seats DODGE DURANGO 2006 2.G User Guide

WARNING!
Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer’s directions exactly
when installing an infant or child restraint.
Installing Child Restraints Using the Vehicle Seat
Belt
The second and third row seats have either cinching latch
plates or automatic locking retractors which are designed
to keep the lap portion tight around the child restraint so
that it is not necessary to use a locking clip. If the seat belthas a cinching latch plate, pulling up on the shoulder
portion of the lap/shoulder belt will tighten the belt. The
cinching latch plate will keep the belt tight, however, any
seat belt system will loosen with time, so check the belt
occasionally and pull it tight if necessary. If the seat belt
has a automatic locking retractor, it will have a distinctive
label. Pull the belt from the retractor until there is enough
to allow you to pass through the child restraint and slide
the latch plate into the buckle. Then, pull the belt until it
is all extracted from the retractor. Allow the belt to return
to the retractor, pulling on the excess webbing to tighten
the lap portion about the child restraint. Refer toAuto-
matic Locking Modeearlier in this section.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71
2

Child Restraints in Third Row Seating (If
Equipped)
The third seating row is not capable of installing child
restraints that require the use of a tether strap. There are
no tether anchor provisions for the third seating row in
your vehicle, the hooks in the rear floor are not designed
to withstand the forces that may occur during a crash.
WARNING!
An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the
child. Use only the anchor positions directly behind
the child seat to secure a child restraint top tether
strap. Do not install a child restraint that requires a
tether strap in the third seating row (if equipped) of
this vehicle.
Child Restraint Tether Anchor
There are tether strap anchorages behind each seating
position in the second row. For vehicles equipped with
third row seating, there is no Child Tether Anchorage
provided for the third row of seats. To install child
restraint tethers follow these instructions.
1. Place the child restraint in the second row of seats.
2. Route the tether strap under the head restraint and
between the two posts.
3. Attach the tether strap hook of the child restraint to
the tether anchor located on the seat back and remove the
slack in the tether strap according to the manufacturer’s
instructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73
2

Seats................................111
▫Front Seat Manual Seat Adjustment........111
▫Front Seats Manual Seat Recliners..........112
▫Manual Lumbar Support Adjustment — If
Equipped...........................113
▫Adjustable Head Restraints — All Seating
Positions...........................113
▫8 - Way Driver’s Power Seat — If Equipped . . 114
▫4 - Way Passenger’s Power Seat — If
Equipped...........................115
▫Front Heated Seats — If Equipped.........115
▫Second Row 40/20/40 Seat — Fold And
Tumble............................117
▫Third Row Seat Bench — If Equipped.......120▫Third Row 60/40 Folding — If Equipped....122
Driver Memory System — If Equipped.......125
▫Setting Memory Positions And Linking Remote
Keyless Entry Transmitter To Memory.......126
▫Memory Position Recall.................127
▫To Disable A Transmitter Linked To Memory . . 127
▫Self-Limiting Control...................128
▫Driver Easy Exit And Easy Entry Control....128
To Open And Close The Hood.............129
Lights...............................131
▫Interior Lights.......................132
▫Battery Saver........................132
▫Headlight Delay......................133
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

North American English
Primary Alternate(s)
Zero Oh
Add location Add new
All All of them
Confirmation prompts Confirmations prompts
Delete a name Delete
Language Select language
List names List all
List paired phones List phones
Pager Beeper
Phone pairing Pairing
Phonebook Phone book
Return to main menu Return. Main menu
Select phone select
Set up Phone settings phone set
upSEATS
Front Seat Manual Seat Adjustment
The adjusting lever is at the front of the seat, near the
floor. Lift the lever and move the seat to the desired
position. Release the bar to lock the seat into position.
Using body pressure, move forward and rearward on the
seat to be sure the seat adjusters have latched.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111
3

WARNING!
Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
properly adjusted and you could be injured. Adjust
any seat only while the vehicle is parked.
Front Seats Manual Seat Recliners
The bucket seats are equipped with recliners. The reclin-
ing mechanism is operated by a lever located on the right
side of the passenger’s seat and the left side of the driver
seat. To recline, lean forward slightly before lifting the
lever, then push back to the desired position and release
the lever. Lean forward and lift the lever to return the
seatback to its normal position. Using body pressure, lean
forward and rearward on the seat to be sure the seatback
is locked.
Manual Seat Adjuster
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4 - Way Passenger’s Power Seat — If Equipped
The front passenger’s power seat switches are located on
the right side of the passenger seat lower side trim. The
bottom switch controls forward/rearward adjustment.
The top switch controls the seatback recline adjustment.
NOTE:The 4 - way seat does not have an up/down
adjustment.
Front Heated Seats — If Equipped
This feature heats the driver and front passenger seats.
The controls for the front heated seats are located on the
center of the instrument panel, below the climate con-
trols. The heated seat system allows the driver and front
Heated Seat Switches
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115
3

passenger to select from two different levels of supple-
mental electrical seat heating, or no seat heating to suit
their individual comfort requirements.
With the ignition switch in the RUN position, depressing
the heated seat switch rocker to its momentary High or
Low position provides power to the heated seat element
and maintains the requested temperature setting. If the
heated seat switch is depressed to a different position
(Low or High) than the currently selected state, the
requested temperature setting will change to a new
selection. If the heated seat switch is depressed a second
time to the same position as the currently selected state,
the seat heater will turn off.NOTE:The high heat setting will operate for approxi-
mately 30 minutes. After 30 minutes, the system will
automatically transition to the low heat setting. The low
heat setting will operate for 30 minutes, then the system
will turn off.
If the low heat setting is initially selected, the system will
operate for 30 minutes and then turn off.
If the indicator lamp on the heated seat switch does not
light, an indicator blinks when the switch is depressed or
if the heated seats do not operate, the system should be
serviced by a qualified technician.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

WARNING!
Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion or other physical condition must exercise care
when using the seat heater. It may cause burns even
at low temperatures, especially if used for long
periods of time.
Do not place anything on the seat that insulates
against heat, such as a blanket or cushion. This may
cause the seat heater to overheat.
Second Row 40/20/40 Seat — Fold and Tumble
The 40/20/40 seat configuration is standard on all mod-
els. This seat is equipped with a unique fold-and-tumble
feature. The 40% seatbacks have spring loaded hinges
which assist with the folding of the seatbacks.Second row leather seats have seatback recliners at the
40% seating positions. Raising the lever allows the seat-
back to be reclined an additional 11 degrees.
To Fold the 40% seatbacks fully raise the lever on the side
of the seat to release the seatback. The seatback can nowFold, Tumble, and Recline Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117
3

WARNING!
Do not drive the vehicle with the outer 40% second
row seats in the tumbled position. The outer 40%
second row seats are only intended to be tumbled for
entry and exit to the third row seat. Failure to follow
these instructions could result in personal injury.
NOTE:The seatback must be fully folded into the down
position to allow the lever to be raised enough to release
the floor latches.
To Fold and Tumble the 2nd row 40% seats from the 3rd
row, fully raise the lever at the rear of the seat to fold the
seatback. Continue raising the lever to release the floor
latches to tumble the seat.
NOTE:The head restraints must be lowered but do not
have to be removed to fold and tumble the seats.
Tumble Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
3

Third Row Seat Bench — If Equipped
To Fold The Seats
Folding the third seat occurs in two stages: First the
cushion is lifted and moved forward from the pockets at
the front of the cushion. The cushion will rest onto the
floor directly behind the second row seat. Second, the top
of the back is folded forward and rests onto the cushion.
The back will not fold unless the cushion has been folded
forward first.
Seat Cushion Pockets
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE