tire type DAEWOO MATIZ 2003 Service Repair Manual

ENGINE CONTROLS 1F–9
DAEWOO M-150 BL2
appropriate wiring diagram. Refer to “ECM Wiring Dia-
grams” in this Section.
9591
Terminal 49GroundOpen
STRATEGY-BASED DIAGNOSTICS
Strategy-Based Diagnostics
The strategy-based diagnostic is a uniform approach to
repair all Electrical/Electronic (E/E) systems. The diag-
nostic flow can always be used to resolve an E/E system
problem and is a starting point when repairs are neces-
sary. The following steps will instruct the technician on
how to proceed with a diagnosis:
Verify the customer complaint. To verify the customer
complaint, the technician should know the normal op-
eration of the system.

Perform preliminary checks as follows:

Conduct a thorough visual inspection.

Review the service history.

Detect unusual sounds or odors.

Gather Diagnostic Trouble Code (DTC) information to
achieve an effective repair.

Check bulletins and other service information. This
includes videos, newsletters, etc.

Refer to service information (manual) system
check(s).

Refer to service diagnostics.
No Trouble Found
This condition exists when the vehicle is found to oper-
ate normally. The condition described by the customer
may be normal. Verify the customer complaint against
another vehicle that is operating normally. The condition
may be intermittent. Verify the complaint under the con-
ditions described by the customer before releasing the
vehicle.
Re-examine the complaints.
When the complaints cannot be successfully found or
isolated, a re-evaluation is necessary. The complaint
should be re-verified and could be intermittent as de-
fined in “intermittents,” or could be normal.
After isolating the cause, the repairs should be made.
Validate for proper operation and verify that the symp-
tom has been corrected. This may involve road testing
or other methods to verify that the complaint has re-
solved under following conditions:

Conditions noted by the customer.

If a DTC was diagnosed, verify the repair be duplicat-
ing conditions present when the DTC was set as
noted in Failure Records or Freeze Frame data.
Verifying Vehicle Repair
Verification of the vehicle repair will be more compre-
hensive for vehicles with Euro On-Board Diagnostic
(EOBD) system diagnostics. Following a repair, the
technician should perform the following steps:
Important: Follow the steps below when you verify re-
pairs on EOBD systems. Failure to follow these steps
could result in unnecessary repairs.

Review and record the Failure Records and the
Freeze Frame data for the DTC which has been diag-
nosed (Freeze Fame data will only be stored for an A,
B and E type diagnostic and only if the Malfunction
Indicator Lamp has been requested).

Clear the DTC(s).

Operate the vehicle within conditions noted in the
Failure Records and Freeze Frame data.

Monitor the DTC status information for the specific
DTC which has been diagnosed until the diagnostic
test associated with that DTC runs.
EOBD SERVICEABILITY ISSUES
Based on the knowledge gained from Euro On-Board
Diagnostic (OBD) experience in the 1994 and 1995
model years in United Status, this list of non-vehicle
faults that could affect the performance of the Euro On-
Board Diagnostic (EOBD) system has been compiled.
These non-vehicle faults vary from environmental condi-
tions to the quality of fuel used. With the introduction of
EOBD across the entire passenger car, illumination of
the Malfunction Indicator Lamp (MIL) due to a non-ve-
hicle fault could lead to misdiagnosis of the vehicle, in-
creased warranty expense and customer
dissatisfaction. The following list of non-vehicle faults
does not include every possible fault and may not apply
equally to all product lines.
Fuel Quality
Fuel quality is not a new issue for the automotive indus-
try, but its potential for turning on the MIL with EOBD
systems is new.
Fuel additives such as “dry gas” and “octane enhancers”
may affect the performance of the fuel. If this results in
an incomplete combustion or a partial burn, it will set
Diagnostic Trouble Code (DTC) P0300. The Reed Vapor
Pressure of the fuel can also create problems in the fuel
system, especially during the spring and fall months
when severe ambient temperature swings occur. A high
Reed Vapor Pressure could show up as a Fuel Trim
DTC due to excessive canister loading.
Using fuel with the wrong octane rating for your vehicle
may cause driveability problems. Many of the major fuel
companies advertise that using “premium” gasoline will
improve the performance of your vehicle. Most premium

ENGINE CONTROLS 1F–15
DAEWOO M-150 BL2
made to enter DTC numbers for tests which the diag-
nostic executive does not recognize, the requested in-
formation will not be displayed correctly and the scan
tool may display an error message. The same applies to
using the DTC trigger option in the Snapshot mode. If an
invalid DTC is entered, the scan tool will not trigger.
Failed Last Test
This message display indicates that the last diagnostic
test failed for the selected DTC. For type A, B and E
DTCs, this message will be displayed during subse-
quent ignition cycles until the test passes or DTCs are
cleared. For type C and type D DTCs, this message will
clear when the ignition is cycled.
Failed Since Clear
This message display indicates that the DTC has failed
at least once within the last 40 warm-up cycles since the
last time DTCs were cleared.
Failed This Ig. (Failed This Ignition)
This message display indicates that the diagnostic test
has failed at least once during the current ignition cycle.
This message will clear when DTCs are cleared or the
ignition is cycled.
History DTC
This message display indicates that the DTC has been
stored in memory as a valid fault. A DTC displayed as a
History fault may not mean that the fault is no longer
present. The history description means that all the con-
ditions necessary for reporting a fault have been met
(maybe even currently), and the information was stored
in the control module memory.
MIL Requested
This message display indicates that the DTC is currently
causing the MIL to be turned ON. Remember that only
type A B and E DTCs can request the MIL. The MIL re-
quest cannot be used to determine if the DTC fault con-
ditions are currently being experienced. This is because
the diagnostic executive will require up to three trips dur-
ing which the diagnostic test passes to turn OFF the
MIL.
Not Run Since CI (Not Run Since Cleared)
This message display indicates that the selected diag-
nostic test has not run since the last time DTCs were
cleared. Therefore, the diagnostic test status (passing
or failing) is unknown. After DTCs are cleared, this mes-
sage will continue to be displayed until the diagnostic
test runs.
Not Run This Ig. (Not Run This Ignition)
This message display indicates that the selected diag-
nostic test has not run during this ignition cycle.
Test Ran and Passed
This message display indicates that the selected diag-
nostic test has done the following:
Passed the last test.

Run and passed during this ignition cycle.

Run and passed since DTCs were last cleared.
If the indicated status of the vehicle is “Test Ran and
Passed” after a repair verification, the vehicle is ready to
be released to the customer.
If the indicated status of the vehicle is “Failed This Igni-
tion” after a repair verification, then the repair is incom-
plete and further diagnosis is required.
Prior to repairing a vehicle, status information can be
used to evaluate the state of the diagnostic test, and to
help identify an intermittent problem. The technician can
conclude that although the MIL is illuminated, the fault
condition that caused the code to set is not present. An
intermittent condition must be the cause.
PRIMARY SYSTEM-BASED
DIAGNOSTICS
There are primary system-based diagnostics which
evaluate the system operation and its effect on vehicle
emissions. The primary system-based diagnostics are
listed below with a brief description of the diagnostic
function:
Oxygen Sensor Diagnosis
The fuel control oxygen sensor (O2S) is diagnosed for
the following conditions:

Few switch count (rich to lean or lean to rich).

Slow response (average transient time lean to rich or
rich to lean).

Response time ratio (ratio of average transient time
rich(lean) to lean(rich)).

Inactive signal (output steady at bias voltage approxi-
mately 450 mV).

Signal fixed high.

Signal fixed low.
The catalyst monitor heated oxygen sensor (HO2S) is
diagnosed for the following conditions:

Heater performance (current during IGN on).

Signal fixed low during steady state conditions or
power enrichment (hard acceleration when a rich mix-
ture should be indicated).

Signal fixed high during steady state conditions or de-
celeration mode (deceleration when a lean mixture
should be indicated).

Inactive sensor (output steady at approx. 438 mV).
If the O2S pigtail wiring, connector or terminal are dam-
aged, the entire O2S assembly must be replaced. Do
not attempt to repair the wiring, connector or terminals.
In order for the sensor to function properly, it must have
clean reference air provided to it. This clean air refer-
ence is obtained by way of the O2S wire(s). Any attempt
to repair the wires, connector or terminals could result in

TIRES AND WHEELS 2E–3
DAEWOO M-150 BL2
Hydroplaning
The condition of driving a vehicle fast on the road surface
covered with water can cause tires to fail to rotate with a
good contact on the surface, so results in remaining them
afloat. This is so–called hydroplaning. It causes brake
failure, lower tractive force, and losing the steering per-
formance so it is very vulnerable condition.
D16A005A
Standing Wave
During running the rotating tire repeats deformation and
restoring movement generated in tread. But when the
wheel rotating speed reaches high, the next deformation
applied to tire before restoring last deformation so the
trembling wave appears in the tread portion. The lower
the tire pressure the severe the trembling wave appears.
And during the high speed.
D106A004
REPLACEMENT TIRES
A Tire Performance Criteria (TPC) specification number
is molded in the sidewall near the tire size of all original
equipment tires. This specification number assures that
the tire meets performance standards for traction, en-
durance, dimensions, noise, handling and rolling resist-
ance. Usually a specific TPC number is assigned to
each tire size.Caution: Do not mix different types of tires on the
same vehicle such as radial, bias and bias-belted
tires except in emergencies, because vehicle han-
dling may be seriously affected and may result in
loss of control.
Caution: Do not change 145/70 R13 tires or 155/65
R13 tires for 175/60 R13 tires, because vehicle
hancling may be seriously affected and may result
in loss of control. If you change 145/70 R13 tires or
155/65 R13 tires for 175/60 R13 tires, you have to
change the steering gear assembly.
Use only replacement tires with the same size, load
range, and construction as the original. The use of any
other tire size or construction type may seriously affect
ride, handling, speedometer/odometer calibration, ve-
hicle ground clearance, and tire clearance to the body
and the chassis. This does not apply to the spare tire fur-
nished with the vehicle.
It is recommended that new tires be installed in pairs on
the same axle.
If it is necessary to replace only one tire, pair it with the
tire having the most tread to equalize the braking action.
Although they may appear different in tread design, tires
built by different manufacturers with identical TPC speci-
fications may be used on the same vehicle.
ALL SEASON TIRES
Most vehicles are now equipped with steel-belted all
season radial tires as standard equipment. These tires
qualify as snow tires, with a 37 percent higher average
rating for snow traction than the non-all season radial
tires previously used. Other performance areas, such as
wet traction, rolling resistance, tread life, and air reten-
tion, have also been improved. This was done by im-
provements in both tread design and tread compounds.
These tires are identified by an “M + S” molded in the tire
sidewall following the size number. The suffix “MS” is
also molded in the sidewall after the TPC specification
number.
The optional handling tires used on some vehicles are
not all season tires. These will not have the “MS” mark-
ing after the tire size or the TPC specification number.
TIRE LABEL
The tire label is permanently located on the rear face of
the driver’s door and should be referred to for tire infor-
mation. It lists the maximum vehicle load, the tire size
(including the spare tire), and the cold inflation pressure
(including the spare tire).
SPARE TIRE
This vehicle comes equipped with a full-sized spare tire
and wheel.

2E –4 TIRES AND WHEELS
DAEWOO M-150 BL2
WHEELS
Wheels must be replaced if they are bent, dented, have
excessive lateral or radial runout, leak air through welds,
have elongated bolt holes, or if the wheel bolts won’t
stay tight or are heavily rusted. Wheels with excessive
runout may cause vehicle vibration. Replacement
wheels must be equivalent to the original equipment
wheels in load capacity, diameter, rim width, offset, and
mounting configuration. A wheel of improper size or type
may affect wheel and bearing life, brake cooling,
speedometer/odometer calibration, vehicle ground
clearance, and tire clearance to the body and the chas-
sis.
INFLATION OF TIRES
The pressure recommended for any vehicle line is care-
fully calculated to give a satisfactory ride, handling,
tread life, and load-carrying capacity.
Tire pressure should be checked monthly or before any
extended trip. Check the tires when they are cold, after
the vehicle has sat for 3 hours or more or has been driv-
en less than 1 mile. Set the tire pressure to the specifi-
cations on the tire label located on the rear face of the
driver’s door. Tire inflation pressure is also given under
“Tire Size and Pressure Specifications” in this section.
Valve caps or extensions should be on the valves to
keep dust and water out.
Higher than recommended tire pressure can cause:

Hard ride

Tire bruising or damage

Rapid tread wear at the center of the tire
Lower than recommended pressure can cause:

Tire squeal on turns

Hard steering

Rapid and uneven wear on the edges of the tread

Tire rim bruises and rupture

Tire cord breakage

High tire temperatures
Unequal tire pressures on same axle can cause:

Uneven braking

Steering lead
Reduced handling

Swerve on acceleration

Torque steer
ROTATION TIRES
Front and rear tires perform different jobs and can wear
differently depending on the tires of road driven, driving
habit, etc.
The front tires will wear faster than the rear ones.
To avoid uneven wear of tires and to prolong tire life, in-
spect and rotate the tires every 5,000 km (3,100 miles).
After rotating the tires, adjust the tire inflation pressures
and be sure to check wheel nuts tightness.
D16A304A
WHEEL BALANCE
Balance is the easiest procedure to perform and should
be done first if the vibration occurs at high speeds, or if
the tires or the wheels are replaced.
When proceeding the wheel balancing procedure regard
the belows.
1. Do not use the wheel weight over two at the inboard
and the outboard flanges.
2. The total weight of the wheel weights should not ex-
ceed the 100 grams (3.5 ounces).
3. Blanching the assemblies with factory aluminum
wheels requires the use of special nylon–coated,
clip–on wheel weights.

2E –8 TIRES AND WHEELS
DAEWOO M-150 BL2
D16A503A
90–11 0 Nm
Installation Procedure
Notice: Before installing the wheels, remove any build-
up of corrosion on the wheel mounting surface and the
brake drum or the rotor mounting surface by scraping
and brushing them with a wire brush. Installing the
wheels without good metal-to-metal contact at the
mounting surfaces can cause the wheel nuts to loosen,
which can later allow a wheel to come off while the ve-
hicle is moving. Wheel nuts must be tightened in se-
quence and to the proper torque to avoid bending the
wheel, the brake drum or the rotor.
1. Mount the wheel.
2. Install the wheel nuts in the diagonally. Do not tighten
the wheel nuts.
3. Lower the vehicle.
Tighten
Tighten the wheel nuts to 90–110 Nm (66–81 lb-ft).
ON-VEHICLE BALANCING
On-vehicle balancing will help correct vibrations due to
brake drum, rotor, and wheel cover imbalances.
Notice: Do not allow the front suspension to hang free.
When the drive axle is run at an extreme angle, extra
vibrations can occur, as well as damage to seals and
joints.
1. During on-vehicle balancing, do not remove the bal-
ance weights from the off-vehicle dynamic balance.
2. If more than 1 ounce of additional weight is required,
split the weight between the inner and the outer rim
flanges.
3. Spin the driven tire and wheel assemblies using the
engine.
OFF-VEHICLE BALANCING
Perform wheel balancing with an electronic off-vehicle
balancer. The balancer is easy to use and gives both a
static and a dynamic balance. Unlike on-vehicle balanc-
ing, the off-vehicle balancer does not correct for drum or
rotor imbalance. This drawback is overcome by its accu-
racy. Secure the wheel on the balancer with a cone
through the back side of the centerhole, not through the
wheel nut holes.
CORRECTING NON-UNIFORM TIRES
There are two ways to correct properly balanced tires
which still vibrate. One method uses an automatic
machine which loads the tire and buffs small amounts of
rubber from high spots on the outer two tread rows.
Correction by this method is usually permanent and, if it
is done properly, does not significantly affect the
appearance or the tread life of the tire. Tire truing with a
blade-type machine is not recommended because it
substantially reduces the tread life and often does not
correct the problem permanently.

POWER STEERING GEAR 6C–13
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescription
Power Steering FluidPower Steering Fluid DEXRON-II or DEXRON-III
Capacity1.0 L (1.056 qt)
TypeRack and Pinion
Overall Gear Ratio15.7 : 1
Power Steering Angle144, 155Inside39.5± 2
TireOutside33.5± 2
175 TireInside34.9± 2
Outside30.5± 2
GreaseRackPOLYUREAS
Ball JointSYNTHETICS OILS & LI SOAPS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Power Steering Gear Bracket Bolt50–5536–41–
Power Steering Gear Pinion Nut40–5030–36–
Power Steering Gear Pinion Dust Cover45–5533–41–
Power Steering Gear Pressure Line Fitting25–3518–25–
Power Steering Oil Pressure Pipe Fitting (Gear Side)21–3516–25–
Power Steering Gear Ajuster PlugRefer to “DIAGNOSIS” in this section.

MANUAL STEERING GEAR 6D–17
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Description
Type Rack and Pinion
Overall Gear Ratio 21 : 1
Inside39.5 ± 2 145,155 Tire
Outside

33.5 ± 2 Steering Angle Inside 34.9 ± 2 175 Tire Outside 30.5 ± 2 Rack Gear POLYUREAS Lubricant Ball Joint SYNTHETICS OILS & LI SOAPS Locktite Type DAC SPEC ADHESIVE SEALANT #520414
FASTENER TIGHTENING SPECIFICATIONS
Application Nm Lb-Ft Lb-In Tie Rod End Castellated Nut 30 – 55 21 – 41 – Tie Rod End Lock Nut 35 – 55 25 – 41 – Steering Gear Bracket Bolts 50 – 55 36 – 41 – Tie Rod–to–Rack Gear 80 – 120 59 – 89 – Pinion Plug 40 – 60 30 – 44 – Pinion Preload Refer to “Diagnosis” in this section.