radio DODGE DURANGO 2017 3.G Owner's Manual

PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED
Your vehicle may be equipped with the ParkView Rear
Back Up Camera that allows you to see an on-screen image
of the rear surroundings of your vehicle whenever the gear
selector is put into REVERSE. The image will be displayed
on the Navigation/Multimedia radio display screen along
with a caution note to “check entire surroundings” across
the top of the screen. After five seconds this note will
disappear. The ParkView camera is located on the rear of
the vehicle above the rear License plate.
When the vehicle is shifted out of REVERSE (with camera
delay turned OFF), the rear camera mode is exited and the
navigation or audio screen appears again.When the vehicle is shifted out of REVERSE (with camera
delay turned ON), the rear view image with dynamic grid
lines will be displayed for up to 10 seconds after shifting
out of
REVERSE unless the forward vehicle speed ex-
ceeds 8 mph (13 km/h), the transmission is shifted into
PARK or the ignition is switched to the OFF position.
NOTE: The ParkView Rear Back Up Camera has program-
mable modes of operation that may be selected through the
Uconnect System. Refer to “Uconnect Settings” in “Under-
standing Your Instrument Panel” for further information.
When enabled, active guide lines are overlaid on the image
to illustrate the width of the vehicle and its projected
backup path based on the steering wheel position. A
dashed center line overlay indicates the center of the
vehicle to assist with parking or aligning to a hitch/
receiver. Different colored zones indicate the distance to
the rear of the vehicle. The following table shows the
approximate distances for each zone:
Zone Distance to the rear of the vehicle
Red 0 - 1 ft (0 - 30 cm)
Yellow 1 ft - 6.5 ft (30 cm - 2 m)
Green 6.5 ft or greater (2 m or greater)
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmission
of the radio-frequency signal, it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system. To erase the channels, place the ignition in the ON/RUN
position and push and hold the two outside HomeLink
buttons (I and III) for up 20 seconds or until the red
indicator flashes.
NOTE:
•
Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manufac-
tured after 1995:
These garage door openers can be identified by the
“LEARN” or “TRAIN” button located where the hanging
antenna is attached to the garage door opener. It is NOT the
button that is normally used to open and close the door.
The name and color of the button may vary by manufac-
turer.
HomeLink Buttons/Sunvisor
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

2. Push and hold the desired HomeLink button until theindicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Program-
ming A Non-Rolling Code” step 2 and follow all remain-
ing steps.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission:
Canadian radio frequency laws require transmitter signals
to time-out (or quit) after several seconds of transmission,
which may not be long enough for HomeLink to pick up
the signal during programming. Similar to this Canadian
law, some U.S. gate operators are designed to time-out in
the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage door
or gate motor.
1. Cycle the ignition to the ON/RUN position. 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)
away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to push and hold the HomeLink button while you push and release (“cycle”) your hand-held trans-
mitter every two seconds until HomeLink has success-
fully accepted the frequency signal. The indicator light
will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds or longer in rare cases. The garage door may
open and close while you are programming.
5. Push and hold the programmed HomeLink button and observe the indicator light.
NOTE: •If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pushed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Once the driver ’s side crossbar is in place, tighten the
thumb screws completely.
Repeat the procedure to stow the second crossbar on the
opposite side.NOTE:
•
To help control wind noise, stow the crossbars in the side
rails when they are not in use.
• If any metallic object is placed over the satellite radio
antenna (if equipped), you may experience interruption
of satellite radio reception.
Tightening Crossbar
Stowed Crossbars
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
INSTRUMENT PANEL FEATURES ...........234
 INSTRUMENT CLUSTER ..................235
 WARNING AND INDICATOR LIGHTS ........237
â–« Red Telltale Indicator Lights ...............238
â–« Yellow Telltale Indicator Lights .............245
â–« Green Telltale Indicator Lights ..............254
â–« White Telltale Indicator Lights ..............257
â–« Blue Telltale Indicator Lights ...............258
 INSTRUMENT CLUSTER DISPLAY ...........259
â–« Instrument Cluster Display Location
And Controls ........................ .259
â–« Engine Oil Life Reset ....................262
â–« Instrument Cluster Display Messages ........263
â–« Instrument Cluster Display Selectable
Menu Items .......................... .264â–«
Screen Setup Driver Selectable Items .........268
â–« Battery Saver On/Battery Saver Mode
Message — Electrical Load Reduction Actions —
If Equipped ......................... .269
 CYBERSECURITY ....................... .271
 UCONNECT SETTINGS ...................273
â–« Buttons On The Faceplate .................273
â–« Buttons On The Touchscreen ...............274
â–« Customer Programmable Features —
Uconnect 5.0 Personal Settings ..............274
â–« Customer Programmable Features —
Uconnect 8.4 Personal Settings ..............293
 UCONNECT RADIOS — IF EQUIPPED ........314
 IPOD/USB/MP3 CONTROL — IF EQUIPPED . . .314
â–« Connecting The iPod Or External USB Device . . .3144

â–«Using This Feature ..................... .315
â–« Second Row USB Charging Port ............315
 UCONNECT REAR SEAT ENTERTAINMENT (RSE)
SYSTEM — IF EQUIPPED .................316
â–« Getting Started ....................... .316
â–« Dual Video Screen ..................... .318
â–« Blu-ray Disc Player ..................... .318
â–« Play Video Games ..................... .320
â–« Play A DVD/Blu-ray Disc Using The
Touchscreen Radio ..................... .321
â–« Important Notes For Dual Video Screen
System ............................. .323
â–« Blu-ray Disc Player Remote Control —
If Equipped .......................... .323
â–« Replacing The Remote Control Batteries .......325
â–« Headphones Operation ...................325
â–« Controls ............................ .325
â–« Replacing The Headphone Batteries ..........326â–«
Unwired Stereo Headphone Lifetime Limited
Warranty ............................ .326
 STEERING WHEEL AUDIO CONTROLS —
IF EQUIPPED ......................... .332
â–« Radio Operation ....................... .333
â–« CD Player ........................... .333
 CD/DVD/BLU-RAY DISC MAINTENANCE . . . .333
 RADIO OPERATION AND MOBILE PHONES . . .334
â–« Regulatory And Safety Information ..........334
 CLIMATE CONTROLS ...................336
â–« Overview ........................... .336
â–« Automatic Temperature Control (ATC) —
If Equipped ......................... .346
â–« Operating Tips ....................... .350
 PERSONALIZED

MENU BAR...............353
 UCONNECT VOICE RECOGNITION
QUICK TIPS .......................... .354
â–« Introducing Uconnect ....................354
232 UNDERSTANDING YOUR INSTRUMENT PANEL

â–«Get Started .......................... .355
â–« Basic Voice Commands ...................356
â–« Radio .............................. .356
â–« Media .............................. .357
â–« Phone .............................. .358
â–« Voice Text Reply ...................... .359
â–« Climate (8.4/8.4 NAV) ...................361
â–« Navigation (8.4 /8.4 NAV) ................362
â–« Uconnect Access (8.4/8.4 NAV) .............363
â–« Register (8.4/8.4 NAV) ...................364 â–«
Vehicle Health Alert ....................364
â–« Mobile App (8.4/8.4 NAV) ................365
â–« Voice Texting (8.4/8.4 NAV) ...............366
â–« Yelp (8.4/8.4 NAV) ..................... .367
â–« SiriusXM Travel Link (8.4/8.4 NAV) ..........368
â–« Siri Eyes Free — If Equipped ..............369
â–« Do Not Disturb ....................... .372
â–« General Information .....................373
â–« Additional Information ...................373
4
UNDERSTANDING YOUR INSTRUMENT PANEL 233

INSTRUMENT PANEL FEATURES
Instrument Panel
1 — Air Outlet6 — Lower Switch Bank
2 — Instrument Cluster 7 — Hazard Switch
3 — Radio 8 — Ignition Start/Stop Button
4 — Glove Compartment 9 — Dimmer Switch
5 — Climate Controls 10 — Headlight Switch
234 UNDERSTANDING YOUR INSTRUMENT PANEL

•The battery was discharged by an electrical load left on
when the vehicle was parked.
• The battery was used for an extended period with the
engine not running to supply radio, lights, chargers,
+12V portable appliances like vacuum cleaners, game
consoles and similar devices.
What to do when an electrical load reduction action message
is present (“Battery Saver On” or “Battery Saver Mode”)
During a trip:
• Reduce power to unnecessary loads if possible:
– Turn off redundant lights (interior or exterior)
– Check what may be plugged in to power outlets +12V, 115V AC, USB ports
– Check HVAC settings (blower, temperature)
– Check the audio settings (volume)
After a trip:
• Check if any aftermarket equipment was installed (ad-
ditional lights, upfitter electrical accessories, audio sys-
tems, alarms) and review specifications if any (load and
Ignition Off Draw currents). •
Evaluate the latest driving cycles (distance, driving time
and parking time).
• The vehicle should have service performed if the mes-
sage is still present during consecutive trips and the
evaluation of the vehicle and driving pattern did not
help to identify the cause.
CYBERSECURITY
Your vehicle may be a connected vehicle and may be
equipped with both wired and wireless networks. These
networks allow your vehicle to send and receive informa-
tion. This information allows systems and features in your
vehicle to function properly.
Your vehicle may be equipped with certain security fea-
tures to reduce the risk of unauthorized and unlawful
access to vehicle systems and wireless communications.
Vehicle software technology continues to evolve over time
and FCA US LLC, working with its suppliers, evaluates
and takes appropriate steps as needed. Similar to a com-
puter or other devices, your vehicle may require software
updates to improve the usability and performance of your
systems or to reduce the potential risk of unauthorized and
unlawful access to your vehicle systems.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 271

The risk of unauthorized and unlawful access to your
vehicle systems may still exist, even if the most recent
version of vehicle software (such as Uconnect software) is
installed.
WARNING!
•It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle systems,
including safety related systems, could be impaired
or a loss of vehicle control could occur that may
result in an accident involving serious injury or
death.
• ONLY insert media (e.g., USB, SD card, or CD) into
your vehicle if it came from a trusted source. Media
of unknown origin could possibly contain malicious
software, and if installed in your vehicle, it may
increase the possibility for vehicle systems to be
breached.
• As always, if you experience unusual vehicle behav-
ior, take your vehicle to your nearest Authorized
Dealer immediately. NOTE:
•
FCA or your dealer may contact you directly regarding
software updates.
• To help further improve vehicle security and minimize
the potential risk of a security breach, vehicle owners
should:
• Routinely check www.driveuconnect.com/software-
update to learn about available Uconnect software
updates.
• Only connect and use trusted media devices (e.g.
personal mobile phones, USBs, CDs).
Privacy of any wireless and wired communications cannot
be assured. Third parties may unlawfully intercept infor-
mation and private communications without your consent.
For further information, refer to “Privacy Practices – If
Equipped with Uconnect 8.4 radio” in “All About
Uconnect Access” in your Uconnect Owner ’s Manual
Supplement and “Onboard Diagnostic System (OBD II)
Cybersecurity”.
272 UNDERSTANDING YOUR INSTRUMENT PANEL