relay DODGE RAM 1999 Service Service Manual

5) If PCM has not been replaced, and TEST VER-2A is being
performed after an A/C relay control circuit DTC test, ensure A/C is
on and go to next step.
6) Road test vehicle for at least 5 minutes. Road test
vehicle at a speed of at least 40 MPH at some point during road test.
Stop vehicle. Turn engine off for at least 10 seconds. Start engine
and continue road test. Ensure transmission shifts through all gears.
After road test, turn engine off and go to next step.
7) Using scan tool, read DTCs. If any DTC returns, perform
appropriate test(s). If no DTCs return, test is complete. Go to next
step.
8) Turn ignition on, with engine off. Using scan tool, erase
DTCs. Turn ignition off. Disconnect scan tool. Test is complete.
TEST VER-2A (DIESEL)
NOTE: If Accelerator Pedal Position Sensor (APPS), battery, Engine
Control Module (ECM) or Powertrain Control Module (PCM) has\
been disconnected or replaced, APPS must be reprogrammed and
correct vehicle mileage and Vehicle Identification Number
(VIN) must be programmed into PCM to prevent Diagnostic
Trouble Codes (DTCs) from being set in Anti-Lock Brake System\
(ABS) module and Supplemental Restraint System (SRS) module\
.
To program PCM and clear DTCs from ABS and SRS modules,
proceed to appropriate procedure listed below. On models
equipped with a Smart Key Immobilizer Module (SKIM), if
replacing Powertrain Control Module (PCM), secret key data
must also be updated to enable engine starting. To update
secret key data, proceed to appropriate procedure listed
below.
CAUTION: DO NOT attempt to adjust screws or disassemble APPS. Settings
are preset at factory and are not intended to by changed.
Procedure For Programming APPS
Reassemble all components. Turn ignition switch to ON or RUN
position without starting engine. Slowly press accelerator pedal to
floor once and slowly release. This procedure programs APPS
calibration in ECM. Go to step 1)).
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) If PCM has not been replaced, and TEST VER-2A (DIESEL) is\
being performed after a No Trouble Code (NTC) test, inspect vehicle to\
ensure all engine components are connected. Reassemble and reconnect
components as necessary. Check if initial symptom still exists. If
initial symptom exists, check for Technical Service Bulletins (TSBs)
that apply to vehicle and see TEST NTC-1A: NO TROUBLE CODE TEST MENU
in ENGINE PERFORMANCE, or appropriate TROUBLE SHOOTING - NO CODES

article in ENGINE PERFORMANCE for diagnosis by symptom. If initial
symptom no longer exists, test is complete. Go to step 6).
2) If PCM has not been replaced, and TEST VER-2A (DIESEL) is\
being performed after a DTC test, inspect vehicle to ensure all engine
components are connected. Reassemble and reconnect components as
necessary. Using scan tool, erase DTCs, reset all memory values and go
to step 4).
3) If PCM has not been replaced, and TEST VER-2A (DIESEL) is\
being performed after an A/C relay control circuit DTC test, ensure
A/C is on and go to next step.
4) Road test vehicle for at least 5 minutes. Road test
vehicle at a speed of at least 40 MPH at some point during road test.
Stop vehicle. Turn engine off for at least 10 seconds. Start engine
and continue road test. Ensure transmission shifts through all gears.
After road test, turn engine off and go to next step.
5) Using scan tool, read DTCs. If any DTC returns, perform
appropriate test(s). If no DTCs return, test is complete. Go to next
step.
6) Turn ignition on, with engine off. Using scan tool, erase
DTCs. Turn ignition off. Disconnect scan tool. Test is complete.
TEST VER-5A (EXCEPT DIESEL)
NOTE: If Powertrain Control Module (PCM) is replaced, correct
vehicle mileage and Vehicle Identification Number (VIN) must
be programmed into PCM to prevent Diagnostic Trouble Codes
(DTCs) from being set in Anti-Lock Brake System (ABS) modul\
e
and Supplemental Restraint System (SRS) module. To program
PCM and clear DTCs from ABS and SRS modules, proceed to
appropriate procedure listed below. On models equipped with a
Smart Key Immobilizer Module (SKIM), if replacing Powertrain
Control Module (PCM), secret key data must also be updated to\
enable engine starting. To update secret key data, proceed to
appropriate procedure listed below.
Procedure For Programming PCM & Clearing DTCs From ABS & SRS
Modules
Connect scan tool to Data Link Connector (DLC). Using scan
tool, enter correct VIN and mileage into PCM. Using scan tool
manufacturer's instructions, clear DTCs from ABS and SRS modules. Go
to step 1)).
Procedure For Updating Secret Key Data
Connect scan tool to Data Link Connector (DLC). Go to ENGINE
and then MISC menus on scan tool. Place SKIM in SECURED ACCESS MODE by
using appropriate Personal Identification Number (PIN) for this
vehicle. PIN may be obtained from owner, vehicle's invoice, or from
manufacturer. Select UPDATE THE SECRET KEY DATA. Data will be
transferred from Smart Key Immobilizer Module (SKIM) to PCM. Go to
step 1)).
1) Inspect vehicle to ensure all engine components are
connected. Reassemble and reconnect components as necessary. If any
DTCs have not been diagnosed, return to appropriate test(s). If all
DTCs have been diagnosed and repaired, go to next step.
2) Connect scan tool to Data Link Connector (DLC) if not
previously done. Ensure fuel tank is at least 1/4 full. Ensure A/C is
off. Go to next step.
3) Proper way to ensure DTC is repaired is to allow
Powertrain Control Module (PCM) to run monitor. Monitor operation may
be observed on scan tool. All specified enabling conditions for
specified DTC must be met before PCM will operate monitor. Go to next
step.

Fig. 3: Locating Intercooler & Components
Courtesy of Chrysler Corp.
8) Ensure connections on both batteries are tight and not
corroded. Ensure the three 32-pin connectors are fully engaged on
Powertrain Control Module (PCM). PCM is located on firewall at
passenger's side rear corner of engine compartment.
9) Check for loose, defective or corroded connections at
intake manifold air temperature sensor. See Fig. 4.
10) Ensure electrical connections on intake manifold air
heater relays and intake manifold air heater are tight and not
corroded. Intake manifold air heater relays are mounted on inner
wheelwell, below driver's side battery. See Fig. 5. Intake manifold
air heater is located between air inlet housing and intake manifold
cover. See Fig. 6.

Fig. 5: Locating Intake Manifold Air Heater Relays
Courtesy of Chrysler Corp.

13) On A/T models, ensure all electrical connectors are clean
and properly connected to electrical plugs on transmission case. On
all models, check for loose or defective electrical connections on
starter and starter solenoid.
MECHANICAL INSPECTION
Compression
Manufacturer does not provide information for checking
compression.
FUEL SYSTEM
AIR IN FUEL SYSTEM
NOTE: Air in the fuel system may cause hard starting, rough
running, excessive smoke, poor engine performance, engine
misfire, poor fuel economy and fuel knock. Air may enter fuel
system whenever fuel supply lines, fuel filter/water
separator, fuel injection pump, fuel injectors or high
-pressure fuel lines are removed or disconnected.
1) Inspect all low-pressure fuel lines from fuel tank to fuel
transfer pump, fuel heater and fuel filter/water separator for signs
of leakage. Inspect all high-pressure fuel lines for signs of leakage.
See FUEL INJECTOR & HIGH-PRESSURE FUEL LINES under FUEL SYSTEM.
2) After repairing fuel leak, bleed air from fuel system. See
FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article.
FUEL HEATER
1) Fuel heater is located in fuel filter/water separator. See
Fig. 1 . Fuel heater uses a fuel heater temperature sensor for
controlling operation of the fuel heater.
2) A defective fuel heater may cause excessive wax build-up
in the fuel filter/water separator during cold ambient temperatures.
Wax build-up may cause hard starting, prevent engine from
accelerating, low power, Blue smoke or White smoke. For testing of
fuel heater and fuel heater temperature sensor, see SYSTEM & COMPONENT
TESTING - TRUCKS - DIESEL article.
FUEL HEATER RELAY
Ensure fuel heater relay, located in power distribution
center is installed correctly and that terminals are not corroded. For
fuel heater relay testing, see SYSTEM & COMPONENT TESTING - TRUCKS -
DIESEL article.
FUEL FILTER/WATER SEPARATOR
NOTE: A blocked or restricted fuel filter/water separator may cause
starting problems, prevent engine from accelerating, low
power or White smoke. If an excessive amount of water
collects in filter/separator in a short period of time, it
may be necessary to drain and clean fuel tank.
1) When ignition switch is first turned to ON position,
WATER-IN-FUEL (WIF) warning light should come on for 2 seconds to
perform bulb and wiring circuit test and then go off. WATER-IN-FUEL
(WIF) warning light is located on instrument panel, just below the

tachometer.
2) If WATER-IN-FUEL (WIF) warning light stays on, water
should be drained from fuel filter/water separator. To drain water
from fuel filter/water separator, ensure engine is not running. Place
drain pan below drain tube at fuel filter/water separator. See Fig. 1.
3) Rotate handle on drain valve forward, toward front of
vehicle to OPEN position. Drain valve is located near top of fuel
filter/water separator. See Fig. 1.
4) Allow water to drain until clean flow of diesel fuel
exists. Rotate handle on drain valve back to CLOSE position.
FUEL TRANSFER PUMP
NOTE: A defective fuel transfer pump may cause low power, hard
starting and White smoke. Check fuel transfer pump output
pressure (cranking and starting), pressure drop and fuel
supply.
Fuel Transfer Pump Preliminary Inspection
1) Check for restricted or leaking fuel supply line to fuel
transfer pump or fuel return line located on driver's side of engine.
See Fig. 1 . Repair fuel supply line or fuel return line if restricted
or leaking.
2) Check for fuel leaking from fuel transfer pump. Replace
fuel transfer pump if fuel is leaking. Check fuel transfer pump output
pressure.
Fuel Transfer Pump Output Pressure
1) Clean area around filter fitting plugs, then remove plugs.
See Fig. 7 . Install Test Fittings (AVU1-2). Install Fuel Pressure Test
Gauge (6828) at inlet port. See Fig. 7. To prevent engine starting,
remove fuel injection pump relay, located in power distribution
center.
2) Turn ignition switch to START position. Inlet pressure
should be 5-7 psi. Install fuel injection pump relay. Start engine.
Inlet pressure should be 10 psi. Using a scan tool, clear FTC. FTC may
set when relay is removed. Check pressure drop.
Fig. 7: Checking Fuel Transfer Pump Output Pressure
Courtesy of Chrysler Corp.
Pressure Drop Test
Turn engine off. Move pressure gauge from inlet port to

NOTE: A leaking fuel injector or high-pressure fuel line may cause
a rough idle, Black smoke, poor engine performance, poor fuel
economy and fuel knock. Since a leaking high-pressure fuel
line may cause the same symptoms, check for leaking high
-pressure fuel line before checking fuel injector.
1) To determine which injector or line is malfuntioning,
start engine and check each cylinder output using scan tool. If scan
tool is not available, start engine and engine allow to idle. Loosen
high-pressure fuel line nut at each fuel injector in turn and listen
for a decrease in engine speed. Tighten high-pressure fuel line nut to
30 ft. lbs. (40 N.m). Go to next step.
2) To check for a leaking high-pressure fuel line, start
engine and allow engine to idle. Inspect high-pressure fuel lines and
connections for signs of fuel leakage by placing cardboard over high-
pressure fuel line and connection. Note if leak is being detected by
fuel being sprayed onto the cardboard. If leak exists, repair leak by
tightening high-pressure fuel line nut to 30 ft. lbs. (40 N.m) or
replacing high-pressure fuel line as necessary. If high-pressure fuel
line is replaced, bleed air from fuel system. See FUEL LINE BLEEDING
under FUEL SYSTEM in REMOVAL, OVERHAUL & INSTALLATION - TRUCKS -
DIESEL article. If no leaks are found, go to next step.
3) Remove suspect injector. See FUEL INJECTOR under FUEL
SYSTEM in REMOVAL, OVERHAUL & INSTALLATION - TRUCKS - DIESEL article.
Test injector with a diesel fuel injector tester. Follow tester
instructions. Replace fuel injector if fuel injector opening (pop)
pressure is not 4250-4750 psi (299-334 kg/cm
). Replace injector if
any leaks are noted at 291 psi (20 kg/cm) less than opening (pop)
pressure. Inspect injector for burrs, cracks, wear and plugging. Check
spray pattern. If any problems are noted, replace injector.
FUEL INJECTION PUMP TIMING
Improper fuel injection pump timing may result in low power,
excessive smoke and poor fuel economy. To check fuel injection pump
timing, see FUEL INJECTION PUMP TIMING in ADJUSTMENTS - TRUCKS -
DIESEL article.
INTAKE MANIFOLD AIR HEATER
NOTE: Intake manifold air heater is used to heat incoming air
before entering each cylinder. Warming of incoming air aids
in engine starting and improved driveability during cold
ambient temperatures. Engine Control Module (ECM) uses input
signals from various sensors for controlling intake manifold
air heater relays.
SUMMARY
If no faults were found while performing basic diagnostic
procedures, proceed to SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article. If no diagnostic trouble codes are found in self-diagnostics,
proceed to TROUBLE SHOOTING - NO CODES - DIESEL article for diagnosis
by symptom (i.e., ROUGH IDLE, NO START, etc.) or intermittent
diagnostic procedures.

Minimum Compression Pressure
Dakota
2.5L ........................................................ (1)
3.9L, 5.2L & 5.9L ............................. 100 psi (690 kPa)\
Durango ........................................ 100 psi (690 kPa)\
Ram Pickup ..................................... 100 psi (690 kPa)\
Ram Van Ram Wagon .............................. 100 psi (690 kPa)\
Maximum Variation Between Cylinders ............................ ( 1)
( 1) - Information is not available from manufacturer.









\









\









\









\









\









\









\







FUEL SYSTEM
FUEL PRESSURE RELEASE
WARNING: Fuel system is under high pressure. ALWAYS release fuel
pressure before attempting to open system for testing or
component replacement. DO NOT allow fuel to flow onto engine
or electrical parts while testing fuel system components.
Vehicles With Fuel Rail Test Port
1) Loosen fuel tank filler cap. Ensure ignition is off.
Remove protective cap from fuel rail test port.
2) Place one end of Fuel Pressure Release Hose (C-4799-1)
into an approved fuel container. Attach remaining end of hose to fuel
rail test port. Use care, as fuel system may be under pressure. Fuel
pressure will be released from fuel system. Remove hose, reinstall
protective cap, and fuel tank filler cap.
3) Wait 5 seconds. Use care when disconnecting fuel lines, as
some fuel pressure may still exist in fuel lines.
NOTE: One or more DTCs may set when fuel pump relay is removed.
Clear DTCs from PCM after fuel pressure release procedure. To
clear DTCs from PCM, see CLEARING DTCS under SELF-DIAGNOSTIC
SYSTEM in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article.
Vehicles Without Fuel Rail Test Port
1) Remove gas cap. Using a non-metallic tool, open flapper
valve in filler neck to relieve pressure. Remove fuel pump relay from
Power Distribution Center (PDC). Relays are identified on label under
PDC cover. Start and run engine until it stalls. Attempt to start
engine. Continue restarting engine until it will no longer run. Turn
ignition off.
CAUTION: DO NOT supply power to fuel injector for more than 4 seconds,
or fuel injector may be damaged.
2) Disconnect any fuel injector connector. Connect a jumper
wire between either fuel injector terminal and positive battery
terminal. Connect another jumper wire to other fuel injector terminal.
Momentarily touch other end of jumper wire to negative battery
terminal.
3) Place a shop towel under fuel line quick-connector at fuel
rail. Use care when disconnecting fuel lines, as some fuel pressure
may still exist in fuel lines. Disconnect fuel line quick-connector.
Reinstall fuel pump relay in PDC. Clear DTCs from PCM. To clear DTCs
from PCM, see CLEARING DTCS under SELF-DIAGNOSTIC SYSTEM in SELF-
DIAGNOSTICS - JEEP, TRUCKS & RWD VANS article.
FUEL PRESSURE TEST

NOTE: For additional information on fuel pressure and fuel pump
testing procedures, see appropriate NO TROUBLE CODE (NTC)
TEST and NO START (NS) TEST in SELF-DIAGNOSTICS - JEEP,
TRUCKS & RWD VANS article.
Vehicles With Fuel Rail Test Port
1) Disconnect negative battery cable. Release fuel pressure.
See FUEL PRESSURE RELEASE. Install fuel pressure gauge with hose on
fuel pressure test port.
2) Start engine and allow to idle. Fuel pressure should be
44-54 psi (3.1-3.8 kg/cm
). If no fuel pressure exists and engine will
not start, fuel pump relay and control circuit may be defective. See
FUEL PUMP RELAY.
3) If fuel pressure exceeds specification, fuel pump is okay,
but fuel pressure regulator is defective. Replace fuel pressure
regulator. Fuel pressure regulator is incorporated with the fuel
filter. Fuel filter/fuel pressure regulator is located on top of fuel
tank, in fuel pump module. See REMOVAL, OVERHAUL & INSTALLATION -
TRUCKS & RWD VANS - GASOLINE article.
Vehicles Without Fuel Rail Test Port
1) Disconnect negative battery cable. Release fuel pressure.
See FUEL PRESSURE RELEASE. Fuel pressure gauge is installed between
fuel supply line and fuel line fitting on fuel rail.
2) To disconnect fuel supply line from fuel rail, ensure area
around fuel supply line and fuel rail are clean. Note direction of
latch clip installation. Latch clip is located on top of fuel supply
line at fuel rail. See Fig. 1. Using 2 screwdrivers, pry latch clip
upward, and remove from fuel rail.
3) Pull fuel supply line from fuel rail. Install Adapter
(6923) into fuel rail. Ensure adapter is fully seated in fuel rail.
Install latch clip into fuel rail, with latch clip fingers pointing
downward. If latch clip will not fully seat so latch clip fingers
extend downward below fitting on fuel rail, adapter may not be fully
seated in fuel rail.
4) Connect fuel supply line to adapter. Ensure fuel supply
line fully seats in adapter. Remove protective cap from test port, and
install Fuel Pressure Gauge/Hose (5069) at test port.
5) Start engine and allow to idle. Fuel pressure should be
44-54 psi (3.1-3.8 kg/cm
). If no fuel pressure exists and engine will
not start, fuel pump relay and control circuit may be defective. See
FUEL PUMP RELAY.
6) If fuel pressure exceeds specification, fuel pump is okay,
but fuel pressure regulator is defective. Replace fuel pressure
regulator. Fuel pressure regulator is incorporated with the fuel
filter. Fuel filter/fuel pressure regulator is located on top of fuel
tank, in fuel pump module. See REMOVAL, OVERHAUL & INSTALLATION -
TRUCKS & RWD VANS - GASOLINE article.
7) On all models, release fuel pressure. See FUEL PRESSURE
RELEASE. Remove latch clip. Remove test equipment. Before reinstalling
fuel supply line, ensure fuel supply line fitting and fitting on fuel
rail are clean.
8) Lubricate fuel supply line fitting and fitting on fuel
rail with engine oil. Install fuel supply line on fuel rail.
9) Install latch clip into fuel rail, with latch clip fingers
pointing downward. Ensure latch clip is fully seated. Latch clip
fingers should extend downward below fitting on fuel rail when fully
seated.
10) Pull on fuel supply line to ensure fuel supply line is
fully locked on fuel rail. Reinstall negative battery cable. Start
engine and check for fuel leaks.

Fig. 1: Identifying Latch Clip & Installing Fuel Pressure Gauge
Courtesy of Chrysler Corp.
FUEL PUMP RELAY
On all models, if fuel pump relay or control circuit becomes
defective, a Diagnostic Trouble Code (FTC) may be stored in the PCM.
For additional information on diagnosis for fuel pump relay and
control circuit, see TEST TC-101A in SELF-DIAGNOSTICS - JEEP, TRUCKS &
RWD VANS article.
IGNITION CHECKS
NOTE: For ignition system spark testing and component testing, see
TEST NTC-2A in SELF-DIAGNOSTICS - JEEP, TRUCKS & RWD VANS
article.