warning DAEWOO MATIZ 2003 Service Repair Manual

DAEWOO M-150 BL2
SECTION 4A
HYDRAULIC BRAKES
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 4A-2. . . . . . . . . . . . . . . . . .
Warning Lamp Operation 4A-2. . . . . . . . . . . . . . . . . . .
Component Locator 4A-3. . . . . . . . . . . . . . . . . . . . . . . .
Brake System (Non-ABS) 4A-3. . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 4A-4. . . . .
Brake System Testing 4A-4. . . . . . . . . . . . . . . . . . . . . .
Brake Hose Inspection 4A-4. . . . . . . . . . . . . . . . . . . . .
Warning Lamp Operation 4A-5. . . . . . . . . . . . . . . . . . .
Brake System Fault 4A-5. . . . . . . . . . . . . . . . . . . . . . . .
Manual Bleeding the Brakes 4A-6. . . . . . . . . . . . . . . .
Pedal Travel Check 4A-6. . . . . . . . . . . . . . . . . . . . . . . .
Brake Pedal Free Play Inspection 4A-7. . . . . . . . . . . Repair Instructions 4A-8. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 4A-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Hose (Front) 4A-8. . . . . . . . . . . . . . . . . . . . . . . .
Brake Hose (Rear) 4A-9. . . . . . . . . . . . . . . . . . . . . . . .
Stoplamp Switch 4A-9. . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Pedal 4A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 4A-13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications 4A-13. . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 4A-13. . . . . . . . . .
Schematic and Routing Diagrams 4A-14. . . . . . . . . .
Brake Lamp Warning Circuit 4A-14. . . . . . . . . . . . . . .
Stoplamp Switch Circuit 4A-14. . . . . . . . . . . . . . . . . . .

4A – 2 HYDRAULIC BRAKES
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located
in the instrument panel cluster. When the ignition switch
is in the III position, the BRAKE warning lamp should il-
luminate. It should go off when the ignition switch return
to II position. The following conditions will activate the
BRAKE warning lamp.

The lamp should be on whenever the parking brake
applied and the ignition switch is in the II position.

A low fluid level in the master cylinder will turn the
BRAKE warning lamp on.
D17A007A

HYDRAULIC BRAKES 4A–5
DAEWOO M-150 BL2
WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located
in the instrument panel cluster. When the ignition switch
is in the III position, the BRAKE warning lamp should
glow and then go OFF when the ignition switch returns
to the II position.The following conditions will activate the BRAKE lamp:

Parking brake applied. The light should be on when-
ever the parking brake is applied and the ignition
switch is II.

Low fluid level. A low fluid level in the master cylinder
will turn the BRAKE lamp ON.
BRAKE SYSTEM FAULT
Condition Probable cause Correction
Brake Warning Lamp ON
Brake fluid leaks.
Repair the leaks or add th fluid.

Parking brake switch shorted to
ground.
Repair the short ground.

Faulty the fluid level sensor.
Replace the sensor.
Stoplamp ON
Faulty the stoplamp switch.
Replace the stoplamp switch.

Push rod length is short.
Adjust the push rod length of the
power booster.

Stoplamp switch circuit shorted to
battery.
Repair or Replace the wiring harness.
Poor Braking
Brake fluid lacks or leaks.
Repair the leaks or add the fluid.

Brake fluid contamination.
Replace the fluid.

Air in the brake system.
Bleed the brake system.

Damaged brake lines.
Replace the brake lines.

Damaged vacuum hose or faulty
check valve.
Replace the vacuum hose or check
value.
Dragging Brake
No free play at the brake pedal.
Adjust the free play.

Weakened the brake pedal return
spring.
Replace the return spring.

Faulty master cylinder.
Replace the master cylinder.

Air in the brake system.
Bleed the brake system.
Pedal Over Stroke
Brake fluid lacks or leaks.
Repair the leaks or add the fluid.

Poor adjustment of the brake pedal
free play.
Adjust the push rod length of the
power booster.

4A –14 HYDRAULIC BRAKES
DAEWOO M-150 BL2
SCHEMATIC AND ROUTING DIAGRAMS
BRAKE LAMP WARNING CIRCUIT
D17A201B
STOPLAMP SWITCH CIRCUIT
D17A202B

ANTILOCK BRAKE SYSTEM 4F–5
DAEWOO M-150 BL2
D107E001
WHEEL SPEED SENSORS AND
RINGS
Front wheel speed sensors are installed to the front
knuckle and rear wheel speed sensors are installed to
the backing plate.
Wheel speed sensors are no serviceable. And the air
cap is not adjusted. Front wheel speed sensor ring is
pressed onto the drive axle shaft. Each ring contains 40
equally spaced teeth. Exercise care during service pro-
cedures to avoid prying or contacting this ring. Exces-
sive contact may cause damage to one or more teeth.
Rear wheel speed sensor rings are incorporated into the
hub drum.
D107E007
D107E008
ELECTRONIC BRAKE DISTRIBUTION
ABS features an enhanced algorithm which includes
control of the brake force distribution between the front
and rear axles. This is called Electronic Brake Distribu-
tion or Dynamic Rear Proportioning valve. In an unladen
car condition the brake efficiency is comparable to the
conventional system but for a fully loaden vehicle the ef-
ficiency of the Dynamic Rear Proportioning System is
higher due to the better use of rear axle braking capabili-
ty.
No indication is given to the driver when Dynamic Rear
Proportioning is activated. Also, DRP remains active
even in such cases where the anti-lock function of the
ABS is disabled.
D17E009A
Critical Brake Points
Ideal Distribution
Fully Laden Vehicle
Ideal Distribution
Lightly Loaded
Vehicle
Advanced Distribution with ABS
Regular Distribution without Dynamic
Rear Proportioning
Relative Front Brake Force
INDICATOR
It illuminates for four seconds immediately after the igni-
tion has been turned on to show that the anti-lock sys-
tem self-test is being carried out. If the light does not go
off after this time it means that there may be a problem
and ABS operation is not available.
If any malfunction or error, including an unplugged
EBCM connector, is detected during vehicle operation,
the light will come on, warning the driver that the ABS is
not operative and brake operation is in conventional,
non-ABS mode.
D17E010A

4F–6 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
EBCM CONNECTOR
A Connector has 31 pins which are shown below figure.
And a connector includes a warning switch which
grounds and lights the ABS warning lamp if there is No
EBCM unit plugged in, so that an indication is given that
ABS is not available.
D17E011A
Mechanical Switch

4F–12 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
VISUAL IDENTIFICATION
EBCM CONNECTOR FACE VIEW
Terminal 9 is identified as they appear from the wire entry end of the harness connector.
EBCM Connector
D107E204
 
 Pin
 
 Signal Name
 
 Color
 
 Circuit
 2 ROUGH ROAD GRY/YEL Buffered Wheel Speed Signal : to ECM–55
(Sirius D3)
 
9
 
RRWSHI
 
BRN
 
Right Rear Wheel Speed High 
 10
 
 RRWSLO
 
 WHT
 
 Right Rear Wheel Speed Low
 11 SDLUART BRN/DK GRN Serial Data Link
 12 RFWSHI DK GRN/BLK Right Front Wheel Speed High
 13 RFWSLO BRN/DK GRN Right Front Wheel Speed Low
 14 LFWSHI DK BLU Left Front Wheel Speed High
 15 IGN RED/YEL Switched Ignition
 16 GND BLK Negative Battery Terminal 17 BATT RED Battery 18 BATT RED Battery 
 19
 
 GND
 
 BLK
 
 Negative Battery Terminal
 20 ABSWARN DK GRN/GRY ABS Warning Indicator
 22 LRWSHI BLK Left Rear Wheel Speed High
 23 LRWSLO RED Left Rear Wheel Speed Low
 24 BRAKESW YEL Brake Switch
 25 LFWSLO YEL Left Front Wheel Speed Low

4F–16 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
D17E301A
DIAGNOSTIC TROUBLE CODE (DTC) 0354
LEFT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED
Circuit Description
As a toothed ring passes by the wheel speed sensor,
changes in the electromagnetic field cause the wheel
speed sensor to produce a sinusoidal (AC) voltage sig-
nal whose frequency is proportional to the wheel speed.
The magnitude of this signal is directly related to wheel
speed and the proximity of the wheel speed sensor to
the toothed ring often referred to as the air gap.
Diagnosis
This test detects a short to battery, ground, or open in
the left front wheel speed sensor circuit.
Cause(s)

The wheel speed circuit is open or shorted to the bat-
tery or ground.

There is a loose connection in the wheel speed cir-
cuit.

The wheel speed sensor resistance is very high.

The EBCM is malfunctioning.Fail Action
This is a critical operational fault. The ABS is disabled
and the ABS warning lamp is turned on. The proportion-
ing is operation.
Diagnostic Aids
An ‘‘intermittent’’ malfunction may be caused by a poor
connection, rubbed through wire insulation, or a wire
that is broken inside the insulation.
Thoroughly check any circuitry suspected of causing the
intermittent complaint. Look for backed out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, poor terminal to wiring connections,
or physical damage to the wiring harness.
Wheel speed sensor resistance will increase as the sen-
sor temperature increases.
When replacing a wheel speed sensor, inspect the sen-
sor terminals and harness connector for corrosion and/
or water intrusion. If evidence of corrosion or water

4F–20 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
D17E301A
DIAGNOSTIC TROUBLE CODE (DTC) 0355
LEFT FRONT WHEEL SPEED SENSOR POOR
AIR GAP OR MISSING TOOTH RING
Circuit Description
As a toothed ring passes by the wheel speed sensor,
changes in the electromagnetic field cause the wheel
speed sensor to produce a sinusoidal (AC) voltage sig-
nal whose frequency is proportional to the wheel speed.
The magnitude of this signal is directly related to wheel
speed and the proximity of the wheel speed sensor to
the toothed ring often referred to as the air gap.
Diagnosis
This test checks for the left front wheel speed equal to 0
km/h (0 mph) for greater than 6 km/h (3.8 mph).
Cause(s)

The tooth ring is missing.

The air gap exceeds the required specifications.
Fail Action
This is a critical operational fault. The ABS is disabled
and the ABS warning lamp is turned on. The proportion-
ing is operation.Diagnostic Aids
An ‘‘intermittent’’ malfunction may be caused by a poor
connection, rubbed through wire insulation, or a wire
that is broken inside the insulation.
Thoroughly check any circuitry suspected of causing the
intermittent complaint. Look for backed out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, poor terminal to wiring connections,
or physical damage to the wiring harness.
Wheel speed sensor resistance will increase as the sen-
sor temperature increases.
When replacing a wheel speed sensor, inspect the sen-
sor terminals and harness connector for corrosion and/
or water intrusion. If evidence of corrosion or water
intrusion exists, replace the wheel speed sensor har-
ness. If replacing a wheel speed sensor harness, in-
spect the sensor terminals. If you find evidence of
corrosion or water intrusion, replace the wheel speed

4F–22 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
D17E301A
DIAGNOSTIC TROUBLE CODE (DTC) 0356
LEFT FRONT WHEEL SPEED SENSOR CIRCUIT
INTERMITTENT SHORTED
Circuit Description
As a toothed ring passes by the wheel speed sensor,
changes in the electromagnetic field cause the wheel
speed sensor to produce a sinusoidal (AC) voltage sig-
nal whose frequency is proportional to the wheel speed.
The magnitude of this signal is directly related to wheel
speed and the proximity of the wheel speed sensor to
the toothed ring often referred to as the air gap.
Diagnosis
This test intermittent the left front wheel speed sensor
circuit.
Cause(s)

The wheel speed sensor is intermittent shorted to the
battery or ground.

There is a loose connection in the wheel speed sen-
sor circuit.

There is a loose connection in the EBCM.

The EBCM is malfunctioning.Fail Action
This is a critical operational fault. The ABS is disabled
and the ABS warning lamp repeat intermittent turned on,
and off. The proportioning is operation.
Diagnostic Aids
An ‘‘intermittent’’ malfunction may be caused by a poor
connection, rubbed through wire insulation, or a wire
that is broken inside the insulation.
Thoroughly check any circuitry suspected of causing the
intermittent complaint. Look for backed out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, poor terminal to wiring connections,
or physical damage to the wiring harness.
Wheel speed sensor resistance will increase as the sen-
sor temperature increases.
When replacing a wheel speed sensor, inspect the sen-
sor terminals and harness connector for corrosion and/
or water intrusion. If evidence of corrosion or water