
Go to Step 13Go to Step 14
13Repair or replace any components as needed.
Is the repair complete?–System OK–
14
1. Check the cylinder compression and valve timing.
2. Inspect the camshaft for excessive wear.
Is the problem found?
–
Go to Step 15Go to Step 16

1F–296 ENGINE CONTROLS
DAEWOO M-150 BL2
POOR FUEL ECONOMY
Definition: Fuel economy, as measured by an actual
road test, is noticeably lower than expected. Also, fuel
economy is noticeably lower than it was on this vehicle
at one time, as previously shown by an actual road test.
Important: Driving habits affect fuel economy. Check
the owner’s driving habits by asking the following ques-
tions:1. Is the A/C system (i.e. defroster mode) turned on all
the time?
2. Are the tires at the correct air pressure?
3. Have excessively heavy loads been carried?
4. Does the driver accelerate too much and too often?
Suggest the driver read the section in the owner’s
manual about fuel economy.
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Inspect the air filter for excessive contamination.
2. Inspect for fuel system leaks.
Are all needed checks complete?
–
Go to Step 3
–
3
1. Inspect the spark plugs for excessive wear,
insulation cracks, improper gap, or heavy
deposits.
2. Replace any faulty spark plugs.
3. Inspect the ignition wires for cracking, hardness,
and proper connections.
Are all needed checks and repairs complete?
–
Go to Step 4
–
4
1. Inspect the engine coolant level.
2. Check the thermostat for being always open or for
an incorrect heat range.
3. Replace the thermostat as needed.
Are all needed checks and repairs complete?
–
Go to Step 4
–
5
1. Check the transaxle shift pattern. Ensure all
transaxle gears are functioning.
2. Check for proper calibration of the speedometer.
3. Check the brakes for dragging.
4. Check the cylinder compression.
5. Repair, replace, or adjust any components as
needed.
Are all checks and needed repairs complete?
–
System OK
–