intake manifold DAEWOO MATIZ 2003 Service Owner's Guide
[x] Cancel search | Manufacturer: DAEWOO, Model Year: 2003, Model line: MATIZ, Model: DAEWOO MATIZ 2003Pages: 1184, PDF Size: 36 MB
Page 286 of 1184
1F–188 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F230
DIAGNOSTIC TROUBLE CODE (DTC) – P1403 ELECTRIC EXHAUST GAS
RECIRCULATION VALVE FAILURE
Circuit Description
An Electric Exhaust Gas Re-circulation (EEGR) system
is used to lower oxides of nitrogen (NOX) emission lev-
els caused by high combustion temperatures. It a ac-
complishes this by feeding small amounts of exhaust
gases back into the combustion chamber. When the air/
fuel mixture is diluted with the exhaust gases, combus-
tion temperatures are reduced.
A linear EEGR valve is used on this system. The linear
EEGR valve is designed to accurately supply exhaust
gases to the engine without the use of intake manifold
vacuum. The valve controls exhaust flow going into the
intake manifold from the exhaust manifold fhrough an
orifice with a engine control module(ECM) controlled
pintle. The ECM controls the pintle position using inputs
from the Throttle Position (TP) and the Manifold Abso-
lute Pressure (MAP) sensor. The ECM then commands
the EEGR valve to operate when necessary by control-
ling an ignition signal through the ECM. This can be
monitored on a scan tool as the Desired EEGR position.
The ECM monitors the results of its command through a
feedback signal. By sending a 5 volt reference and a
ground to the EEGR valve, a voltage signal representing
the EEGR valve pintle position is sent to the ECM. This
feedback signal can also be monitored on a scan tool
and is the actual position of the EEGR pintle. The actual
EEGR position should always be near the commanded
or Desired EEGR position.
ThisDiagnostic Trouble Code(DTC) will detect an open
or short circuit.
Conditions for Setting THE DTC
Engine Coolant Temperature(ECT) is greater than
80°C(176°F).Intake Air Temperature(IAT) is greater than 15°C
(59°F).
Manifold Absolute Pressure is greater than 75kPA.
The open EEGR value is higher than 3%.
Mass Air Flow is between 92 ~157mg/tdc.
Engine Speed Is Between 2,500~2,900rpm.
EEGR potentiometer voltage is less than 0.4V.
EEGR potentiometer voltage is higher than 1.75V or
integral term of EEGR controller blocked in high or
low limit.
DTCs P0107, P0108, P0112, P0113, P0117, P0118,
P0122, P0123, P0131, P0300, P0335, P0336,
P0341, P0342, P1671, P1672, P1673 are NOT SET.
Action Taken When the DTC Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EEGR valve may freeze and stick in cold weather at
times. After the vehicle is brought into a warm shop for
Page 290 of 1184
1F–192 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F230
DIAGNOSTIC TROUBLE CODE (DTC) – P0404 ELECTRIC EXHAUST GAS
RECIRCULATION OPENED
Circuit Description
An Electric Exhaust Gas Re-circulation (EEGR) system
is used to lower oxides of nitrogen (NOX) emission lev-
els caused by high combustion temperatures. It a ac-
complishes this by feeding small amounts of exhaust
gases back into the combustion chamber. When the air/
fuel mixture is diluted with the exhaust gases, combus-
tion temperatures are reduced.
A linear EEGR valve is used on this system. The linear
EEGR valve is designed to accurately supply exhaust
gases to the engine without the use of intake manifold
vacuum. The valve controls exhaust flow going into the
intake manifold from the exhaust manifold fhrough an
orifice with a engine control module(ECM) controlled
pintle. The ECM controls the pintle position using inputs
from the Throttle Position (TP) and the Manifold Abso-
lute Pressure (MAP) sensor. The ECM then commands
the EEGR valve to operate when necessary by control-
ling an ignition signal through the ECM. This can be
monitored on a scan tool as the Desired EEGR position.
The ECM monitors the results of its command through a
feedback signal. By sending a 5 volt reference and a
ground to the EEGR valve, a voltage signal representing
the EEGR valve pintle position is sent to the ECM. This
feedback signal can also be monitored on a scan tool
and is the actual position of the EEGR pintle. The actual
EEGR position should always be near the commanded
or Desired EEGR position.
ThisDiagnostic Trouble Code(DTC) will detect an open
or short circuit.Conditions for Setting THE DTC
EEGR circuit low voltage.
Action Taken When the DTC Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
EEGR is disabled.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EEGR valve may freeze and stick in cold weather at
times. After the vehicle is brought into a warm shop for
repairs, the valve warms and the problem disappears.
By watching the Actual EEGR and desired EEGR posi-
tions on a cold vehicle with a scan tool, the fault can be
easily verified. Check the Freeze Frame data to deter-
mine if the DTC set when the vehicle was cold by view-
ing the Engine Coolant Temperature (ECT).
Page 294 of 1184
1F–196 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F230
DIAGNOSTIC TROUBLE CODE (DTC) – P1404 ELECTRIC EXHAUST GAS
RECIRCULATION CLOSED
Circuit Description
An Electric Exhaust Gas Re-circulation (EEGR) system
is used to lower oxides of nitrogen (NOX) emission lev-
els caused by high combustion temperatures. It a ac-
complishes this by feeding small amounts of exhaust
gases back into the combustion chamber. When the air/
fuel mixture is diluted with the exhaust gases, combus-
tion temperatures are reduced.
A linear EEGR valve is used on this system. The linear
EEGR valve is designed to accurately supply exhaust
gases to the engine without the use of intake manifold
vacuum. The valve controls exhaust flow going into the
intake manifold from the exhaust manifold fhrough an
orifice with a engine control module(ECM) controlled
pintle. The ECM controls the pintle position using inputs
from the Throttle Position (TP) and the Manifold Abso-
lute Pressure (MAP) sensor. The ECM then commands
the EEGR valve to operate when necessary by control-
ling an ignition signal through the ECM. This can be
monitored on a scan tool as the Desired EEGR position.
The ECM monitors the results of its command through a
feedback signal. By sending a 5 volt reference and a
ground to the EEGR valve, a voltage signal representing
the EEGR valve pintle position is sent to the ECM. This
feedback signal can also be monitored on a scan tool
and is the actual position of the EEGR pintle. The actual
EEGR position should always be near the commanded
or Desired EEGR position.
ThisDiagnostic Trouble Code(DTC) will detect an open
or short circuit.Conditions for Setting THE DTC
EEGR circuit high voltage.
Action Taken When The DTCs Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
EEGR is disabled.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EEGR valve may freeze and stick in cold weather at
times. After the vehicle is brought into a warm shop for
repairs, the valve warms and the problem disappears.
By watching the Actual EEGR and desired EEGR posi-
tions on a cold vehicle with a scan tool, the fault can be
easily verified. Check the Freeze Frame data to deter-
mine if the DTC set when the vehicle was cold by view-
ing the Engine Coolant Temperature (ECT).
Page 298 of 1184
1F–200 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F230
DIAGNOSTIC TROUBLE CODE (DTC) – P0405 EEGR PINTLE POSITION
SENSOR LOW VOLTAGE
Circuit Description
An Electric Exhaust Gas Re-circulation (EEGR) system
is used to lower oxides of nitrogen (NOX) emission lev-
els caused by high combustion temperatures. It a ac-
complishes this by feeding small amounts of exhaust
gases back into the combustion chamber. When the air/
fuel mixture is diluted with the exhaust gases, combus-
tion temperatures are reduced.
A linear EEGR valve is used on this system. The linear
EEGR valve is designed to accurately supply exhaust
gases to the engine without the use of intake manifold
vacuum. The valve controls exhaust flow going into the
intake manifold from the exhaust manifold fhrough an
orifice with a engine control module(ECM) controlled
pintle. The ECM controls the pintle position using inputs
from the Throttle Position (TP) and the Manifold Abso-
lute Pressure (MAP) sensor. The ECM then commands
the EEGR valve to operate when necessary by control-
ling an ignition signal through the ECM. This can be
monitored on a scan tool as the Desired EEGR position.
The ECM monitors the results of its command through a
feedback signal. By sending a 5 volt reference and a
ground to the EEGR valve, a voltage signal representing
the EEGR valve pintle position is sent to the ECM. This
feedback signal can also be monitored on a scan tool
and is the actual position of the EEGR pintle. The actual
EEGR position should always be near the commanded
or Desired EEGR position.
ThisDiagnostic Trouble Code(DTC) will detect an open
or short circuit.Conditions for Setting THE DTC
EEGR voltage is less than 0.01V.
EEGR potentiometer circuit low voltage.
Action Taken When The DTCs Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
EEGR is disabled.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EEGR valve may freeze and stick in cold weather at
times. After the vehicle is brought into a warm shop for
repairs, the valve warms and the problem disappears.
By watching the Actual EEGR and desired EEGR posi-
tions on a cold vehicle with a scan tool, the fault can be
easily verified. Check the Freeze Frame data to deter-
mine if the DTC set when the vehicle was cold by view-
ing the Engine Coolant Temperature (ECT).
Page 302 of 1184
1F–204 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F230
DIAGNOSTIC TROUBLE CODE (DTC) – P0406 EEGR PINTLE POSITION
SENSOR HIGH VOLTAGE
Circuit Description
An Electric Exhaust Gas Re-circulation (EEGR) system
is used to lower oxides of nitrogen (NOX) emission lev-
els caused by high combustion temperatures. It a ac-
complishes this by feeding small amounts of exhaust
gases back into the combustion chamber. When the air/
fuel mixture is diluted with the exhaust gases, combus-
tion temperatures are reduced.
A linear EEGR valve is used on this system. The linear
EEGR valve is designed to accurately supply exhaust
gases to the engine without the use of intake manifold
vacuum. The valve controls exhaust flow going into the
intake manifold from the exhaust manifold fhrough an
orifice with a engine control module(ECM) controlled
pintle. The ECM controls the pintle position using inputs
from the Throttle Position (TP) and the Manifold Abso-
lute Pressure (MAP) sensor. The ECM then commands
the EEGR valve to operate when necessary by control-
ling an ignition signal through the ECM. This can be
monitored on a scan tool as the Desired EEGR position.
The ECM monitors the results of its command through a
feedback signal. By sending a 5 volt reference and a
ground to the EEGR valve, a voltage signal representing
the EEGR valve pintle position is sent to the ECM. This
feedback signal can also be monitored on a scan tool
and is the actual position of the EEGR pintle. The actual
EEGR position should always be near the commanded
or Desired EEGR position.
This Diagnostic Trouble Code(DTC) will detect an open
or short circuit.Conditions for Setting THE DTC
EEGR voltage is higher than 4.99V.
EEGR potentiometer circuit high voltage.
Action Taken When The DTCs Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
EEGR is disabled.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EEGR valve may freeze and stick in cold weather at
times. After the vehicle is brought into a warm shop for
repairs, the valve warms and the problem disappears.
By watching the Actual EEGR and desired EEGR posi-
tions on a cold vehicle with a scan tool, the fault can be
easily verified. Check the Freeze Frame data to deter-
mine if the DTC set when the vehicle was cold by view-
ing the Engine Coolant Temperature (ECT).
Page 308 of 1184
1F–210 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F240
DIAGNOSTIC TROUBLE CODE (DTC) – P0444 EVAP PURGE CONTROL
CIRCUIT NO SIGNAL
Circuit Description
The evaporative emission (EVAP) system includes the
following components :
Fuel tank.
EVAP vent solenoid.
Fuel pipes and hoses.
Fuel vapor lines.
Fuel cap.
EVAP canister.
Purge lines.
EVAP canister purge valve.
EVAP service port.
The evaporative emission system is checked by apply-
ing vacuum to the EVAP system and monitoring for a
vacuum decay. The engine control module(ECM) moni-
tors the vacuum level through the fuel tank pressure
sensor signal. At the appropriate time, the EVAP canis-
ter purge valve and the EVAP vent solenoid are turned
on, allowing the engine to draw a small vacuum on the
entire EVAP system. After the desired vacuum level has
been achieved, the EVAP canister purge valve is turned
OFF, sealing the system. If a sufficient vacuum level
cannot be achieved, a large leak is indicated. This can
be caused by the following conditions :
Missing or faulty fuel cap.
Disconnected or faulty fuel tank pressure sensor.
Disconnected, damaged, pinched, or blocked EVAP
purge line.
Disconnected or faulty EVAP canister purge valve.
Disconnected or faulty EVAP vent solenoid.Open ignition feed circuit to the EVAP vent or purge so-
lenoid.
Damaged EVAP canister.
Leaking fuel sensor assembly O-ring.
Leaking fuel tank or fuel filler beck.
Any of the above conditions can set DTC P0444.
The test is failed if the tank vacuum is less than 10 in
H20 for 15 seconds and the manifold vacuum integral is
greater than 49512 (proportional to purge mass from the
tank).
Conditions for Setting the DTC
Intake Air Temperature(IAT) is between 4°C and
34°C(39°F and 93°F).at engine start up.
Engine Coolant Temperature(ECT) is between 4°C
and 34°C(39°F and 93°F).at engine start up.
Barometric pressure (BARO) is greater than 68kPA.
IAT is not more than 8°C(46°F) greater than the ECT
at start up.
Fuel level is between 10% and 90%.
The throttle position (TP) sensor is less than or equal
to 100%.
No fuel slosh, and the change in fuel level percent is
21 counts on 0.125 sec.
Manifold vacuum is greater than or equal to 10kPA.
Fuel level or change in tank pressure is less than or
equal to 24.9 in H2O.
System voltage is between 11V and 16V.
Page 312 of 1184
1F–214 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F240
DIAGNOSTIC TROUBLE CODE (DTC) – P0445 EVAP PURGE CONTROL
CIRCUIT FAULT
Circuit Description
The evaporative emission (EVAP) system includes the
following components :
Fuel tank.
EVAP vent solenoid.
Fuel tank pressure sensor.
Fuel pipes and hoses.
Fuel vapor lines.
Fuel cap.
EVAP canister.
Purge lines.
EVAP canister purge valve.
EVAP service port.
The evaporative emission system is checked by apply-
ing vacuum to the EVAP system and monitoring for a
vacuum decay. The engine control module(ECM) moni-
tors the vacuum level through the fuel tank pressure
sensor signal. At the appropriate time, the EVAP canis-
ter purge valve and the EVAP vent solenoid are turned
on, allowing the engine to draw a small vacuum on the
entire EVAP system. After the desired vacuum level has
been achieved, the EVAP canister purge valve is turned
OFF, sealing the system. If a sufficient vacuum level
cannot be achieved, a large leak is indicated. This can
be caused by the following conditions :
Missing or faulty fuel cap.
Disconnected or faulty fuel tank pressure sensor.
Disconnected, damaged, pinched, or blocked EVAP
purge line.
Disconnected or faulty EVAP canister purge valve.Disconnected or faulty EVAP vent solenoid.
Open ignition feed circuit to the EVAP vent or purge so-
lenoid.
Damaged EVAP canister.
Leaking fuel sensor assembly O-ring.
Leaking fuel tank or fuel filler beck.
Any of the above conditions can set DTC P0445.
The test is failed if the tank vacuum is less than 10 in
H20 for 15 seconds and the manifold vacuum integral is
greater than 49512 (proportional to purge mass from the
tank).
Conditions for Setting the DTC
Intake Air Temperature(IAT) is between 4°C and
34°C(39°F and 93°F).at engine start up.
Engine Coolant Temperature(ECT) is between 4°C
and 34°C(39°F and 93°F).at engine start up.
Barometric pressure (BARO) is greater than 68kPA.
IAT is not more than 8°C(46°F) greater than the ECT
at start up.
Fuel level is between 10% and 90%.
The throttle position (TP) sensor is less than or equal
to 100%.
No fuel slosh, and the change in fuel level percent is
21 counts on 0.125 sec.
Manifold vacuum is greater than or equal to 10kPA.
Fuel level or change in tank pressure is less than or
equal to 24.9 in H2O.
System voltage is between 11V and 16V.
Page 344 of 1184
1F–246 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F070
DIAGNOSTIC TROUBLE CODE (DTC) 0505
IDLE AIR CONTROL VALVE (IACV) CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) controls the air en-
tering into the engine with an Idle Air Control (IAC)
Valve. To increase the idle rpm, the ECM commands the
pintle inside the IAC valve away from the throttle body
seat. This allows more air to bypass through the throttle
blade. To decrease the rpm the ECM commands the
pintle towards the throttle body seat. This reduces the
amount of air bypassing the throttle blade. A scan tool
will read the IAC valve pintle position in counts. The
higher the counts, the more air that is allowed to bypass
the throttle blade. This Diagnostic Trouble Code (DTC)
determines if a low idle condition exists as defined as
100 rpm below the desired idle rpm.
Conditions for Setting the DTC
No intrusive tests are active.
DTC(s) P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P1133, P1134, P0171, P1171, P0172, P0201,
P0202, P0203, P0204, P0300, P0336, P0337,
P0341, P0342, P0351, P0352, P0402, P0404,
P1404, P0405, P0406, P0443, and P0502 are not
set.
Engine is running more than 60 seconds.
Barometric Pressure (BARO) is greater than 72 kPa
(10.4 psi).
Engine Coolant Temperature (ECT) is greater than
60C (140F).
Ignition voltage is between 11 and 16 volts.
The Intake Air Temperature (IAT) is greater than
–20C (–4F).
Manifold Absolute Pressure is less than 60 kPa (8.7
psi).IAC valve is controlled fully opened.
All of the above must be met for greater than 5 sec-
onds.
Action Taken When the DTC Sets
The Malfunction Indicator Lamp (MIL) will illuminate.
The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.
A history DTC is stored.
Conditions for Clearing the MIL/DTC
The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
A history DTC will clear after 40 consecutive warm-up
cycles without a fault.
DTC(s) can be cleared by using the scan tool.
Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
Inspect the IAC valve electrical connection for proper
mating.
Inspect the wiring harness for damage.
Inspect the throttle stop screw for signs of tampering.
Inspect the throttle linkage for signs of binding or exces-
sive wear.
A slow or unstable idle may be caused by one of the fol-
lowing conditions:
Fuel system too rich or too lean.
Foreign material in the throttle body bore or in the air
induction system.
A leaking or restricted intake manifold.
Page 378 of 1184
1F – 280 ENGINE CONTROLS
DAEWOO M-150 BL2
SYMPTOM DIAGNOSIS
IMPORTANT PRELIMINARY CHECKS
Important: Several symptom procedures call for a care-
ful visual/physical inspection. Always perform the visual/
physical test first. Visual inspections may lead tocorrecting a problem without further checks and can
save valuable time.
StepActionValue(s)YesNo
1
Perform the On-Board Diagnostic (EOBD) System
Check.
Are any Diagnostic Trouble Code(s) (DTCs) stored
in the Engine Control Module (ECM) memory?
–Go to
Appropriate
DTC Table
Go to Step 2
2
1. Inspect all of the ECM ground connections.
2. Inspect all of the vacuum hoses for splits, kinks,
and proper connections.
3. Check for air leaks at all of the mounting areas of
the intake manifold sealing surfaces.
4. Inspect the ignition wires for cracking, hardness,
proper routing, and carbon tracking.
5. Inspect the wiring for proper connections,
pinches, and cuts.
Are all checks complete?
–
Go to
Appropriate
Symptom Table
–
Page 381 of 1184
ENGINE CONTROLS 1F–283
DAEWOO M-150 BL2
HARD START
Definition: The engine cranks OK, but does not start for
a long time. The engine eventually runs or may start and
immediately die.Important: Ensure that the driver is using the correct
starting procedure. Before diagnosing, check service
bulletins for updates.
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Connect the scan tool to the Data Link Connector
(DLC).
2. Check the Engine Coolant Temperature (ECT)
sensor and the Intake Air Temperature (IAT)
sensor using the scan tool.
3. Compare the coolant temperature and the IAT
with the ambient temperature when the engine is
cold.
Do the ECT and the IAT readings differ from the
ambient temperature by more than the value
specified?
3C (5F)Go to Step 3Go to Step 4
3
1. Measure the resistance of the ECT sensor and
the IAT sensor.
2. Compare the resistance value to specifications
using the Temperature Vs. Resistance tables for
DTCs P0118 and P0113.
3. If the resistance is not the same, replace the
faulty sensor.
Is the repair complete?
–
System OK
–
4
1. Check for a sticking throttle shaft or a binding
linkage that may cause a high Throttle Position
(TP) sensor voltage. Repair or replace as
needed.
2. Check the TP sensor voltage reading with the
throttle closed.
Does the voltage measure within the value
specified?
0.4–0.8 VGo to Step 5Go to Step 26
5
1. Check the Manifold Absolute Pressure (MAP)
sensor response and accuracy.
2. Replace the MAP sensor as needed.
Is the repair complete?
–
System OKGo to Step 6
6
Check the fuel pump operation.
Does the fuel pump operate for the specified time
when the ignition switch is turned ON?
2 secGo to Step 7
Go to “Fuel
Pump Relay
Circuit Check”
7Check the fuel system pressure.
Is the fuel pressure within the specifications?380 kPa
(55 psi)
Go to Step 8Go to Step 27
8Check for water contamination in the fuel.
Is fuel contaminated?–Go to Step 9Go to Step 10
9Replace the contaminated fuel.
Is the repair complete?–System OK–