intake manifold DAEWOO MATIZ 2003 Service Repair Manual

GENERAL ENGINE INFORMATION 1A–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
ENGINE COMPARTMENT (TYPICAL)
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D102A401
1 Power Steering Oil Reservoir
2 Coolant Reservoir
3 Canister
4 Canister Solenoid
5 Manifold Absolute Pressure (MAP) Sensor
6 Intake Manifold
7 Ignition Coil
8 Idle Air Control (IAC) Valve
9 Throttle Position (TP) Sensor
10 Throttle Body
11 Brake Fluid Reservoir
12 Wiper Motor13 Battery
14 Fuse Box
15 Air Cleaner Housing
16 Resonator
17 PCV Hose
18 Distributor
19 Exhaust Manifold
20 Snorkel
21 Engine
22 Washer Fluid Reservoir
23 Oil Level Gauge
24 Oil Filler Cap

1A–4 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
ENGINE COMPARTMENT (EURO III)
(Left–Hand Drive Shown, Right–Hand Drive Similar)
MAA1A010
1 Power Steering Oil Reservoir
2 Coolant Reservoir
3 Canister Purge Solenoid
4 Manifold Absolute Pressure (MAP) Sensor
5 Intake Manifold
6 Throttle Position (TP) Sensor
7 Throttle Body
8 Idle Air Control (IAC) Valve
9 Brake Fluid Reservoir
10 Wiper Motor11 Battery
12 Fuse Box
13 Air Cleaner Housing
14 Resonator
15 Electronic Ignition System Ignition Coil
16 Exhaust Manifold
17 Snorkel
18 Engine
20 Washer Fluid Reservoir
19 Oil Level Gauge
21 Oil Filler Cap

1A–6 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Hard Starting (WithOthers
Broken timing belt.
Replace the belt.
normal cranking)
Malfunction of Positive
Crankcase Ventilation (PCV)
valve.
Check and replace Positive
Crankcase Ventilation (PCV)
valve if needed.

Loosening, damage or
leakage of the vacuum hose.
Connect the hose correctly
or replace it.

Leakage of intake system.
Replace intake system.
Lack of Engine PowerDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Improper ignition timing.
Adjust the ignition timing.
Ignition System
Faulty spark plug.
Adjust or replace the spark
plug.

Malfunction of the distributor.
Repair or replace the
distributor. Check the rotor.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.
Others
Clogged exhaust system.
Check and repair the
system.

Clogged or contaminated air
cleaner element.
Clean or replace the air
cleaner element.

Leak of the intake manifold
gasket.
Replace the gasket.

Dragging brakes.
Repair or replace the
brakes.

Slipping clutch.
Adjust or replace the clutch.
Rough Engine IdlingDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Clogged fuel pipe.
Clean the pipe.
Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.

Malfunction of the fuel
pressure regulator.
Replace the regulator.
Malfunction of
Ignition System
Malfunction of the spark
plug.
Adjust or replace the spark
plug.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.

Worn distributor cap terminal
or accumulated carbon in
the distributor cap.
Replace or clean the
distributor cap.

GENERAL ENGINE INFORMATION 1A–7
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 Condition Probable cause Correction
Rough Engine IdlingMalfunction of
Ignition System
Loosening or damage of the
distributor rotor or cap.
Replace the rotor or cap.

Poor ignition timing.
Adjust the ignition timing.

Malfunction of the ignition
coil.
Replace the ignition coil.
Others
Clogged or contaminated air
cleaner element.
Clean or replace the air
cleaner element.

Leak of the intake manifold
gasket.
Replace the gasket.

Malfunction of Positive
Crankcase Ventilation (PCV)
valve.
Check the valve or replace it
if needed.

Poor connection or damage
or leakage of the vacuum
hose.
Connect the hose correctly
or replace it.
Engine Hesitate (Upon
pressing accelerating
pedal, the engineDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
makes delayed
response. ThisMalfunction of
Poor ignition timing.
Adjust the ignition timing.response. This
situation is remarkable
when cruising orIgnition System
Poor spark plug or poor
adjustment of the plug gap.
Replace the plug or adjust
the gap.
starting.)
Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.
Others
Malfunction of the air cleaner
system.
Clean or replace the air
cleaner system.

Leak of the intake manifold
gasket.
Replace the gasket.
Engine Surging
(Engine power makes
fluctuation in a fixedDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
speed and speed
changes withoutMalfunction of
Clogged fuel pipe.
Clean the pipe.changes without
operating the
accelerating pedal.)Fuel System
Clogged or contaminated
fuel filter.
Replace the filter.

Malfunction of the fuel
pressure regulator.
Replace the fuel pressure
regulator.
Malfunction of
Ignition System
Malfunction of the spark
plug.
Adjust or replace the spark
plug.

Electric leakage or poor
connection of the high
tension cable.
Connect the cable correctly
or replace it.

Worn distributor cap terminal
or accumulated carbon in
the distributor cap.
Clean or replace the
distributor cap.

Loosening or damage of the
distributor rotor or the cap.
Replace the distributor rotor
or the cap.

Poor ignition timing.
Adjust the ignition timing.

1A–8 GENERAL ENGINE INFORMATION
DAEWOO M-150 BL2
GENERAL DIAGNOSIS (Cont’d)
 
 Condition
 
 Probable cause
 
 Correction
Engine Surging
(Engine power makes
fluctuation in a fixedOthers
Leak of the intake manifold
gasket.
Clean or replace the gasket.
speed and speed
changes without
operating the
accelerating pedal.)
Leakage of the vacuum hose.
Connect the hose correctly
or replace it.
Excessive Detonation
(According to theOverheated
Engine
Refer to “Overheat” in this
page.
Refer to “Overheat” in this
page.
opening range of
throttle valve,Malfunction of
Abnormal spark plug.
Replace the spark plug.
knocking sound of
metallic is made withIgnition System
Poor ignition timing.
Adjust the ignition timing.metallic is made with
abnormal explosion.)

Electric leakage or poor
connection of the high tension
cable.
Connect the cable correctly
or replace it.
Malfunction of
Fuel System
Clogged or contaminated fuel
filter and fuel pipe.
Clean or replace the fuel
filter and the fuel pipe.
Others
Leak of the intake manifold
gasket.
Replace the gasket.

Excessive carbon deposit due
to abnormal combustion.
Remove the carbon.
OverheatMalfunction of
Lack of coolant.
Refill coolant.
Cooling System
Malfunction of the thermostat.
Replace the thermostat.

Malfunction of the cooling fan.
Check or replace the cooling
fan.

Poor water pump
performance.
Replace the pump.

Clogged or leaky radiator.
Clean, repair or replace the
radiator.
Malfunction of
Lubrication
Poor engine oil.
Replace engine oil with the
specified one.
System
Blocking oil filter or strainer.
Clean or replace the oil filter
or the strainer.

Lack of engine oil.
Refill oil.

Poor oil pump performance.
Replace or repair the pump.

Leakage of oil.
Repair.
Other
Damaged cylinder head
gasket.
Replace the gasket.
Poor Fuel
ConsumptionDecline of
Compression
Pressure
Refer to “Page 1A–5”.
Refer to “Page 1A–5”.
Malfunction of
Fuel System
Leakage of the fuel tank or
the fuel pipe.
Repair or replace the fuel
tank or the fuel pipe.

DAEWOO M-150 BL2
SECTION 1B
SOHC ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 1B-2. . . . . . . . . . . . . . . . . .
Engine Type 1B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Lubrication 1B-2. . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train 1B-2. . . . . . . . . . . . . .
Engine Block 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crankshaft 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Rod 1B-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
Piston, Piston Ring and Piston Pin 1B-3. . . . . . . . . . .
Timing Belt and Pulley 1B-4. . . . . . . . . . . . . . . . . . . . .
Engine Mount 1B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 1B-5. . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head 1B-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block 1B-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold & Air Flow System 1B-7. . . . . . . . . . . . . . . . .
Timing Belt & Engine Mount 1B-8. . . . . . . . . . . . . . . .
Diagnostic Information and Procedure 1B-9. . . . . . .
Compression Pressure Check 1B-9. . . . . . . . . . . . . . .
Oil Pressure Check 1B-9. . . . . . . . . . . . . . . . . . . . . . . .
Adjustment of Valve Clearance 1B-10. . . . . . . . . . . . .
Ignition Timing Check and Adjustment
(Typical) 1B-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Timing Check and Adjustment 1B-12. . . . . . . .
Repair Instructions 1B-14. . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 1B-14. . . . . . . . . . . . . . . . . . . . . . . . . Air Filter Assembly 1B-14. . . . . . . . . . . . . . . . . . . . . . .
Air Filter Element 1B-15. . . . . . . . . . . . . . . . . . . . . . . . .
Positive Crankcase Ventilation (PCV) Hose
and Valve 1B-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake Manifold 1B-16. . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust Manifold (Typical) 1B-18. . . . . . . . . . . . . . . . .
Exhaust Manifold (Euro III) 1B-20. . . . . . . . . . . . . . . .
Timing Belt 1B-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pan 1B-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil Pump 1B-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor Case 1B-26. . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Gasket 1B-28. . . . . . . . . . . . . . . . .
Engine Mount Damping Block 1B-32. . . . . . . . . . . . . .
Engine Mount Front Damping Bush 1B-34. . . . . . . . .
Engine Assembly 1B-35. . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cylinder Head and Valve Train
Components 1B-47. . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Block Components 1B-59. . . . . . . . . . . . . . . . .
Specifications 1B-71. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Specifications 1B-71. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 1B-73. . . . . . . . . .
Special Tools 1B-75. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools Table 1B-75. . . . . . . . . . . . . . . . . . . . . . .

1B – 2 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
ENGINE TYPE
The engine is 4-cycle, water-cooled, in-line 3 cylinders
with displacement of 796cc (68.5×72.0mm) (2.70×
2.83 in.).
Engine model
(Specifications)F8C Type SOHC /
2 Valve (MPI)
Maximum power (kw/rpm)37.5 / 6,000
Maximum torque (N
m/rpm)68.6 / 4,600
Compression ratio9.3 : 1
D102B001
ENGINE LUBRICATION
The engine lubrication is of the wetsump method to draw
up the oil forced by the oil pump. The oil pump is of a
trochoid type, and mounted on crankshaft at crankshaft
pulley side (a). Oil is drawn up through oil pump pickup
tube (b) and passed through pump (c) to oil filter (d). The
filtered oil flows into two paths in engine block. In one
path (e), oil reaches crankshaft journal bearings. Oil
from crankshaft journal bearings is supplied to connect-
ing rod bearings by means of intersecting passages
drilled in crankshaft, and then injected from a small hole
provided on big end of connecting rod to lubricate piston
(f), rings, and cylinder wall. In another path (g), oil goes
up to cylinder head and lubricates rocker arm (i), valve
(j), camshaft (k), etc. through the oil hole provided on the
rocker arm shaft (h).
D102B002
CYLINDER HEAD AND VALVE TRAIN
The cylinder head is made of cast aluminum alloy for
better strength in hardness with lightweight, and cam-
shaft (k) and rocker arm shaft (h) arranged in-line sup-
port.
D102B003
The combustion chambers are formed into the manifold
combustion chambers with increased squish parts for
better combustion efficiency and its intake and exhaust

SOHC ENGINE MECANICAL 1B–7
DAEWOO M-150 BL2
MANIFOLD & AIR FLOW SYSTEM
D21B0021
1 Intake Manifold
2 Exhaust Gas Recirculation (EGR) Pipe
3 Exhaust Gas Recirculation (EGR) Valve and
Solenoid
4 Throttle Body Assembly
5 Air Filter Assembly
6 Resonator7 Snorkel
8 Oxygen Sensor
9 Exhaust Manifold
10 Exhaust Manifold Heat Shield
11 Exhaust Manifold Heat Shield (Euro III)
12 Exhaust Manifold (Euro III)

1D–8 ENGINE COOLING
DAEWOO M-150 BL2
COOLING SYSTEM DIAGNOSIS
Condition Probable Cause Correction
Engine OverheatsA loss of the coolant.Add the coolant.
A weak coolant solution.Confirm that the coolant solution is a
50/50 mixture of ethylene glycol and
water.
Any dirt, any leaves, or any insects
on the front of the radiator.Clean the front of the radiator.
The leakage from the hoses, the
coolant pump, the heater, the
thermostat housing, the radiator, the
heater core, or the head gasket.Replace any damaged components.
A faulty thermostat.Replace a damaged thermostat.
Retarded ignition timing.Perform an ECM code diagnosis.
Confirm the integrity of the timing
belt.
An improperly operating electric
cooling fan.Replace the electric cooling fan.
Plugged or rotted radiator hoses.Replace any damaged radiator
hoses.
A faulty water pump.Replace a faulty water pump.
A faulty surge tank cap.Replace a faulty surge tank cap.
A cracked or plugged cylinder head
or engine block.Repair the damaged cylinder head or
the damaged engine block.
A faulty radiator.Replace a faulty radiator.
Loss of CoolantA leak in the radiator.Replace a damaged radiator.
A leak in the surge tank or the hose.Replace the surge tank or the hose.
Looseness or damage of radiator
hoses, heater hoses, or connections.Reseat the hoses.
Replace the hoses or the clamps.
Leaks in the coolant pump seal.Replace the coolant pump seal.
Leaks in the coolant pump gasket.Replace the coolant pump gasket.
An improper cylinder head torque.Tighten the cylinder head bolts to
specifications.
Replace the cylinder head gasket, if
needed.
Leaks in the intake manifold, cylinder
head gasket, heater core.Repair or replace any components,
as needed to correct the leak.
Engine Fails to Reach
Normal OperatingThermostat to be stuck open or to be
wrong type.Install a new thermostat of the
correct type and heat range.
Temperature or Cool Air
from the HeaterThe coolant level below the MIN
mark on the surge tank.Add sufficient coolant to raise the
fluid to the specified mark on the
surge tank.

1D–14 ENGINE COOLING
DAEWOO M-150 BL2
MAA1D020
4. Remove the thermostat.
Remove the bolts.
Remove the thermostat housing.
Remove the thermostat with the gasket.
5. Check the gasket for crack or other damage.
6. Inspect the valve seat for foreign matter that could
prevent the valve from seating properly.
7. Inspect the thermostat for proper operation. Refer to
“Thermostat Test” in this section.
MAA1D011
Installation Procedure
1. Install the thermostat with the bolts and the thermo-
stat housing.
Tighten
Tighten the mounting bolts to 8–15 Nm (71–130
lb-in).
2. Secure the upper radiator hose to the thermostat
housing with a hose clamp.
3. Refill the engine cooling system. Refer to “Draining
and Refilling the Cooling System” in this section.
4. Install the air filter assembly. Refer to Section 1B,
SOHC Engine Mechanical.
D102D515
COOLANT TEMPERATURE SENSOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Draining and Refilling the Cooling
System” in this section.
3. Remove the coolant temperature sensor.
Disconnect the electrical connector (1).
Remove the coolant temperature sensor (2).
D12D516A
10 Nm
Installation Procedure
1. Install the coolant temperature sensor into the
threaded hole in the intake manifold.
Tighten
Tighten the coolant temperature sensor to 10 Nm
(89 lb-in).
Connect the electrical connector to the coolant
temperature sensor (1).
2. Connect the lower radiator hose and refill the coolant.
Refer to “Draining and refilling the cooling system” in
this section.
3. Connect the negative battery cable.