DODGE JOURNEY 2013 1.G Owners Manual

CavityCar-
tridge
FuseMini-
FuseDescription
F139 40 Amp
GreenClimate Control
System Blower
F140 30 Amp
PinkPower Locks
F141 40 Amp
GreenAnti-Lock Brake
System
F142 40 Amp
GreenGlow Plugs –
If Equipped
F143 40 Amp
GreenExterior Lights 1
F144 40 Amp
GreenExterior Lights 2
F145 30 Amp
PinkTo Body Computer –
LampCavityCar-
tridge
FuseMini-
FuseDescription
F146 30 Amp
PinkSpare
F147 30 Amp
PinkSpare
F148 40 Amp
GreenRadiator Fan Motor
F149 30 Amp
PinkStarter Solenoid
F150 25 Amp
NaturalPowertrain Control
Modules
F151 30 Amp
PinkHeadlamp Washer
Motor – If Equipped
F152 25 Amp
NaturalDiesel Fuel Heater –
If Equipped
7
MAINTAINING YOUR VEHICLE 569

CavityCar-
tridge
FuseMini-
FuseDescription
F153 20 Amp
YellowFuel Pump
F156 10 Amp
RedBrake/Electronic Sta-
bility Control Module
F157 10 Amp
RedTransfer Case Module
– If Equipped
F158 10 Amp
RedActive Hood Module
– If Equipped
F159 10 Amp
RedSpare
F160 20 Amp
YellowInterior Lights
F161 20 Amp
YellowHornCavityCar-
tridge
FuseMini-
FuseDescription
F162 50 Amp
RedCabin Heater #1/
Vacuum Pump –
If Equipped
F163 50 Amp
RedCabin Heater #2 –
If Equipped
F164 25 Amp
NaturalPowertrain Auto
Shutdown
F165 20 Amp
YellowPowertrain Shutdown
F166 20 Amp
YellowSpare
F167 30 Amp
GreenPowertrain Shutdown
570 MAINTAINING YOUR VEHICLE

CavityCar-
tridge
FuseMini-
FuseDescription
F168 10 Amp
RedAir Conditioner
Clutch
F169 40 Amp
GreenEmissions – Partial
Zero Emissions
Vehicle Motor
F170 15 Amp
BlueEmissions – Partial
Zero Emissions
Vehicle Actuators
F172 20 Amp
YellowSpare
F173 25 Amp
NaturalAnti Lock Brake
Valves
F174 20 Amp
YellowSiren – If EquippedCavityCar-
tridge
FuseMini-
FuseDescription
F175 30 Amp
GreenSpare
F176 10 Amp
RedPowertrain Control
Modules
F177 20 Amp
YellowAll Wheel Drive
Module – If Equipped
F178 25 Amp
NaturalSunroof – If Equipped
F179 10 Amp
RedBattery Sensor
F181 100
Amp
BlueElectrohydraulic
Steering (EHPS) –
If Equipped
7
MAINTAINING YOUR VEHICLE 571

CavityCar-
tridge
FuseMini-
FuseDescription
F182 50 Amp
RedCabin Heater #3 –
If Equipped
F184 30 Amp
PinkFront Wiper Motor
REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
Interior Bulbs
Bulb Number
Courtesy/Reading
Lamps (Incandescent)578
Courtesy/Reading
Lamps (Optional LED)LED (Serviced at
Authorized Dealer)
Glove Box Lamp 194
Cargo Lamp 579
Optional Door Map
Pocket/CupholderLED (Serviced at
Authorized Dealer)
For lighted switches, see your authorized dealer for
replacement instructions.
572 MAINTAINING YOUR VEHICLE

Exterior Bulbs
Bulb Number
Low Beam Headlamp 9006
High Beam Headlamp 9005
Front Park/Turn Signal 3757AK
Side Marker Lamp 168
Front Fog Lamp PSX24W
Center High Mounted
Stop Lamp (CHMSL)LED (Serviced at
Authorized Dealer)
License Lamp 168
Exterior Bulbs – Rear (LED Version)
Bulb Number
Rear Tail/Stop Lamp LED (Serviced at
Authorized Dealer)
Rear Tail (Liftgate) Lamp LED (Serviced at
Authorized Dealer)
Rear Turn Signal Lamp WY21W
Backup Lamp W21W
Exterior Bulbs – Rear (Bulb Version)
Bulb Number
Rear Tail/Stop Lamp P27/7W
Rear Tail (Liftgate) Lamp P27/7W
Rear Turn Signal Lamp PY27/7W
Backup Lamp P27/7W
7
MAINTAINING YOUR VEHICLE 573

BULB REPLACEMENT
Front Low/High Beam Headlamp, Turn
Signal/Park Lamp, And Side Marker Lamp
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the Totally Integrated Power
Module (TIPM) aside to replace certain lamps in the left
headlamp housing.
2. Rotate the applicable bulb and connector assembly ¼
turn counterclockwise and remove the assembly from
the headlamp housing.
3. Disconnect the bulb from the harness connector and
then connect the replacement bulb.
1 — Front Turn Signal/Park Lamp Bulb
2 — Side Marker Lamp Bulb
3 — Low Beam Headlamp Bulb
4 — High Beam Headlamp Bulb 574 MAINTAINING YOUR VEHICLE

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
4. Install the bulb and connector assembly into the
headlamp housing and rotate it ¼ turn clockwise to
lock it in place.
Front Fog Lamp
NOTE:Turn the steering wheel to the right if replacing
the left front fog lamp or to the left if replacing the right
front fog lamp to allow for easier access to the front of the
wheel well.
1. Remove the fasteners retaining the front lower wheel
well access panel and remove the access panel.2. Remove the electrical connector from the fog lamp
housing.
3. Squeeze the two tabs on the side of the bulb socket and
pull straight out from the fog lamp.
7
MAINTAINING YOUR VEHICLE 575

CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
4. Install the replacement bulb and connector assembly
straight into the fog lamp until it locks into place.
5. Reinstall the front lower wheel well access panel and
fasteners.
Rear Turn Signal And Backup Lamp
The taillamps are a two-piece design. The tail/stop/rear
turn signal lamps are located in the rear corner body
panels. The tail and backup lamps are located in the
liftgate.
Changing The Rear Turn Signal Lamp
1. Open the liftgate.
2. Remove the two fasteners from the inboard side of the
taillamp housing.
576 MAINTAINING YOUR VEHICLE

3. Carefully insert a trim stick (plastic flat-blade tool)
between the body panel and the outboard side of the
taillamp housing with one hand and grasp the flange
on the inboard side of the taillamp housing with the
other hand. Use the trim stick and hand pressure
together to disengage the taillamp housing from the
vehicle.
4. Rotate the applicable bulb’s electrical connector ¼ turn
counterclockwise and remove it from the taillamp
housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
taillamp housing and rotate the connector ¼ turn
clockwise to lock it in place.
7. Reinstall the taillamp housing and fasteners.Changing The Backup Lamp
1. Open the liftgate.
2.
Remove the two fasteners retaining the taillamp hous-
ing to the liftgate from the inboard face of the liftgate.
7
MAINTAINING YOUR VEHICLE 577

3. Carefully insert a trim stick (plastic flat-blade tool)
between the taillamp housing and the liftgate. Use the
trim stick and hand pressure together to disengage the
taillamp housing from the liftgate.4. Rotate the applicable bulb’s electrical connector ¼ turn
counterclockwise and remove it from the housing.
5. Remove the bulb from the connector socket and install
the replacement bulb.
6. Install the bulb and connector assembly into the
housing and rotate the connector ¼ turn clockwise to
lock it in place.
7. Reinstall the taillamp housing and fasteners.
578 MAINTAINING YOUR VEHICLE